GoldAlchemist
Harmless
Posts: 5
Registered: 26-12-2014
Member Is Offline
Mood: No Mood
|
|
Liquid to solid Sodium Cyanide
I'm looking for some advice on dehydrating liquid Sodium Cyanide to a dry powder state.
I plan on distilling off the water from 50 liters of 30% liquid (commercial grade) NaCN. I plan on using a heating mantle with a 5 liter rbf set up
for distillation in order to remove H2O. This will take place in a fumehood with filtered fan extraction. I also have a proper rated respirator that
will be used.
I don't plan to distill that liquid to a completely dry state as I think I will do this in a vacuum desiccator.
I'm aware that NaCN has a very high boiling point and I'll not get anywhere near that and NaCN should be kept away from metals.
My only concern is that I might be missing something by conducting this experiment.
Any advice would be appreciated.
|
|
|
subsecret
Hazard to Others
Posts: 424
Registered: 8-6-2013
Location: NW SC, USA
Member Is Offline
Mood: Human Sadness - Julian Casablancas & the Voidz
|
|
You don't even need to distill the water, just boil it off. When most of the water is gone from the mixture, put it on a steam bath and heat for a few
hours. Actually, a shallow dish would be better, as it's very difficult to remove saltcakes from round-bottom flasks.
The only advantage of a distillation is that any mist from the boiling solution would be captured. This could be solved with a cotton or glass wool
plug in the mouth of the open flask, if you plan to use one. In theory, the fiber should not be saturated with water (liquid water, that is) when it's
temperature reaches that of the steam around it. But hopefully, you won't use a flask, so you don't have to deal with a saltcake INSIDE a tiny
opening.
What does the suction hole look like on the fume hood? Is it a single opening, or is it baffled? If it's single, it'll be easy to put a cheap rag over
it to catch any cyanide mists. Just dispose of it properly when you're done. If it's baffled, just use more cloth.
When heating, it's important not to heat the slurry too long, as this can cause it to spatter as it gets hot.
Judging by your username, and the fact that you have 50 L 30% NaCN, I'm certain that you'll handle your waste in the right way.
Fear is what you get when caution wasn't enough.
|
|
|
GoldAlchemist
Harmless
Posts: 5
Registered: 26-12-2014
Member Is Offline
Mood: No Mood
|
|
Thanks for the response. I had thought about boiling off by using a erlenmeyer but I figured more of a closed system would be extra safe for myself
and others.
The cheap rag sounds like a good idea as well as I have non baffled fume hood.
|
|
|
cyanureeves
National Hazard
Posts: 744
Registered: 29-8-2010
Location: Mars
Member Is Offline
Mood: No Mood
|
|
ive always wondered if any hydrogen cyanide would be release along with steam if an aqueous cyanide solution was boiled.doesnt cyanide only bond with
some metals though?so then cyanide acts like a salt in which it will not boil off after water is evaporated?i was scared to death when dealing with
steam and wore a gas mask even when electroplating.some plating solutions work great when warmed and though i sort of doubted the steam was dangerous
i began to wonder if cyanide could be released electrically with the anode.
|
|
|
subsecret
Hazard to Others
Posts: 424
Registered: 8-6-2013
Location: NW SC, USA
Member Is Offline
Mood: Human Sadness - Julian Casablancas & the Voidz
|
|
Thanks cyanureeves, I never considered that.
GoldAlchemist, if you're willing to sacrifice a little bit of purity, add a spatula-full of sodium hydroxide to the solution to be
doubly certain that the CN- can't hold onto a proton.
Fear is what you get when caution wasn't enough.
|
|
|
S.C. Wack
bibliomaster
Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline
Mood: Enhanced
|
|
If someone tried this on a large scale, they could die. Look up hydrolysis of cyanide. The addition of hydroxide is wise. If not added, it will be
made...NaCN + H2O -> HCN + NaOH..also the CO2 in air will not help...
|
|
|
dermolotov
Hazard to Others
Posts: 114
Registered: 13-12-2014
Location: Toronto, Canada
Member Is Offline
Mood: Free
|
|
Quote: Originally posted by S.C. Wack  |
If someone tried this on a large scale, they could die. Look up hydrolysis of cyanide. The addition of hydroxide is wise. If not added, it will be
made...NaCN + H2O -> HCN + NaOH..also the CO2 in air will not help... |
Yes. I would NOT work with cyanide AT ALL due to its "deadly houdini" magic tricks.
The best way to deal with any sort of cyanide heating is in an anhydrous atmosphere away from acids or bases. If using any of those with cyanides, I
would have a bubbler system leading into a beaker full of Sodium Hydroxide in case.
I believe that is what my companions in the inorganic community does when they work with hydrated cyanide ligands.
|
|
|
subsecret
Hazard to Others
Posts: 424
Registered: 8-6-2013
Location: NW SC, USA
Member Is Offline
Mood: Human Sadness - Julian Casablancas & the Voidz
|
|
Good point, SC.
Even with a distillation apparatus, the solubility of cyanide in water will limit how much can be trapped in the collection flask. A gas scrubber
loaded with sodium hydroxide would be a good way to clean the gas stream, just remember that there'll be cyanide in this when the process is finished.
Hydrolysis and off-gassing of HCN would result in the terrible consequence of a decreased yield. Oh, maybe a little bit of death.
Fear is what you get when caution wasn't enough.
|
|
|
dermolotov
Hazard to Others
Posts: 114
Registered: 13-12-2014
Location: Toronto, Canada
Member Is Offline
Mood: Free
|
|
| Quote: Originally posted by Awesomeness | | Even with a distillation apparatus, the solubility of cyanide in water will limit how much can be trapped in the collection flask. A gas scrubber
loaded with sodium hydroxide would be a good way to clean the gas stream, just remember that there'll be cyanide in this when the process is finished.
|
Add Hydrogen Peroxide to any and all glassware that has come in contact with cyanides. It oxidises it to cyanate that can actually be safely flushed
down the drain. Better to bring it to your local disposal site but I believe a mixture of peroxide, hydroxide, and small amounts of cyanate is
filtered out at the treatment plant.
Any leftover solution should be mixed with the peroxide as well.
|
|
|
GoldAlchemist
Harmless
Posts: 5
Registered: 26-12-2014
Member Is Offline
Mood: No Mood
|
|
Thanks for everyones feedback. I was concerned about Hydrolysis and probably should have considered CO2 in atmosphere as a potential hazard.
The sodium hydroxide collection flask is a good addition to the setup that I had not thought about either but it makes sense as monitoring ph is not
very feasible and is a good backstop.
|
|
|
subsecret
Hazard to Others
Posts: 424
Registered: 8-6-2013
Location: NW SC, USA
Member Is Offline
Mood: Human Sadness - Julian Casablancas & the Voidz
|
|
I expect that boiling that much solution down will require a long time. Be sure to use a flask that you aren't too attached to, as the NaOH, though
dilute, might have time to etch the glass. Definitely teflon tape/grease your joints.
Fear is what you get when caution wasn't enough.
|
|
|
forgottenpassword
Hazard to Others
Posts: 374
Registered: 12-12-2013
Member Is Offline
Mood: No Mood
|
|
Can't you just precipitate it with acetone, or something? With the amount of time and effort and money needed to distill 50 litres of water it may be
cheaper to just buy 200 litres of acetone and precipitate it out. If not acetone then something else: I haven't looked into it.
|
|
|
Fulmen
International Hazard
Posts: 1725
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
While lye can and will attack borosilicate glass it's not going to eat a hole in a beaker in a short time. I've boiled strong solutions of 75/25
NaOH/KNO3 (BP appr 140°C) many times, and while this proved too aggressive in the long term it took many hours of boiling and months of storage at
room temperature before it became a real safety issue. Not something you'd want to subject precious glass ware to but it's not going to eat a hole in
a couple of hours.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
