soma
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 297
Registered: 31-7-2010
Member Is Offline
Mood: No Mood
|
|
removing peroxides from thf with ferrous sulfate
I've been trying to remove peroxides from thf using ferrous sulfate. I've found several different methods recommended. E.g.:
Quote: | method 1. Peroxides in 100.0 mL of water-insoluble solvent can usually be removed by shaking with 80.0 mL of acidified ferrous sulfate solution (6.0
grams of FeSO4•7H20 / 0.60 mL conc. H2SO4 / 11.0 mL H20) in a separatory funnel or stirred vigorously in a flask until the solvent no longer gives a
positive test for peroxide; often a few minutes will suffice.
method 2. Decomposition of ether peroxides with ferrous sulfate is a commonly used method; 40g of 30% ferrous sulfate solution in water is added to
each liter of solvent. Caution is indicated since the reaction may be vigorous if the solvent contains a high concentration of peroxide.
|
I tried shaking 30g of 30% ferrous sulfate in ~2L thf without success. (I'm using quantofix indicators.) Then I tried acidifying the solution to ~pH
4. This gave better results but still doesn't seem to remove them.
Also, the quantofix instructions said to add a drop of water to the strip after the solvent has evaporated. At first the strip turns very light blue.
Then after maybe 2 minutes, it becomes dark blue. The instructions don't say how long to wait after adding the water. If I wait til the water has
dried, I get a large white area with blue around the strip borders. Would this mean the peroxide is gone?
When I test freshly distilled thf, the strip becomes very slightly blue and doesn't change after sitting. If I add water after the solvent is gone,
the strip becomes completely white.
I'm thinking of going to basic alumina.
Help appreciated.
[Edited on 10-6-2015 by soma]
[Edited on 10-6-2015 by soma]
|
|
TonyZ
Harmless
Posts: 3
Registered: 9-6-2015
Member Is Offline
Mood: No Mood
|
|
Perhaps this may help..
Burfield et al . "Deperoxidation of Ethers. A Novel Application of Self-Indicating Molecular Sieves"
Attachment: J Organic Chemistry V47 iss20 1982 [doi_10.1021_jo00141a003] Burfield - Deperoxidation of ethers.pdf (513kB) This file has been downloaded 811 times
[Edited on 10-6-2015 by TonyZ]
|
|
smaerd
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1262
Registered: 23-1-2010
Member Is Offline
Mood: hmm...
|
|
Basic Alumina works well. I relied on it solely last semester for a research project after I was met with a flask full of peroxides (visible gram
quantities). Basic alumina also drys the THF. Just use it as fast as possible, I think it removes the stabilizer.
Ferrous sulfate will work for quenching but how to recover the THF after I'm not sure. Bisulfite is similar.
TonyZ I think that only works with some molecular sieves. IE: 3A and 4A do not work.
|
|
soma
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 297
Registered: 31-7-2010
Member Is Offline
Mood: No Mood
|
|
If I remember correctly, the self indicating sieve removes the peroxide because the cobalt decomposes it. But it also produces ethanol.
|
|
soma
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 297
Registered: 31-7-2010
Member Is Offline
Mood: No Mood
|
|
Update:
I added more water to the THF/FeIISO4/H2SO4 mix. THF is fairly soluble in water.
The addition of more water seems to have caused the removal of the peroxides. I then distilled off the THF. I'm going to test the remaining water to
see if there's any peroxides in it.
|
|
soma
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 297
Registered: 31-7-2010
Member Is Offline
Mood: No Mood
|
|
Tested the remaining water after distilling.
No peroxides!
Couldn't get rid of them no matter how much shaking of the FeSO4/H2SO4/(small amount of)water mix.
|
|