Yttrium2
Perpetual Question Machine
Posts: 1104
Registered: 7-2-2015
Member Is Offline
|
|
Test Tube Holder
Again, I'm making a thread in regards to: How do I make a test tube holder,
the parameters; 1) There are 6 test tubes.
2) The holes are evenly spaces
3) There is a 1" margin on each side
Question: How mathematically can we determine how much space should go in between each hole?
Also
Question2: How could we determine the spacing that would need to take place to evenly space the tubes within a circle?
-- I have a top to a peanut butter jar that I figured I could use as a test tube holder. -- Not made out of gopher wood, or anything like that...
[Edited on 10/12/2018 by Yttrium2]
|
|
|
Sulaiman
International Hazard
Posts: 3698
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Sketch the linear and circular test tube racks with letters to represent dimensions and the mathematics will follow.
|
|
|
Yttrium2
Perpetual Question Machine
Posts: 1104
Registered: 7-2-2015
Member Is Offline
|
|
nevermind, their is an abacus beside me. I'll use it to see how many spokes there are and then from there deconstruct what they used to measure, and
how, mathematically, they found out how much distance to space the holes.
|
|
|
Mr. Rogers
Hazard to Others
Posts: 184
Registered: 30-10-2017
Location: Ammonia Avenue
Member Is Offline
Mood: No Mood
|
|
You're overthinking this maybe. A drill press and a ruler is all you need to get the two haves as identical as they can be.
|
|
|
Abromination
Hazard to Others
Posts: 432
Registered: 10-7-2018
Location: Alaska
Member Is Offline
Mood: 1,4 tar
|
|
I use a spot plate that happens to fit the diameter of my test tubes. It should fit most test tubes, it can be found on homesciencetools.com. It
should be the site's only plastic spot plate.
List of materials made by ScienceMadness.org users:
https://docs.google.com/spreadsheets/d/1nmJ8uq-h4IkXPxD5svnT...
--------------------------------
Elements Collected: H, Li, B, C, N, O, Mg, Al, Si, P, S, Fe, Ni, Cu, Zn, Ag, I, Au, Pb, Bi, Am
Last Acquired: B
Next: Na
-------------- |
|
|
Elrik
Hazard to Self
Posts: 52
Registered: 1-9-2018
Member Is Offline
|
|
Quote: Originally posted by Mr. Rogers  | | You're overthinking this maybe. A drill press and a ruler is all you need to get the two haves as identical as they can be. |
As much as I believe in retaining a proficiency in trigonometry, I think Mr. Rogers is right. If your making a holder from cheap
materials then a ruler for rows or a printed picture of cyclohexane or cyclopentane to guide a circle is more than good enough. I made these two with
those methods and they came out fine, even if they do have a variance of ±1 mm 
If you want more complexity, just remember than your right triangles angle is Sin-1(opp/hyp) or Cos-1(adj/hyp) or
Tan-1(opp/adj)
Soh Cah Toa 
|
|
|
DrP
National Hazard
Posts: 625
Registered: 28-9-2005
Member Is Offline
Mood: exothermic
|
|
These are my 3 favourite test tube holders: https://st3.depositphotos.com/10654668/14428/i/1600/depositp...
Also up there as a quality holder: https://thumbs.dreamstime.com/z/young-woman-holding-test-tub...
\"It\'s a man\'s obligation to stick his boneration in a women\'s separation; this sort of penetration will increase the population of the younger
generation\" - Eric Cartman
|
|
|
CharlieA
National Hazard
Posts: 646
Registered: 11-8-2015
Location: Missouri, USA
Member Is Offline
Mood: No Mood
|
|
Dr. P, Those are the best yet!
...but I think you have too much time on your hands!
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
