Radium212
Hazard to Self
Posts: 85
Registered: 26-6-2017
Member Is Offline
Mood: Pyrophoric.
|
|
Is this a good Geiger counter cicuit?
https://photos.google.com/photo/AF1QipPNAjc2LYZt1TUiDYWsPC3L... Is this a good circuit for a Geiger counter with a range selector? Will it work?
|
|
|
aga
Forum Drunkard
Posts: 7030
Registered: 25-3-2014
Member Is Offline
|
|
Hints and tips: make sure the link works or nobody can see what you're referring to.
|
|
|
Radium212
Hazard to Self
Posts: 85
Registered: 26-6-2017
Member Is Offline
Mood: Pyrophoric.
|
|
Works perfectly fine for me. Just to state, it's the circuit itself that's important, not the component values.
|
|
|
Cryolite.
Hazard to Others
Posts: 269
Registered: 28-6-2016
Location: CA
Member Is Offline
Mood: No Mood
|
|
Broken for me too.
|
|
|
unionised
International Hazard
Posts: 5126
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Doesn't work for me; asks for log-in details.
That's hardly the point.
If it doesn't work for some people then it's the OP's responsibility to make it work, rather than saying "it works for me"
[Edited on 27-12-17 by unionised]
|
|
|
Texium
|
Thread Moved
27-12-2017 at 17:40 |
Radium212
Hazard to Self
Posts: 85
Registered: 26-6-2017
Member Is Offline
Mood: Pyrophoric.
|
|
Ok, sorry I didn't know Google photos worked like that, my error, sorry. But to describe it, it's a simple 400V power supply, which I know works. The
part which I want to know about is the range selector I designed. It's just a rotary switch with the main pole connected to the tube cathode, then on
the three other poles, a 10 Ohm, 1k Ohm, and 10k Ohm resistor. It allows you to select the measurement range. All resistors go to the meter. Does that
seem sensible.
|
|
|
aga
Forum Drunkard
Posts: 7030
Registered: 25-3-2014
Member Is Offline
|
|
Silly question, and failed post, entirely, especially for a chemistry forum that does not specialise in electronics.
If it were electronics, the specifics of the particular geiger tube would be needed to make any judgement at all.
Google 'Geiger Counter Circuit'
Also look on Ebay - sometimes just buying the thing is cheaper than making one.
|
|
|
phlogiston
International Hazard
Posts: 1379
Registered: 26-4-2008
Location: Neon Thorium Erbium Lanthanum Neodymium Sulphur
Member Is Offline
Mood: pyrophoric
|
|
You should really post the circuit. I don't think we need the datasheet for the geiger tube itself, but your description of the circuit you intend to
build is not clear enough I am afraid. I can speculate and guess a bit, but we can have a focused, efficient discussion if you could share the
circuit.
[Edited on 30-12-2017 by phlogiston]
-----
"If a rocket goes up, who cares where it comes down, that's not my concern said Wernher von Braun" - Tom Lehrer |
|
|
NEMO-Chemistry
International Hazard
Posts: 1559
Registered: 29-5-2016
Location: UK
Member Is Offline
Mood: No Mood
|
|
Make sure the switch is rated for 400V, what W are the resistors and much power they need to dissipate?
|
|
|
Radium212
Hazard to Self
Posts: 85
Registered: 26-6-2017
Member Is Offline
Mood: Pyrophoric.
|
|
phlogiston, sorry, I can't find a way to share it. I have gone over it again though, and it seems fine. I'll breadboard it and see how it works then.
|
|
|
Harristotle
Hazard to Others
Posts: 138
Registered: 30-10-2011
Location: Tinkerville
Member Is Offline
Mood: I tink therefore I am
|
|
You remind me of a 1000 volt circuit I was making for a photomultiplier tube, a while ago.
I discovered that my breadboard was rated to under 250 volts.
It was a character, knowledge and vocabulary building experience! I only discovered the error of my ways late at night when I turned out the light
after days of replacing this, that and the other.
May I suggest that often breadboards are unsuitable for HV work.
Cheers,
H.
|
|
|
Radium212
Hazard to Self
Posts: 85
Registered: 26-6-2017
Member Is Offline
Mood: Pyrophoric.
|
|
Ok, thanks for the tip! I have tons of components so can afford a few failed prototypes.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
