| Pages:
1
2 |
NedsHead
Hazard to Others
Posts: 409
Registered: 9-12-2014
Location: South Australia
Member Is Offline
Mood: No Mood
|
|
I once made that mistake to ave, towards the end of the distillation there would be long periods of calm in the boiling flask followed by an eruption
of boiling and bumping that would shake the table, lucky for me my wife broke her favourite porcelain dish and the porous pieces are perfect as
boiling chips
|
|
|
Refinery
Hazard to Others
Posts: 371
Registered: 17-2-2014
Member Is Offline
Mood: Still
|
|
Has anyone tested an ordinary bleeder tube with air pump to induce bubble stream into sulfuric acid?
|
|
|
Fyndium
International Hazard
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
FYI, I concentrated sulfuric acid today. I used a teaspoon of activated carbon granules as boiling stones and it worked flawlessly. I still need to
concentrate the rest of them, and I consider vacuum distilling the acid itself to obtain higher concentration and purity. It would need approximately
180C with my vacuum pump, and it should do with paraffin wax bath at 200C. When concentrating sulfuric acid, I use bare propane gas heater because no
reasonable heating bath is capable of providing enough heat and being inert for boiling sulfuric acid at the same time in case of cracking. Being not
flammable, it is an exception in this matter for me.
I've introduced activated carbon into all distillations recently. I got a shot of acetone and styrene oxide from boiling flask when it bumped
violently because apparently the reaction was too clean to introduce any nucleation. Bumping is not just absolutely detrimental to distillation, but
also very dangerous, since spilling anything flammable is a call for disaster and it saved me from not getting a fire in my lab due to moving into
using induction heater and calcium chloride baths and spillage of acetone was only a call for cleanup and ventilation until resume. After letting it
cool down a little and adding - VERY carefully - even a few granules of carbon(it causes extreme frothing and it will easily foam over even bottoms
from boiling flask even when introduced into a hot liquid, and into a boiling it will just cause it to basically blow up, so it must be done at room
temp prior to heating, and even still gradually), it boiled absolutely flawlessly. Quarter of a teaspoon is very enough for 1 liter of liquid, since
even few singular granules were capable of holding a smooth boil. Carbon has the benefit of being one of the most porous substance in existence, but
still heavy enough to submerge in most forms of liquids we face in the lab for distillation, and of course, being inert for most stuff, exceptions
being few. It may also has the very minor effect of absorbing coloured impurities in some instances, and if this effect is desirable, increasing the
amount of granules is easy.
Not sure how it works at vacuum, but gonna test it out because I need a method to vacuum distill air sensitive stuff without bleeder tube and I do not
have magstir that is sufficient at heating anything above micro scale. My bleeder was apparently blocked last time, but there was enough nucleation
impurities to warrant a smooth boil anyways, so I see there is a chance carbon will do the job as well. I believe bleeder tube would work well with
air pump at ntp as well in bump prevention.
[Edited on 30-8-2020 by Fyndium]
|
|
|
Sulaiman
International Hazard
Posts: 3724
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Quote: Originally posted by hissingnoise  | | I've ever only used pyrex jugs on a hotplate and have never seen acid being ejected - slight bumping, yes, but nothing to worry about.
|
I'm surprised that a Pyrex jug on a hotplate survived,
maybe the inside bottom is scratched a lot relative to a typical rbf, giving lots of nucleation points?
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
KarelV
Harmless
Posts: 1
Registered: 4-12-2017
Location: Česká republika
Member Is Offline
Mood: Individualní
|
|
Kyeliny sírové zkoncentrujeme destilací
až na 98,7%ní*) a pak ochladíme pod 0°. Co vypadne, jsou krystaly
H2S04, kdežto voda zbude v matečném podílu kapalném, jejž prostě
slijeme nebo odstranime v odstředivce.
Edit(woelen): Next time please in english instead of Czech.
Translation: Concentrate sulfuric acid up to 98.7% *) by distillation and then cooling down below 0 °. What falls out are crystals of H2SO4, while
the water remains in the mother liquor, which simply can be drained or removed in a centrifuge.
[Edited on 2-4-21 by woelen]
|
|
|
rockyit98
Hazard to Others
Posts: 283
Registered: 12-4-2019
Location: The Known Universe
Member Is Offline
Mood: no mood is a good mood
|
|
Concentrating H2SO4 without distillation (with flask ans some PTFE )
"A mind is a terrible thing to lose"-Meisner
|
|
|
Aloesci
Harmless
Posts: 28
Registered: 7-4-2018
Member Is Offline
Mood: No Mood
|
|
OP also mentioned the problem of the Sulfuric Acid / SO3? fumes which start to come off well before coming close to 98%. When I went for the simple
'Boil away the water' approach, I was attempting to doing it outside with a cheap hotplate and 500ml beaker (least expensive option in case something
went wrong).
I started with about 35% conc sulfuric and once the volume had reached just below half it's original, it started to fume slightly. I came back 5
minutes later (doorbell went or something) and the whole 5m radius surrounding the beaker was just a thick cloud of acid and death. I turned off the
heat and carefully put a plank of wood over the beaker to stop the fumes before retreating because i was worried the neighbors would notice (i had
full PPE). Afterwards the acid was still only about 87%.
Has anyone figured out a way to safely and easily scrub the vapors so the azeotrope can be reached without requiring a huge open space? Even if it
results in substantial losses of acid?
|
|
|
Fyndium
International Hazard
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
Use a still. It will condense all the liquid coming over, effectively turning SO3 into H2SO4 with water and the little sulfuric acid that comes over
with it. People have successfully done this. I still recommend the ebulliator with aquarium air pump to agitate the boiling liquid to prevent bumping.
Any fumes that come through receiver flask, can be led to water/base trap, for example simple inverted funnel to prevent suckback.
Chinese 1L flasks, erlenmeyers and others cost about 10$ apiece, so using those to boil it off risks only that amount of your capital. The stillhead
and other parts will remain intact in case of flask failure.
|
|
|
| Pages:
1
2 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
