Cou
National Hazard
Posts: 958
Registered: 16-5-2013
Member Is Offline
Mood: Mad Scientist
|
|
I think hexane can be used as a Dean-Stark solvent alternative to benzene
http://www.sciencemadness.org/talk/viewthread.php?tid=154944
https://cpb-us-e1.wpmucdn.com/blogs.uoregon.edu/dist/1/8309/...
2nd link says hexane and water form an azeotrope boiling at 61.6 C and the vapor is 22.1% water.
One drawback is that salicylic acid is not soluble in hexane. For reactions with salicylic acid, you need benzene or toluene as the solvent.
Right now I am attempting a Dean-Stark fischer esterification with nonanoic acid, 1-pentanol (1.5 mol equiv), and hexane. I will update on how it goes
EDIT: I am very happy to say that it's working fine. Hexane and water are quickly forming layers in the dean-stark trap. Hexane is low boiling so it
reduces the amount of reactant escaping the flask
[Edited on 10-2-2020 by Cou]
|
|
|
Boffis
International Hazard
Posts: 1879
Registered: 1-5-2011
Member Is Offline
Mood: No Mood
|
|
That's interesting, I have often wonder if hexane or cyclohexane could be used as a substitute for benzene in azeotropic esterifications. Good luck
Cou!
|
|
|
Cou
National Hazard
Posts: 958
Registered: 16-5-2013
Member Is Offline
Mood: Mad Scientist
|
|
I was surprised at how fast the reaction finished, even at the low boiling temperature of hexane. All water was finished separating by 30 minutes, but
fischer esterification usually takes several hours.
|
|
|
brubei
Hazard to Others
Posts: 188
Registered: 8-3-2015
Location: France
Member Is Offline
Mood: No Mood
|
|
hexane may lead to solubility issue but its low boiling point probably allow the use a second solvent with higher bp and polarity.
I'm French so excuse my language
|
|
|
macckone
Dispenser of practical lab wisdom
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
n-butanol can also be used. Again it depends on reactant solubility.
It has non-zero solubility in water but works well for removing water with a dean stark trap.
|
|
|
Boffis
International Hazard
Posts: 1879
Registered: 1-5-2011
Member Is Offline
Mood: No Mood
|
|
But won't the butanol also form an ester?
|
|
|
Fery
International Hazard
Posts: 1026
Registered: 27-8-2019
Location: Czechoslovakia
Member Is Offline
|
|
I used hexane succesfully when making esters (to remove water completely), there are some threads here in the forum. Also making anhydrous
allylalcohol from azeotrope (70%) worked well. Sometimes I used a fraction obtained by distilling medicinal petrolether, so no pure hexane but mixture
of isomers.
|
|
|
Cou
National Hazard
Posts: 958
Registered: 16-5-2013
Member Is Offline
Mood: Mad Scientist
|
|
The nice thing about low boiling point of hexane is that it prevents reagents from escaping into the dean-stark trap, which sometimes messes up
separation of water.
If that becomes an issue, you can use a 3 neck flask and periodically add the organic layer in the Dean-stark trap back into the flask
[Edited on 10-2-2020 by Cou]
|
|
|
Corrosive Joeseph
National Hazard
Posts: 915
Registered: 17-5-2015
Location: The Other Place
Member Is Offline
Mood: Cyclic
|
|
Toluene.....?
/CJ
Being well adjusted to a sick society is no measure of one's mental health
|
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
I recall using isooctane once when measuring the water content of some greasy stuff.
Worked very nicely.
|
|
|
Cou
National Hazard
Posts: 958
Registered: 16-5-2013
Member Is Offline
Mood: Mad Scientist
|
|
For some reactions, the boiling point of toluene is too high, which can cause reagents to boil over into the dean-stark trap and not be able to
return.
If both of your reagents are high boiling point, like salicylic acid and octyl alcohol, then yea toluene would be okay.
|
|
|
macckone
Dispenser of practical lab wisdom
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
Yes it can, good point since this was for a fischer esterification.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
