CobaltChloride
Hazard to Others
Posts: 239
Registered: 3-3-2018
Location: Romania
Member Is Offline
|
|
What are the condensers that work for both reflux and distillation
Would a 300mm Dimroth condenser work equally well for both distillations (used in the same position as a Liebig condensers) and refluxes? Would the
fact that the heavy cooling water tube hangs from just two small points make it prone to breaking during use? If this condenser is not good, is there
any other condenser that is great for both refluxes and distillations?
|
|
|
NEMO-Chemistry
International Hazard
Posts: 1559
Registered: 29-5-2016
Location: UK
Member Is Offline
Mood: No Mood
|
|
Far as I know a Dimroth is made for reflux, that the point of them. As to other use I wouldnt know but would guess if you set a reasonable limit on
what your asking it to do, then it should be ok. I got all kinds of condenser but actually only really use a friedrick or Ahlin for most things, you
can see the vapor front.
Rule of thumb i use is if it dosnt get past 3-4 coils then its fine. The Ahlin or whatever its called, i use with stainless steel scrubber pads as a
kind of fractional condenser. I dont have the luck with Graham condensers they seem to flood and spit for me and i got a decent one.
I have a Liebig and have honestly never used it.
|
|
|
happyfooddance
National Hazard
Posts: 530
Registered: 9-11-2017
Location: Los Angeles, Ca.
Member Is Offline
Mood: No Mood
|
|
Leibig, West, cooled coil, dimroth, vigreux, just a plain tube with a fan blowing on it...
A dimroth won't break from thermal stress if it is built/annealed properly.
[Edited on 3-27-2018 by happyfooddance]
|
|
|
zed
International Hazard
Posts: 2284
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
I think of the Graham as a distillation condenser, or a scavenger reflux condenser. Something to place atop a less efficient condenser, to catch a
little escaping vapor, after the primary reflux condenser has done its job.
The Grahams I currently own, are the 200mm type. Very efficient. Very small diameter coil tubes inside. Easily plugged-up. If I tried to use them
as regular reflux condensers, a vigorous reflux, would rocket propel them through the ceiling.
There is no perfect condenser that works well for every application. Moreover, what we might call "better condensers" cost a bundle. They can
still break however.
The Liebig and the Alihin, are both pretty versatile, and reasonably priced.
At least, for many of us, they are reasonably priced. Being in the U.S., most of us can buy glassware dirt-cheap, postage free, from China.
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
You can use a Dimroth almost anywhere. They aren't quite as efficient as Graham condensers, but Dimroths are almost as efficient as Grahams, and
Dimroths are less susceptible to getting flooded by bumping. Usually, you can swap a Dimroth condenser in for a Liebig; I typically only avoid it when
I am worried about breaking it or think it might be hard to clean the condenser afterward. I don't even have a Graham condenser.
[Edited on 28-3-2018 by JJay]
|
|
|
Texium
Administrator
Posts: 4619
Registered: 11-1-2014
Location: Salt Lake City
Member Is Online
Mood: PhD candidate!
|
|
Our wiki has a nicely detailed page about different condenser styles: http://www.sciencemadness.org/smwiki/index.php/Condenser
|
|
|
CobaltChloride
Hazard to Others
Posts: 239
Registered: 3-3-2018
Location: Romania
Member Is Offline
|
|
Quote: Originally posted by happyfooddance  | Leibig, West, cooled coil, dimroth, vigreux, just a plain tube with a fan blowing on it...
A dimroth won't break from thermal stress if it is built/annealed properly.
[Edited on 3-27-2018 by happyfooddance] |
And do you think that one from deschem from ebay (https://www.ebay.com/itm/331106170297) would be annealed properly?
|
|
|
Radium212
Hazard to Self
Posts: 85
Registered: 26-6-2017
Member Is Offline
Mood: Pyrophoric.
|
|
My Graham tends to choke up and spit in distillations, but runs pretty well in refluxes.
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
Given I used the liebig to distill sulfuric acid and ethylene glycol and no issue what so ever I'd wager his manufacturer does a good job of it! I
order from them all most exclusively now as had very good dealings and they are good at comm's!
Interestingly I just ordered the 300mm version of that! Will be for my azide synth.
[Edited on 28-3-2018 by XeonTheMGPony]
|
|
|
zed
International Hazard
Posts: 2284
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Deschem is reputable. As a bonus, your shipment might appear after only a week or so.
It isn't a certainty, delivery times can vary, but on several occasions my orders have shown up in seven days or less.
In glassware, nothing is certain. Alas, glassware is all too mortal.
You pays yer nickel, and you takes yer chances.
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by zed | Deschem is reputable. As a bonus, your shipment might appear after only a week or so.
It isn't a certainty, delivery times can vary, but on several occasions my orders have shown up in seven days or less.
In glassware, nothing is certain. Alas, glassware is all too mortal.
You pays yer nickel, and you takes yer chances. |
Can't say it any better then that really, eventually I want two of every thing so when it does pop I have a spare on hand, but till I can start making
some money off of it can't do much (Mint oil and other extracts where I made my doll back in the lands of hills and trees!)
|
|
|
CobaltChloride
Hazard to Others
Posts: 239
Registered: 3-3-2018
Location: Romania
Member Is Offline
|
|
| Quote: Originally posted by zed | Deschem is reputable. As a bonus, your shipment might appear after only a week or so.
It isn't a certainty, delivery times can vary, but on several occasions my orders have shown up in seven days or less.
In glassware, nothing is certain. Alas, glassware is all too mortal.
You pays yer nickel, and you takes yer chances. |
I've ordered from them before and it took two and a half months to arrive, but this is most probably due to the lazy customs workers in my country
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
time of year playes a big role too, I suspect my orders will take ruffely a month given time of year and weather n such.
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
I have that exact Dimroth, and it works fine. The only criticism I have of it is that 3/8 vinyl tubing doesn't grip the hose barbs tightly, so I have
to use small latex spacers to prevent leaks, but that's typical.
|
|
|
zed
International Hazard
Posts: 2284
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Cobalt Chloride,
It would be nice if you could find inexpensive glassware closer to home. Glassblower?
Many of us seem to reside on the West Coast of the United States.
As such, we enjoy a special relationship with the Far East. China and Japan, are geographically quite close to us.
Thus, the Chinese, who covet American Dollars, can deliver us glassware cheaply and promptly.
Two and a half months, is a long, long wait. I would go crazy.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
