Hilski
Hazard to Others
Posts: 197
Registered: 13-9-2006
Member Is Offline
Mood: No Mood
|
|
Question about cold traps
I have a Gast lab vacuum pump, which has carbon fiber vanes, and uses a separate siphon type oiler, instead of actually having oil inside the pump. I
plan to use the pump to vac distill things like benzaldehyde and other non-corrosive substances. I want to make a basic vacuum trap to prevent damage
to the pump if some non compressable were to get into the suction line. But what I wanted to ask was if I really need to use a cold trap? Like I
said earlier, there is no oil in the pump to contaminate, and I will not be using the pump to distill corrosive liquids.
This pump is made specifically for this type of application, and the literature makes no mention of using a trap other than the filters that came with
t he pump.
Here's a picture of the pump showing the oiler plumbed into an intake port on the side.
Thanks in advance.
[Edited on 9-1-2007 by Hilski]
|
|
|
matei
Hazard to Others
Posts: 205
Registered: 16-9-2006
Member Is Offline
Mood: No Mood
|
|
Hilski, I think that kind of pump doesn't require a solvent trap, because from what I can tell from thet picture it does't make a vacuum better than
maybe 10 torr. At that pressure the quantity of solvent which can get into the pump is small. However when you distill something you must use an
efficient condenser.
Cold traps are used only for rotary oil pumps when you want to achieve a vacuum of 10e-2 torr.
For a rotary oil pump a good alternative for a cold trap would be to use 2 traps connected in series, one filled with activated carbon and one with
KOH pellets, but in this case the vacuum would be 1 torr or so.
|
|
|
Hilski
Hazard to Others
Posts: 197
Registered: 13-9-2006
Member Is Offline
Mood: No Mood
|
|
| Quote: | | Cold traps are used only for rotary oil pumps when you want to achieve a vacuum of 10e-2 torr. |
OK. That's good to know.
For some reason I was thinking that you were pretty much always supposed to have one, but like you said, my pump doesn't go to less than 1 torr.
This pump is good for about 27 inches of mercury which, if I remember correctly is somewhere around 60 - 70 torr.
Thanks
|
|
|
Maya
Hazard to Others
Posts: 263
Registered: 3-10-2006
Location: Mercury
Member Is Offline
Mood: molten
|
|
You might as well use a water aspirator which can go as low as 15-20 torr.
Otherwise , if looking for a cold trap then you may want to invest in a SAVANT, You can sometimes pick them up fairly cheap from a famous place to get
'em. I got two , one for $9 the other for $50 and one works down to -86 deg and the other one doesn't 
\"Prefiero ser yo extranjero en otras patrias, a serlo en la mia\"
|
|
|
Hilski
Hazard to Others
Posts: 197
Registered: 13-9-2006
Member Is Offline
Mood: No Mood
|
|
| Quote: | | You might as well use a water aspirator which can go as low as 15-20 torr. |
If I had a aspirator vacuum station built, I would definitely use it. But since I don't, I will be using the pump.
But for some reason, I find it hard to believe that an aspirator can pull more than the 27 inches of mercury that this (or any good vacuum pump) can
pull. I've worked with all sorts of vacuum pumps in refrigeration, and even the best of them can't get much better than about 28 - 29 in Hg. The
only system I've used that can get very close to 30 inHg had a huge diesel driven compressor that was used to pull a vacuum on the high side of the
system before shutting it down.
|
|
|
matei
Hazard to Others
Posts: 205
Registered: 16-9-2006
Member Is Offline
Mood: No Mood
|
|
| Quote: | Originally posted by Maya
You might as well use a water aspirator which can go as low as 15-20 torr.
|
I think 15-20 torr is the theoretical limit which a water aspirator can achieve (that is the vapour pressure of water at 10 deg. C). In practice I
don't think they go below 40-50 torr.
|
|
|
MargaretThatcher
Hazard to Self
Posts: 54
Registered: 21-3-2006
Location: Tonga
Member Is Offline
Mood: Handbagging
|
|
| Quote: | Originally posted by matei
| Quote: | Originally posted by Maya
You might as well use a water aspirator which can go as low as 15-20 torr.
|
I think 15-20 torr is the theoretical limit which a water aspirator can achieve (that is the vapour pressure of water at 10 deg. C). In practice I
don't think they go below 40-50 torr. |
Not so. Most lab. water-jet pumps will pull down to the vapour pressure of water. Even homemade ones get down that far. Just float ice in a
recirculating setup and you will achieve a really good pressure.
The reformative effect of punishment is a belief that dies hard, I think, because it is so satisfying to our sadistic impulses. - Bertrand Russell
|
|
|
Maya
Hazard to Others
Posts: 263
Registered: 3-10-2006
Location: Mercury
Member Is Offline
Mood: molten
|
|
If I had a aspirator vacuum station built, I would definitely use it. But since I don't, I will be using the pump.
But for some reason, I find it hard to believe that an aspirator can pull more than the 27 inches of mercury that this (or any good vacuum pump) can
pull. I've worked with all sorts of vacuum pumps in refrigeration, and even the best of them can't get much better than about 28 - 29 in Hg. The only
system I've used that can get very close to 30 inHg had a huge diesel driven compressor that was used to pull a vacuum on the high side of the system
before shutting it down. >>>>>>>>>
I've got down to exactly 15-17 torr measured with a high precision homemade mercury manometer which was precise to 1 mm. I didn't even have to cool
it below 10 deg
I think most pumps will do better than 28-29 in Hg, not putting your pump down. Maybe you should check the vanes or oil for cleanliness or
contamination which is not letting it achieve a better vacumm?
\"Prefiero ser yo extranjero en otras patrias, a serlo en la mia\"
|
|
|
Chemist514
Hazard to Self
Posts: 68
Registered: 12-5-2006
Member Is Offline
Mood: No Mood
|
|
| Quote: | Originally posted by Hilski
I have a Gast lab vacuum pump, which has carbon fiber vanes, and uses a separate siphon type oiler, instead of actually having oil inside the pump. I
plan to use the pump to vac distill things like benzaldehyde and other non-corrosive substances. I want to make a basic vacuum trap to prevent damage
to the pump if some non compressable were to get into the suction line. But what I wanted to ask was if I really need to use a cold trap? Like I
said earlier, there is no oil in the pump to contaminate, and I will not be using the pump to distill corrosive liquids.
This pump is made specifically for this type of application, and the literature makes no mention of using a trap other than the filters that came with
t he pump.
Here's a picture of the pump showing the oiler plumbed into an intake port on the side.
Thanks in advance.
[Edited on 9-1-2007 by Hilski] |
This site has amazing info on vacuum...
www.belljar.net
and there is this guy who is amateur-aware so to speak...
http://www.ee.ualberta.ca/~schmaus/vacf/index.html
The very best of luck! I'm having a blast with my donated ED 35 High Vacuum pump, but really must locate a real dessicator now. You happen to know
anything about an Alcatel CFA 212 pirani/penning monitor? I have one of those but no probes... always the case. :< (I'd love to get it working,
reads down to 10-7.
again, the very best of luck to ya.
|
|
|
chemrox
International Hazard
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
| Quote: | Originally posted by Maya
You might as well use a water aspirator which can go as low as 15-20 torr.
Otherwise , if looking for a cold trap then you may want to invest in a SAVANT, You can sometimes pick them up fairly cheap from a famous place to get
'em. I got two ,
Could you be a little more specific here? Or send me a U2U? Thanks |
|
|
|
chemrox
International Hazard
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
cold trap
I just flashed off a liter of xylene using and inefficient trap at around 30mm Hg and messed up my pump oil big time. I keep a gallon of oil on
hand. I need a better trap. Improvising with a flask and ice bath didn't do it and I need to do some plumbing before I can use my aspirator. That
Buchi coil condenser just isn't that efficient.
|
|
|
Maya
Hazard to Others
Posts: 263
Registered: 3-10-2006
Location: Mercury
Member Is Offline
Mood: molten
|
|
Try using a regulator with that rotovap, sometimes you get too much vacuum at first and solvent flashes over, I don't think rotovaps are suppossed to
be used less than 10 torr, at least not with large quantities of solvent
\"Prefiero ser yo extranjero en otras patrias, a serlo en la mia\"
|
|
|
Hilski
Hazard to Others
Posts: 197
Registered: 13-9-2006
Member Is Offline
Mood: No Mood
|
|
| Quote: | | I think most pumps will do better than 28-29 in Hg, not putting your pump down. Maybe you should check the vanes or oil for cleanliness or
contamination which is not letting it achieve a better vacumm? |
I didn't know it at the time I bought the pump, but despite the fact that this pump is designed specifically for laboratory use (distillations,
filtering etc) it is only good for 26 inches of mercury (about 100 torr) right out of the factory. The pump is distributed by Fisher scientific, and
is stupid expensive if purchased new (I only paid 50 bucks) so it doesn't make a whole lot of sense that it is so limited. I did disassemble the pump
and clean it, but everything looked great. The thing hadn't been used much at all.
Granted, one can do a lot with 100 torr, but I'd much rather be a lot lower. So, I decided to make an aspirator like the one on Frogfot's website.
I was able to get to under 30 torr with the homemade jet pump, and with some tweaking I think I can get more out of it. This thing is almost too good
to be true, since it cost me all of 0$ to make. Now I just need to get a spa pump so I can build a recirculating system, instead of wasting so much
water.
| Quote: | | The very best of luck! |
Thanks. I for one need all the luck I can get.
Hilski
[Edited on 19-1-2007 by Hilski]
\"They that can give up essential liberty
to obtain a little temporary safety
deserve neither liberty nor safety. \"
- Benjamin Franklin
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
