Difference between revisions of "Benzene"

Revision as of 10:16, 15 July 2017

Benzene

Freshly distilled benzene
Structure of benzene
Names
IUPAC name Benzene
Preferred IUPAC name Benzene
Systematic IUPAC name Benzene
Other names Benzol Cyclohexatriene Phene Phenyl hydride Pyrobenzole
Properties
Chemical formula	C6H6
Molar mass	78.11 g/mol
Appearance	Colorless liquid
Odor	Sweet, aromatic
Density	0.8765(20) g/cm3
Melting point	5.53 °C (41.95 °F; 278.68 K)
Boiling point	80.1 °C (176.2 °F; 353.2 K)
Solubility in water	1.53 g/L (0 °C) 1.81 g/L (9 °C) 1.79 g/L (15 °C) 1.84 g/L (30 °C) 2.26 g/L (61 °C) 3.94 g/L (100 °C) 21.7 g/kg (200 °C, 6.5 MPa) 17.8 g/kg (200 °C, 40 MPa)
Solubility	Miscible with glacial acetic acid, acetone, carbon disulfide, CCl4, chloroform, diethyl ether, toluene, xylene Immiscible with cyclohexane, heptane, hexane, pentane
Solubility in diethylene glycol	52 g/100 g (20 °C)
Solubility in ethylene glycol	5.83 g/100 g (20 °C) 6.61 g/100 g (40 °C) 7.61 g/100 g (60 °C)
Vapor pressure	12.7 kPa (25 °C) 24.4 kPa (40 °C) 181 kPa (100 °C)
Thermochemistry
Std molar entropy (So298)	173.26 J·mol-1·K-1
Std enthalpy of formation (ΔfHo298)	48.7 kJ/mol
Hazards
Safety data sheet	Sigma-Aldrich
Flash point	−11.63 °C (11.07 °F; 261.52 K)
Lethal dose or concentration (LD, LC):
LD50 (Median dose)	930 mg/kg (rat, oral)
Related compounds
Related compounds	Toluene
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
Infobox references

Benzene is an organic chemical compound with the molecular formula C₆H₆. It is the simplest aromatic hydrocarbon.

Properties

Chemical

Benzene's aromatic ring is involved in complex reactions. At standard conditions, benzene is not very reactive, but it can react with halogens, alkenes, haloalkenes, organic acid anhydrides in the presence of a Lewis acid, (anhydrous aluminium chloride, iron(III) chloride).

The nitration of benzene occurs with a solution of concentrated sulfuric acid and nitric acid.

Physical

Benzene is a colorless and highly flammable liquid with a sweet smell. It is not miscible in water, but it is in many other organic solvents, such as haloalkanes, ethers, ethanol. Benzene will dissolve certain plastic materials, such as polystyrene. It is also a good solvent for sulfur.

Availability

Benzene is available at organic chemical suppliers, but because of its environmental hazards it tends to be somewhat overpriced. In most countries it has been phased out from most products and it's also hard to find as a pure reagent.

Preparation

Benzene can be prepared from the decarboxylation of sodium benzoate with sodium hydroxide, by heating the mixture and condensing the resulting benzene. You can also use calcium oxide and benzoic acid. The decarboxylation method tends to produce biphenyl as well, giving the condensate a reddish color. Distillation will remove any impurities.

Benzene can also be produced by the pyrolysis of plastic (usually polyethylene) and sodium hydroxide. This method produces benzene along with other hydrocarbons, so fractional distillation might be required.^[1]

Best plastic material however is polyethylene terephtalate (PET), which is readily available. You will first need to hydrolyze it with sodium hydroxide in a high boiling point solvent, such as in ethylene glycol, which gives sodium terephtalate, which can be decarboxylated to benzene using sodium hydroxide. The resulting product is an orange-reddish liquid with lots of basic water, which can be separated by using a separatory funnel, followed by distillation. The yield from this reaction however, is lower than that from sodium benzoate (~15% compared to 45-60%), and plenty of terephtalate can get charred if the temperature is too high. Lots of side products are produced, which may clog the distillation apparatus.^[2][3][4]

CHROMIUM has published a pdf on Sciencemadness library about many methods of synthesizing benzene, gathered from various members.^[5]

Projects

• Napalm
• Toluene synthesis
• Chlorobenzene synthesis
• Nitrobenzene synthesis
• Sulfur extraction

Handling

Safety

Benzene is a strong carcinogen, so work must be performed in a fume hood or outside. Protection gear is required, as it can penetrate skin. If possible, use toluene or xylene, which are cheaper, safer and more widely available.

Storage

Benzene must be stored in closed bottles, away from any source of heat.

Disposal

Benzene can be destroyed using Fenton's reagent. If the oxidation is incomplete, phenol and biphenyl will result. If too much benzene is added, the resulting gasses will aerosolize some of the benzene, which is dangerous in an enclosed area, carrying both a fire/explosion hazard as well as inhaling dangerous and carcinogenic benzene fumes. This inconvenience can be reduced by adding the benzene dropwise or bubbling (non-flammable) gas-carried benzene through a gas diffusing stone through the Fenton solution to limit vapor escape. Either perform the neutralization in a fumehood, or outside, preferably the latter. Photochemical neutralization, with the aid of a UV lamp will improve the yield of the oxidation process.

Benzene can also be burned, but this will give off lots of soot, carbon monoxide, other aromatics and unburnt benzene vapors, unless it's done in a waste incinerator. If you really want to do this, do it outside, away from people.

References

1. ↑ http://www.youtube.com/watch?v=JhUxaNesnxs
2. ↑ https://www.youtube.com/watch?v=JuvczYeM3kk
3. ↑ https://www.youtube.com/watch?v=uRTrjaAb4NA
4. ↑ https://www.youtube.com/watch?v=Zh0RK0an8f4
5. ↑ http://www.sciencemadness.org/member_publications/benzene_production.pdf

Relevant Sciencemadness threads

• Benzene synthesis
• Benzene from PET