UnintentionalChaos
International Hazard
Posts: 1454
Registered: 9-12-2006
Location: Mars
Member Is Offline
Mood: Nucleophilic
|
|
Sulfur
Any brillant suggestions for purifying some elemental sulfur? Someone mentioned hot toluene a while back, but I don't have any toluene lying around.
Thanks. I've seen 2H2S + SO2 done, but I'd really rather not mess with the lethal gas and a cloud of rotten-egg stink.
Department of Redundancy Department - Now with paperwork!
'In organic synthesis, we call decomposition products "crap", however this is not a IUPAC approved nomenclature.' -Nicodem
|
|
|
Elawr
Hazard to Others
Posts: 174
Registered: 4-6-2006
Location: Alabama
Member Is Offline
Mood: vitriolic
|
|
you could purify it by sublimation. I think that is how the medicinal product "flowers of sulfur" is manufactured from impure native sulfur.
1
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
Or by distillation in a current of CO2.
You should know what the likely impurities are. Some garden sulfur - marked 'wettable' - has a fair amount of organics - surface agents - and will
generate a lot of H2S when heated.
It doesn't hurt to stir the sulfur with cold water for awhile, decant or filter and repeat. This removes the surface active stuff as well as some of
the CaSO4 that's in some ag grade sulfur.
|
|
|
Sauron
International Hazard
Posts: 5351
Registered: 22-12-2006
Location: Barad-Dur, Mordor
Member Is Offline
Mood: metastable
|
|
Brauer's book probably has details on preparing ultrapure sulfur
But first of all, how pure do you need it?
Why not buy the grade you need and skip all the grunt work?
Alfa has grades purer than AR and pharm.
Some of Brauer's referenced procedures are laborious and others not so. I included the material on plastic sulfur and colloidal suflur. See attachment
below (341-343.pdf)
[Edited on 16-3-2007 by Sauron]
Attachment: 341-343.pdf (89kB)
This file has been downloaded 1456 times
|
|
|
Per
Hazard to Others
Posts: 134
Registered: 26-1-2007
Location: Europe
Member Is Offline
Mood: No Mood
|
|
Pure sulfur, hmm, I´ve here some kg with a purification of min. 99,9%, you could have a kg for only 7€, to bad that you live in the USA and I in
Germany.
|
|
|
Nicodem
Super Moderator
Posts: 4230
Registered: 28-12-2004
Member Is Offline
Mood: No Mood
|
|
| Quote: | Originally posted by UnintentionalChaos
Any brillant suggestions for purifying some elemental sulfur? Someone mentioned hot toluene a while back, but I don't have any toluene lying around.
|
I don't understand why you can not get toluene, but you could at least try with xylene. It should work even better as it has a higher boiling point
while the solubility of sulphur at the same temperature is probably quite similar.
…there is a human touch of the cultist “believer” in every theorist that he must struggle against as being
unworthy of the scientist. Some of the greatest men of science have publicly repudiated a theory which earlier they hotly defended. In this lies their
scientific temper, not in the scientific defense of the theory. - Weston La Barre (Ghost Dance, 1972)
Read the The ScienceMadness Guidelines!
|
|
|
Sauron
International Hazard
Posts: 5351
Registered: 22-12-2006
Location: Barad-Dur, Mordor
Member Is Offline
Mood: metastable
|
|
I suppose we would all be less confused if you would define for us:
1. What level of purity you require (and maybe why)
2. How much S you need to purify
3. Why you just don't buy pure S of required grade as it is cheap.
USP sulfur is not pure enough?
Brauer's procedures that I posted detail how to rigorously purify sulfure a Kg at a time to a very high purity.
So pls define your requirements and we can be more helpful perhaps.
|
|
|
BeanyBoy
Harmless
Posts: 47
Registered: 23-2-2007
Member Is Offline
Mood: No Mood
|
|
More Methods
I have a copy of Perrin, Armarego, & Perrin's "Purification of Laboratory Chemicals". It describes one very long procedure by Murphy, Clabaugh,
& Gilchrist, which appears to be meant to take fairly pure sulfur to "99.9999 moles per cent purity", but it is *way* long. Only by request.
Also mentioned: "crystallization from CS2, benzene, or bezene-acetone, followed by melting and degassing."
And: "Has also been boiled with 1% MgO, then decanted, and dried under vacuum at 40deg for 2 days over P2O5".
Mention is also made of an ACS monograph by Bartlett, Cox, & Davis, for purification of S6, recrystallization of S8, and "Bacon-Fanelli sulphur",
JACS, v83, p103-109.
I have page one of the monograph...
hth,
-the beantificator
|
|
|
UnintentionalChaos
International Hazard
Posts: 1454
Registered: 9-12-2006
Location: Mars
Member Is Offline
Mood: Nucleophilic
|
|
I didn't even realize this thread had been going anywhere, but thanks for looking into it. I'm as much into prepping my own chems from OTC sources as
I am about anything else and the only sulfur I can find is the 90% garden sulfur garbage (though a wash in water probably brought it up several
percent) Right now, I don't have a particular use in mind, but would like to have some should the need arise, so the cleaner the better. I can get
xylene, but I'm at college right now and everything is on hold for another two months anyway. 
Department of Redundancy Department - Now with paperwork!
'In organic synthesis, we call decomposition products "crap", however this is not a IUPAC approved nomenclature.' -Nicodem
|
|
|
Sauron
International Hazard
Posts: 5351
Registered: 22-12-2006
Location: Barad-Dur, Mordor
Member Is Offline
Mood: metastable
|
|
Ah. So this is a wild goose chase. You aren't interested in ultrapure sulfur but in getting the crap out of garden grade sulfur.
Sorry, decrapping inappropriate materials isn't really indexed in the lit. too often.
Really, you ought to just buy some "real" sulfur when you find a need for it. Most large pharmacies still sell USP grade flowers of sulfur which is as
OTC as you get and quite pure.
|
|
|
UnintentionalChaos
International Hazard
Posts: 1454
Registered: 9-12-2006
Location: Mars
Member Is Offline
Mood: Nucleophilic
|
|
I have been in more pharmacies than you can shake a stick at and no sulfur. I found USP KNO3 once, but that was an odd stroke of luck. Sauron, you
need to calm down. I'm sorry I didn't check the thread for a few days to clear up what was being asked. If I had enough equipment to pursue ultrapure
sulfur or to just sublime the crap, I wouldn't have asked. I was looking for an alternate to lots of hydrocarbons for my case, but I guess there isn't
a practical one. Please note that this is in beginnings for a reason. 
Department of Redundancy Department - Now with paperwork!
'In organic synthesis, we call decomposition products "crap", however this is not a IUPAC approved nomenclature.' -Nicodem
|
|
|
Sauron
International Hazard
Posts: 5351
Registered: 22-12-2006
Location: Barad-Dur, Mordor
Member Is Offline
Mood: metastable
|
|
I am perfectly calm. Perhaps you are too touchy.
|
|
|
Pyridinium
Hazard to Others
Posts: 258
Registered: 18-5-2005
Location: USA
Member Is Offline
Mood: cupric
|
|
| Quote: | Originally posted by Sauron
Ah. So this is a wild goose chase. You aren't interested in ultrapure sulfur but in getting the crap out of garden grade sulfur.
|
Bah. This board is full of tortuous routes for purifying things that could just be bought.
IIRC, Chaos, the solubility of sulfur in xylene is quite a bit lower than it is in toluene.
|
|
|
Eclectic
National Hazard
Posts: 899
Registered: 14-11-2004
Member Is Offline
Mood: Obsessive
|
|
To purify agricultural sulfur, why not try an agriculture related method. Make lime/sulfur solution by dissolving as much sulfur as possible in
boiling hydrated lime and water (calcium polysulfide solution). Decant and filter liquid after cooling, then precipitate sulfur with muriatic acid
(brick cleaner, HCl solution).
Probably a nasty, stinky process that really should be done in a barnyard, but better than poisoning yourself with aromatic solvents. Watch out for
H2S.
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
It is not so common for pharmacies in much of the US to carry sulfur, the old home remedy uses have faded and shelf space is too valuable to take up
with a very slow moving item.
Cleaning ag grade sulfur up usually means several good washes, perhaps extractions would be a better term. with water to remove the wetting agents.
Don't let the sulfur dry out between washes, once the wetting agent is gone it's tough to wet the sulfur. One or two washes with wet alcohol, the 70%
rubbing grade for example, might be a good finish. After that melting the sulfur and filtering it is perhaps the simplest cleanup that doesn't take
too much equipment.
Pyridinium - there are parts of the world, including sections of the USA, where it is difficult to by one chemical or another, even everyday ones.
Business licenses may be required, in the more urban areas it is not uncommon to find only various proprietary mixtures available to the public
instead of pure solvents and chemicals.
|
|
|
Pyridinium
Hazard to Others
Posts: 258
Registered: 18-5-2005
Location: USA
Member Is Offline
Mood: cupric
|
|
| Quote: | Originally posted by not_important
Pyridinium - there are parts of the world, including sections of the USA, where it is difficult to by one chemical or another, even everyday ones.
|
I know, I was just being facetious. I'm fascinated with primitive methods for chemistry, partly because that's how it was done for centuries.
Hence, I'm rather glad to see tortuous routes for making common things, or any routes for that matter. Today's common reagent is tomorrow's
hyper-regulated no-no, thanks to encroaching chemophobia and other reasons.
|
|
|
Aqua_Fortis_100%
Hazard to Others
Posts: 302
Registered: 24-12-2006
Location: Brazil
Member Is Offline
Mood: †
|
|
I have now some sulfur here.. 200g as "100% pure sulfur" from pharmacy and another amount of 700g of farm grade.
Is strange for me how in US the sellers can sell many "pure" solvents as toluene, xylene, acetone, MEK, etc and the simple elemental pure sulfur is a
bit more hard to find...
if one day i find here a OTC place which can sell me these solvents without suspicion, i will be very happy :-)
(here these substances are normally out of commerce because of use in drugs world)
Eclectic method for refining farm grade sulfur seems very OTC , cheap and easy to reproduce in backyard instead buy aromatic solvents, etc ..
although i think which the product isn't pure as the product from recrystalization method, and also the procedure should release poisonous H2S as
Eclectic says.
[Editado em 23-3-2007 por Aqua_Fortis_100%]
"The secret of freedom lies in educating people, whereas the secret of tyranny is in keeping them ignorant."
|
|
|
16MillionEyes
Hazard to Others
Posts: 153
Registered: 11-3-2007
Location: 16 Million Eyes, US
Member Is Offline
Mood: No Mood
|
|
Funny thing you ask for elemental sulfur and I have some myself but I don't know what to do with it. I haven't really thought of an interesting
reaction with sulfur.
|
|
|
indigofuzzy
Hazard to Others
Posts: 145
Registered: 1-10-2006
Location: DarkCity, Bay of Rainbows, Moon
Member Is Offline
Mood: Distilled
|
|
How would buying native sulfur from a mineral store work out, as far as being able to purify it?
Just as an example, one has native sulfur of unknown purity, and wants 90%+ purity. Or what if one wants 99.9%? How would one get there?
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
| Quote: | Originally posted by indigofuzzy
How would buying native sulfur from a mineral store work out, as far as being able to purify it?
Just as an example, one has native sulfur of unknown purity, and wants 90%+ purity. Or what if one wants 99.9%? How would one get there?
|
Mineral samples tend to be an expensive way to get sulfur, the agricultural grade is likely to be much cheaper. Gardening supply shops often carry it
It all depends on the exact sample of native sulfur. In general you'll need to melt it away from the rock. Using agricultural/gardening grade
starts with a a good washing with water to remove the organic wetting agents, this may mean multiple washes.
After that melting the sulfur and filtering it while hot will get rid of bits of rock or limestone/gypsum that is sometimes in Frasch method sulfur.
Sulfur from the Frasch process or recovered from petroleum processing is otherwise reasonably pure, 99 percent or higher. Volcanic deposit sulfur, as
most proper native sulfur specimens are, requires distillation or solution-filtration-crystallisation - which often leaves solvent trapped in the
sulfur and so is followed by distillation.
Agricultural sulfur starts off as fairly pure sulfur, then has wetting agents and other stuff added. Once those are removed, which water washing and
melting + filtering seem to do a decent job of, the remaining sulfur is pretty clean.
Beyond that level of purity come the various methods already discussed - refluxing with MgO and filtration, embedding a quartz heater at 700 C in the
molten sulfur and leaving it for some days; those have to be done under a CO2 or N2 atmosphere. That's to reach greater than 99.5% purity.
|
|
|
Diablo735
Harmless
Posts: 10
Registered: 8-8-2006
Location: Canada
Member Is Offline
Mood: No Mood
|
|
What about sulfur that comes in those trains? I live near train tracks and there are small piles of everything all over the tracks. There are nice
piles of sulphur, its yellow and it smells like it.(Haven't done any experiments to confirm. But pretty sure it is sulphur) Would that be high purity?
And how do I know the purity, any tests?
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
Wiki sez that Alberta is doomed to ne covered with sulfur from hydrodesulfurization of petroleum and natural gas, converted to the elemental form by
the Claus process.
This is a pretty good grade of sulfur. It should be free of mineral impurities, dissolving some would so if there were any insoluble trash; as you're
collecting spillage it could pick up dirt. It likely contains trace amounts of organic carbon compounds and sulfur oxides or sulfuric acid, extraction
with water and testing the pH of the extract would tell you if there was much oxidised sulfur.
I'd guess that for most purposes it will be pure enough, I'd do an acid removal wash before using it in pyrotechnics or at least test it for acid
content.
So head out to the tracks with your shovel and pail, and start stockpiling this resource.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
