Pumukli
National Hazard
Posts: 708
Registered: 2-3-2014
Location: EU
Member Is Offline
Mood: No Mood
|
|
How to repair a thermocouple?
I have a thermocouple at the end of a meter long wire-pair, (thermometer sensor.) Unfortunately one of the wires broke at the small junction globule.
I'd like to repair it but don't know how to proceed.
I thought of discharging a bigger electrolytic capacitor into this junction and make it remelt again. (But how much joules?)
I know the couple is cheap (USD 1, including shipping and handling, maybe), but I don't want to bin it yet.
Had anyone repaird a thing like this?
|
|
|
Sigmatropic
Hazard to Others
Posts: 307
Registered: 29-1-2017
Member Is Offline
Mood: No Mood
|
|
Sand the wires and wrap 'm together. Worked fine in my case.
|
|
|
happyfooddance
National Hazard
Posts: 530
Registered: 9-11-2017
Location: Los Angeles, Ca.
Member Is Offline
Mood: No Mood
|
|
Yes, I did it similar to how you described, I welded it by discharging a capacitor from what I believe was a 12v power supply. I'm not sure the amount
of energy discharged, but I varied it (by using a resistor), and it took a few (maybe 2 or 3) tries before I got a clean weld. I cleaned the pieces
between tries and added a small amount of flux (probably a mix of dilute HCl, Zinc Chloride, and borax or tri-sodium phosphate).
There is a certain trick to getting the arc to form in the right spot, I'm not a welder or an expert, but for me the ends needed to be more parallel
and less tip-to-tip, if that makes sense.
|
|
|
Fulmen
International Hazard
Posts: 1725
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
If it's used for low temperature you can solder it.
We're not banging rocks together here. We know how to put a man back together.
|
|
|
morganbw
National Hazard
Posts: 561
Registered: 23-11-2014
Member Is Offline
Mood: No Mood
|
|
Not the correct way but just twisting the wires at the junction often work remarkably well.
Just saying.
[Edited on 1/6/2019 by morganbw]
|
|
|
Twospoons
International Hazard
Posts: 1326
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
I've used the arc from a neon sign transformer to make thermocouples. Melts a nice little ball on the end of the wire.
As has been said, soldering works too, though you need an aggressive flux such as ZnCl / HCl.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
|
Fulmen
International Hazard
Posts: 1725
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
In my experience twisting and soldering works fine without any special flux. At least for "single use" or non-critical applications. We routinely
measured heat production in curing concrete, the TC was twisted&soldered with regular 50/50 flux core and embedded un-shielded into the wet
concrete. This worked fine for at least a week.
We're not banging rocks together here. We know how to put a man back together.
|
|
|
Twospoons
International Hazard
Posts: 1326
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
Your 50/50 solder probably does have an aggressive flux, given the usual application for that alloy is soldering pipes etc. This is different to 63/37
Sn/Pb used in electronics, which usually has a much milder flux, and in my experience doesn't work as well with nickel alloys.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
|
Sulaiman
International Hazard
Posts: 3721
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
For temporary use twisting wires together works ok,
type J used in a lot of older equipment can be soldered,
I've never succesfully soldered type K
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
i don't think soldering would be a good idea, i mean a thermocouple works because when to different metals are in contact and are heated they generate
a small electric potential, if you solder them with a random filler metal, the propriety of the probe would change right?
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
Fulmen
International Hazard
Posts: 1725
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
My bad, I meant the standard fine electronics solder. I suspect it acted more like an adhesive, and that the electrical contact was formed by twisting
the pair. Either way it performed flawlessly, even when suspended in concrete.
As for the TC a solder joint shouldn't affect the performance. The chromel-solder / solder-alumel dual couple would produce the same voltage
difference as the standard chromel-alumel couple.
We're not banging rocks together here. We know how to put a man back together.
|
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Solder may work but it most certainly will change the temperature/voltage curve of the thermocouple. It may, however, still operate acceptably well,
but no guarantees.
|
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Ubya  | | i don't think soldering would be a good idea, i mean a thermocouple works because when to different metals are in contact and are heated they generate
a small electric potential, if you solder them with a random filler metal, the propriety of the probe would change right? |
Odd as it seems, as long as all the soldered bits are at the same temperature, the solder does not affect the output voltage.
So, chromel, solder, alumel gives the same voltage as chromel, alumel. (provided that the alumel solder and solder chromel junctions are at the same
temperature).
|
|
|
yobbo II
National Hazard
Posts: 764
Registered: 28-3-2016
Member Is Offline
Mood: No Mood
|
|
The soldering will work as long as you are measuring lowish temps. If you go near the melting temp. of the solder the junction will dissolve into the
solder and things will not work. Brazing will work so long as you do not go near the melting temp. of the braze. If you go near the ....... (as with
the solder above!)
Try to melt wires together. Not easy to do.
Yob
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
