woelen
Super Administrator
Posts: 8027
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Unreactive properties of KClO4?
I have done quite a few experiments with Mg(ClO4)2, NaClO4 and also some with HClO4 and now I have quite some waste, containing perchlorate. I worked
up the waste with KCl and made KClO4 from it (which actually is surprisingly easy, it dissolves well in hot water, while being almost insoluble in
cold water) and recrystallized twice from distilled water. I now have some pure KClO4, a snow-white crystalline solid, which easily can be crunched
into a white powder.
I just wanted to make a pyrotechnic mix of this KClO4 with sulphur just for the fun of it (nice demo for kids), but to my surprise this mix cannot be
ignited  and the kids were very disappointed. I mixed 2 parts of KClO4 with 1
part of sulphur (appr. stoichiometric ratio for KClO4 + 2S --> KCl + 2SO2). But even when some of the mix is kept on a spatula inside the flame of
an alcohol burner, this mix does not ignite! The sulphur melts and fizzles somewhat and becomes dark yellow and that's all.
I am a noob in the field of pyrotechnics, but this is not what I expected. If I make a similar mix from KClO3 and S, then the mix very easily ignites
and the ratio is not critical at all.
When I add a little amount of red P (just 1% or so) to the mix of KClO4 and sulphur, then it can be ignited easily, but I do not like to use my red P
in pyro-mixes as red P is too valuable to be wasted for such things.
What are your experiences with KClO4? Do you also have difficulties igniting mixes with this chemical?
[Edited on 9-9-09 by woelen]
|
|
|
1281371269
Hazard to Others
Posts: 312
Registered: 15-5-2009
Member Is Offline
|
|
67% KClO4, 33% Al is supposed to be a good mix. Also KClO4 with sugar.
|
|
|
Jor
National Hazard
Posts: 950
Registered: 21-11-2007
Member Is Offline
Mood: No Mood
|
|
I have no experience with pyro, but I do remember that I once mixed a small amount of KClO4 with red P. It was no more than 100mg of mix. Even when a
few mg are ignited you get bright flashes. Really amazing. Really fun stuff I can recommend, although stay under 100mg, as the mix is really powerful.
That's the only thing I have done with KClO4. I find it a rather useless chemical, as I don't do pyro (like once a month with a 100mg amount, thats
all).
I wish I had NaClO4, wich is much more interesting.
[Edited on 13-9-2009 by Jor]
|
|
|
woelen
Super Administrator
Posts: 8027
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
I also tried the mix of Mossydie, but that also cannot easily be ignited. Even when kept in the flame of a propane torch, it does not ignite. After
that, I tried a somewhat modified mix, taking 130 mg of finely ground KClO4, 35 mg of 2000 mesh Al-powder (so-called German dark) and 10 mg of
sulphur. This mix still is hard to ignite, but when it goes, it goes BLITZ. I then prepared the same KClO4/Al/S mix, but now also added 2 mg of red P.
When this is done, it still is very powerful and flashing, but now ignition is very easy, just keep it near the flame of an alcohol burner, not even
need to keep it in the flame.
Based on this, I come to the conclusion that KClO4 is a powerful oxidizer, but you need quite some heat in order to ignite mixes with this, just like
with thermite reactions. When even a tiny amount of red P is added, then it can easily be ignited, probably even so easily that the mix becomes
dangerous to keep around.
|
|
|
densest
Hazard to Others
Posts: 359
Registered: 1-10-2005
Location: in the lehr
Member Is Offline
Mood: slowly warming to strain point
|
|
***DANGER**** KClO4 and P deflagrates/close to detonates on NO provocation. It is what pyrotechnics people call a "death
mix".
KClO4 and finely powdered Al (or Mg, or Zr) burns at a rate close to the DDT (deflagration/detonation transition). More than 50 mg in a container with
a fuse without a license in the US is a felony and actively pursued by the DHS, etc.
Adding S to KClO4/Al sensitizes it significantly.
Most of the "fireworks factory explosions" in the news over the last 10 years have involved large quantities of KClO4/Al mix (flash powder). It is
sensitive to friction, heat, spark, and chemical stimulus.
Mix up 10-20 mg of perchlorate/p and tap it with something metallic. It will go BANG.
Mixed with fuels like red gum it makes a very good pyrotechnic color base.
[Edited on 14-9-2009 by densest]
|
|
|
ketel-one
Hazard to Self
Posts: 55
Registered: 8-9-2009
Location: Pluto (planet?)
Member Is Offline
Mood: No Mood
|
|
Zinc seems nice because it's super obtainable. Just broke into couple alkaline batteries, trying to do this experiment: http://woelen.homescience.net/science/chem/exps/bleach/index.... If I can really obtain NaMnO4 from MnCl2 +NaOCl that would be something. Although
I guess it's a weaker oxidizer than KClO4 seeing as Mn is much easier put into that oxidation state than Cl.
EDIT(woelen): Changed link, so that it works again.
[Edited on 6-5-14 by woelen]
|
|
|
woelen
Super Administrator
Posts: 8027
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
@densest: Yes, I agree with your observations that KClO4/Al is a very powerful flash mix, but what I observe is that it is not easily ignited at all.
I tried the KClO4/P mix and it burns violently, but it does not set off when tapped. Maybe if hammered, but I did not try that,
I also tried KClO3/P and that is extremely sensitive. I have a demo on my website of the sensitivity of this mix, just tapping 10 mg or so with a
glass rod (not heavy banging, just tapping) leads to explosion.
http://woelen.homescience.net/science/chem/exps/raw_material...
Are you sure that in some cases you confuse the properties of KClO3 with those for KClO4? KClO4 does make powerful flash mixes, but my experience is
that mixes, based on KClO4 need quite some heat before they ignite, even when sulphur is present.
@ketel-one: That demo is nice for showing how bleach can oxidized manganese to oxidation state +7 but it is not useful for preparation of
permanganates. What you see in that experiment is a very very dilute solution of permanganate, even a 1% solution already is nearly black. Its color
is very intense. Besides that, isolating NaMnO4 from a solution is more or less impossible if so many other impurities are present. Lookup the thread
on making permanganates over here. Member "Der Alte" has done a lot of experiments in this area and what he has written on the subject is a good read.
|
|
|
JohnWW
International Hazard
Posts: 2849
Registered: 27-7-2004
Location: New Zealand
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by woelen  | (cut)
@ketel-one: That demo is nice for showing how bleach can oxidized manganese to oxidation state +7 but it is not useful for preparation of
permanganates. What you see in that experiment is a very very dilute solution of permanganate, even a 1% solution already is nearly black. Its color
is very intense. Besides that, isolating NaMnO4 from a solution is more or less impossible if so many other impurities are present. Lookup the thread
on making permanganates over here. Member "Der Alte" has done a lot of experiments in this area and what he has written on the subject is a good read.
|
Household bleach (alkaline) can, similarly, also oxidize Fe(III) to magenta-colored ferrate(VI), but again
it is practically impossible to isolate any solid sodium ferrate(VI) from it.
|
|
|
chloric1
International Hazard
Posts: 1146
Registered: 8-10-2003
Location: GroupVII of the periodic table
Member Is Offline
Mood: Stoichiometrically Balanced
|
|
@woelen I had simular problems with ammonium perchlorate and sugar mixes. They ignited very easily but burned white hot and REAL SLOW. My solution
was to mix potassium nitrate with sugar and add it to the perchlorate mix and it burns with a ROARING noise! Chlorates would be too dangerous as
additives so I recommend the nitrates as your heat booster.
Fellow molecular manipulator
|
|
|
densest
Hazard to Others
Posts: 359
Registered: 1-10-2005
Location: in the lehr
Member Is Offline
Mood: slowly warming to strain point
|
|
@chloric1 - NH4ClO4 is (in)famous for slow decomposition. Many different catalysts work to speed it up a lot: K2Cr2O7 is very effective, MnO2 is good,
even extremely finely divided Fe2O3 works some. Small perchlorate particle size is very important to fast combustion.
@woelen - I've read hypotheses that one reason KClO3 mixes ignite more easily than KClO4 is the presence of various unstable decomposition products.
How fine is your KClO4 powder? The physical shape of the aluminum powder makes a big difference in activity - flake is far more active than spheres.
It's sometimes hard to ignite KClO4/Al with a flame because it's either very reflective or transparent so radiant heat energy just bounces off. Touch
it with something above 400C and ignition is pretty much instantaneous. Yes, KClO3/P is -incredibly- sensitive, but back when I had access to red P I
tried a pinch of KClO4/P and it went off with a tap. Now, the P was old and so was the perchlorate, so contaminants like white P and chlorine oxides
could have sensitized it. Your brand new pure perchlorate may be less active 
|
|
|
ketel-one
Hazard to Self
Posts: 55
Registered: 8-9-2009
Location: Pluto (planet?)
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by woelen | | That demo is nice for showing how bleach can oxidized manganese to oxidation state +7 but it is not useful for preparation of permanganates. What you
see in that experiment is a very very dilute solution of permanganate, even a 1% solution already is nearly black. Its color is very intense. Besides
that, isolating NaMnO4 from a solution is more or less impossible if so many other impurities are present. Lookup the thread on making permanganates
over here. Member "Der Alte" has done a lot of experiments in this area and what he has written on the subject is a good read. |
Right, I don't actually need permanganates, but outside of using a little in chemistry class to test for something I forgot what I've not handled them
very much, so this is just experimentation. I love your site btw.
I assume everybody understands why KClO4 is more stable than KClO3, although I've never quite understood how KNO3 decomposes. KNO3 = KNO2 + .5O2
doesn't seem very oxidizing.
|
|
|
woelen
Super Administrator
Posts: 8027
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
KNO3 is oxidizing, because it can give up almost all of its oxygen. It goes further than KNO2. If e.g. a mix of potassium nitrate, sulphur and carbon
is ignited, then the main reaction is oxidation of carbon to CO2 (or to K2CO3, but that is the same oxidation state) and sulphur is oxidized to SO2
(and also some end up even more oxidized as K2SO4). The bigger part of the nitrogen leaves the burning mix as N2.
Formally you could write: 2KNO3 --> [K2O] + N2 + 5[O]
But keep in mind that this is just a purely formal equation. It does not happen on its own (that's why I write [] around the K2O and O), in reality,
the K2O and O ends up in K2CO3, K2SO4 and K2SO3). This formal equation does show, however, that 5 out of each 6 oxygen atoms is available for
oxidation.
[Edited on 16-9-09 by woelen]
|
|
|
Formatik
National Hazard
Posts: 927
Registered: 25-3-2008
Member Is Offline
Mood: equilibrium
|
|
| Quote: Originally posted by woelen | | I just wanted to make a pyrotechnic mix of this KClO4 with sulphur just for the fun of it (nice demo for kids), but to my surprise this mix cannot be
ignited and the kids were very disappointed. I mixed 2 parts of KClO4 with 1
part of sulphur (appr. stoichiometric ratio for KClO4 + 2S --> KCl + 2SO2). But even when some of the mix is kept on a spatula inside the flame of
an alcohol burner, this mix does not ignite! The sulphur melts and fizzles somewhat and becomes dark yellow and that's all. |
This is probably why some early references describe the perchlorate as an being inferior oxidant than chlorate, e.g. Leitfaden der
Pyrotechnik (1899) mentions it.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
