| Pages:
1
2
3
..
8 |
Organikum
resurrected
Posts: 2337
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: frustrated
|
|
oleum & SO3
Here we go
HARDCORE:
Oleum, smoking H2SO4, 50%SO3 in H2SO4, SO3
First I suggest everyone who wants to tinker with this may inform himself on the truely existing dangers of these compounds. They are not nasty - they
are dangerous!
Madscientist passed H2SO4 over MgSO4 for oleum (did this really work?) he wrote and in more than one synth SO3 was asked for (acetic anhydride for
example, nitric acid).
So here is a doable way to produce oleum and SO3:
- Ferrous sulfate septahydrate is made from iron (filings/steelwool) and H2SO4.
- Ferrous sulfate septahydrate dehydrates completely by heating >300°C.
- Anhydrous Ferrous sulfate decomposes to SO3 at 480°C and can be condensed to oleum (or the SO3 can be directly used of course).
If the oleum is what one is after it should be possible to decompose and condense in the same vessel without extern apparati necessary. The vessel has
to be big and strong enough - thats understood.
|
|
|
madscientist
National Hazard
Posts: 962
Registered: 19-5-2002
Location: American Midwest
Member Is Offline
Mood: pyrophoric
|
|
Organikum: I think my oleum attempt from long ago didn't actually work - I probably just thought it did (considering my relative ignorance back
then, and the fact that I made way too many assumptions).
I weep at the sight of flaming acetic anhydride.
|
|
|
Organikum
resurrected
Posts: 2337
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: frustrated
|
|
xoo1246: Yes me too! The howto on the ferreous was only included for completeness and the sure to come question on it. Sooner or later.......
Madscientist: No problem for me. My complete errors and selfcaused mishappenings will be published soon. Five volumes. Open end. Working title:
"Oh! Oh! Oh! - Oh shit!" Probably the "shit" has to be removed so.......
....oh, oh, oh.
|
|
|
I am a fish
undersea enforcer
Posts: 600
Registered: 16-1-2003
Location: Bath, United Kingdom
Member Is Offline
Mood: Ichthyoidal
|
|
| Quote: | Originally posted by Organikum
- Ferrous sulfate septahydrate is made from iron (filings/steelwool) and H2SO4.
- Ferrous sulfate septahydrate dehydrates completely by heating >300°C.
- Anhydrous Ferrous sulfate decomposes to SO3 at 480°C and can be condensed to oleum (or the SO3 can be directly used of course).
|
Heating the ferrous sulphate must be done in an oxygen free atmosphere, otherwise it will oxidise into the ferric state.
Another good source of ferrous sulphate is 'Iron Mordant', whch is available from all good dyeing suppliers.
1f `/0u (4|\\| |234d 7|-|15, `/0u |234||`/ |\\|33d 70 937 0u7 /\\/\\0|23.
|
|
|
Organikum
resurrected
Posts: 2337
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: frustrated
|
|
You are right, fish you are!
The setup has to be closed against the outside what should be understood for the unhealthy properties of SO3 alone. For the ease of availability of
the reactands I would say that it´s not necessary to purge with an inert gas, but it´s easier to sacrifice a part of the ferrous sulfate to the
oxygen inside. There should be enough left to be converted to SO3 - the efficiency of these rather old and raw methods isn´t very good anyways I
believe.
Exactly for such critics it got posted. Thanks fish you are!
[Edited on 26-5-2003 by Organikum]
|
|
|
Microtek
National Hazard
Posts: 871
Registered: 23-9-2002
Member Is Offline
Mood: No Mood
|
|
Industrially, the SO3 is absorbed in circulating concentrated H2SO4 which is then diluted with water. This is done to attenuate the violence of
reacting SO3 directly with water.
|
|
|
vulture
Forum Gatekeeper
Posts: 3330
Registered: 25-5-2002
Location: France
Member Is Offline
Mood: No Mood
|
|
Why not use CuSO4? That can't be oxidized any further.
One shouldn't accept or resort to the mutilation of science to appease the mentally impaired.
|
|
|
Organikum
resurrected
Posts: 2337
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: frustrated
|
|
higher temperatures?
CuSO4 starts to decomposes at a temperatures of 560°C whereby FeSO4 is completely decomposed at 480°C. Thats how I understood it at least. In the
original process costs will have been a factor also - I didn´t invent this, I just don´t know where this was taken from, if I knew it, I would have
named it.
CuSO4 maybe worth a try, also I can´t see any advantages. as the FeSO4 scrubbing the oxygen seems to me favorable.
The humidity in the reactor should be driven out during heating the FeSO4 for becoming anhydrous what should be done in the same vessel anyways. I
propose that vessel and FeSO4 will be in the same state of anhydrous condition so.
(Ah! The beauty of strong causal logic!)
btw. this is a concept for discussion, not a complete running process by now. So the formulation: "Why don´t you use..." is inadequate
here.
|
|
|
a_bab
Hazard to Others
Posts: 458
Registered: 15-9-2002
Member Is Offline
Mood: Angry !!!!!111111...2?!
|
|
What about heating H2SO4 ? The white fumes are mainly because of SO3 IIRC.
|
|
|
rikkitikkitavi
Hazard to Others
Posts: 192
Registered: 17-6-2002
Member Is Offline
Mood: No Mood
|
|
no, a_bab, the white fumes of heated (boiling ) sulfuric acid is just sulfuric acid droplets. If H2SO4 is heated , it will split to SO3+ H2O at high
temperatures and the SO3 will decompose into SO2 and O2 at these temperatures.
Better than FeSO4 is Fe2(SO4)3 since +3 ions decomposes into SO3+SO2 at lower tempertures. Expect a large loss of SO3 due to eq. SO3 = SO2 + 1/2 SO2
/rickard
|
|
|
ziqquratu
Hazard to Others
Posts: 385
Registered: 15-11-2002
Member Is Offline
Mood: No Mood
|
|
I think that heating Sodim bisulfate may well work... I'm not exactly sure of the temperatures, but I do know they're accessable to a gas
flame. If I remember, you dry the bisulfate in an oven, then heat it over a gas flame, and water gets produced. You keep the heat so that water is
just getting produced, and you're getting solid sodium pyrosulfate, until water stops forming. Then crank up the heat to decompose the sodium
pyrosulfate and get sodium sulfate and sulfur trioxide. then the best thing to do is dissolve the gas in cooled, concentrated H2SO4. It can work if
you use a distillation setup - change flasks between the water production and the decomposition of the solid. Although I dont think you'd want
to be too attached to the flask that you're heating - it may suffer some permanent damage if you're not careful. I dont actually have a
reference for this, mind you - I just remember seeing it somewhere some time ago and thinking "hmm... must try this one day"... never got
around to it... must remedy that. Oh, by the way, Sodium Bisulfate is commonly used for raising the pH of swimming pools... very cheap and easy to
find
|
|
|
a_bab
Hazard to Others
Posts: 458
Registered: 15-9-2002
Member Is Offline
Mood: Angry !!!!!111111...2?!
|
|
Yes rikkitikkitavi, you are right. I was confused because of the lab method wich is using oleum to get SO3.
You are right aswell ziqquratu, a simple method could be heating NaHSO4 or KHSO4. The reaction will be in two stages, one at 200-300 degrees C, when
the alkali pyrosulfate is formed, and then the other at 500 degrees C when SO3 is formed because of the thermal decomposition of the pyrosulfate.
The reactions are:
1. 2NaHSO4 --->Na2S2O7+H2O
2. Na2S2O7---->Na2SO4+SO3
[Edited on 28-5-2003 by a_bab]
|
|
|
vulture
Forum Gatekeeper
Posts: 3330
Registered: 25-5-2002
Location: France
Member Is Offline
Mood: No Mood
|
|
NaHSO4 for raising the pH?
HSO4- has a pKa of 1,92 which means it will behave like an acid in solution. Especially in diluted solution.
One shouldn't accept or resort to the mutilation of science to appease the mentally impaired.
|
|
|
ziqquratu
Hazard to Others
Posts: 385
Registered: 15-11-2002
Member Is Offline
Mood: No Mood
|
|
Oops!!
Sorry, I didnt see that one!! Sodium bisulfate makes pH lower!! I'd have simply edited my above post, but then anyone reading what vulture
wrote would have no idea what was going on!! Thanks for pointing that one out
|
|
|
Organikum
resurrected
Posts: 2337
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: frustrated
|
|
a short resumee
- by principle the process will work and includes no dangers like sudden decomposition (explosion) which would render it useless for the amateur
experimenter.
- precautions: drying the used apparatus which has to be a enclosed one.
Also the apparatus must be VERY acid resistant. Ceramics, porcellain, clay, not glass or metal (to stay on the safe side)
- Fumehood or outside with fan at least.
- Other starting compounds than FeSO4 seem to be possible.
Please correct me if I am wrong
thanks
ORG
Next step would be a layout for the apparatus - I thought on a modified KLIPP principle for keeping it small.
[Edited on 29-5-2003 by Organikum]
|
|
|
KABOOOM(pyrojustforfun)
Hazard to Others
Posts: 254
Registered: 12-10-2002
Location: Iran (pseudoislamic dictatorship of)
Member Is Offline
Mood: exuviating!
|
|
destructive distillation of green vitriol(FeSO<sub>4</sub>.7H<sub>2</sub>O) is a very traditional way of making
H<sub>2</sub>SO<sub>4</sub> and was first done by hayyan (don't know its English spelling)
Organikum! are you sure the 480°C is the decomosition point for ferrous sulfate? it is the exact temp for ferric too.
is ferric hydrogen sulfate, anhydrous or hydrate? if it is anhydrous or can be dehydrated at a lower temp than its decompositin point, it's
possible to make oleom without need of conc sulfuric acid! u simply add dilute H<sub>2</sub>SO<sub>4</sub> to ferric
sulfate/oxide/hydroxide.. recrystalize the salt and distill off.
2Fe(HSO<sub>4</sub><sub>3</sub> =>
Fe<sub>2</sub>O<sub>3</sub> + 3H<sub>2</sub>S<sub>2</sub>O<sub>7</sub>
it may lose H<sub>2</sub>O forming pyrosulfate first, (but my sence doesn't approve it.)
the pyrosulfate method is great for those who distill their own nitric acid. just dilute the wast acid => recrysalize the alkali metal hydrogen
sulfate.
[Edited on 2-9-2003 by KABOOOM(pyrojustforfun)]
|
|
|
BromicAcid
International Hazard
Posts: 3248
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
We don't have a thread started for the reactions of SO3 but I figured this thread would do since I don't feel it necessary to start a new
one.
"Sulfur trioxide reacts with KClO3 to form K2S3O10 and a red product assumed to be (ClO2)2S3O10 (mp 75C)" The red product has a violent
decomposition at 100C. An anologous reaction occurs with KClO4.
On topic it appears that the decomposition temperature of ferric sulfate is significantly higher then 480C. Here are two passages from the Complete
Tretise on Inorganic Chemistry that are relevent:
"The yield of fuming acid is poor because the temp. of dissociation of ferric sulfate is so high that a large proportion of of sulfur trioxide is
decomposed at the same time."
And relating to that: "The dissociation pressure of the trioxide from ferric sulfate was found by G. Keppeler and J. d'Ans to be only 15mm.
at 640C so that the temp of the retorts must be much higher then this."
Other interesting information relating to things said upthread:
"P.G. Prelier proposed to heat the alkali or alkaline earth sulfates with sulfuric acid to form the hydrosulfate, and to distill the water from
the hydrosulfate, and the fuming acid or sulfur trioxide from the pyrosulfate. R.W. Wallace proposed a modification of this process; adn W. Wolters
said that the liberation of sulfur trioxide from the pyrosulfate occurs at a lower temp if some magnesium sulfate is present. This means that less
sulfur trioxide is dissociated. W. Wolters also proposed to heat the pyrosulfate with anhydrous sulfuric acid so as to distill off the sulfur
trioxide:
N2S2O7 + H2SO4 ---> 2NaHSO4 + SO3
A.M. Leon proposed to electrolyze the monohydrated sulfuric acid so that the water decomposes into hydrogen and oxygen, and the resulting sulfur
trioxide dissolved in the electrolyte to form the fuming acid."
As for the last part though, I doubt graphite would survive and I would have to guess the electrodes would have to be made of something like Pt.
|
|
|
S.C. Wack
bibliomaster
Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline
Mood: Enhanced
|
|
Wolters' patent with MgSO4: DE6091. With H2SO4: DE12295. Very uninformative. I think Wallace had a temp of 600C going.
GB237243 mentions a temp of 750-780 for the ferric sulfate deal.
GB 124988 is about sawdust and bisulfate.
In US342784 and 342785, clay and gypsum give cement and SO3. Like most thermal methods, expect at least half of the S as SO2. I think I saw this in
Kirk-Othmer somewhere, but that doesn't mean it works! And US2528103 bluntly says so, but doesn't even get Cummings' name right.
Anyways, it is supposed to be an improvement. I've seen both of Cummings' pats on espacenet before, but (no surprise) I was just there and
they say that they don't exist. Of course uspto.gov says that they do.
|
|
|
Proteios
Hazard to Others
Posts: 109
Registered: 7-3-2004
Member Is Offline
Mood: No Mood
|
|
oks....my contribution.....
1) high temperature control without some reasonable kit is a bitch.
2) the temperatures you are talking are getting close to the softening point of pyrex (600-700 C).....
All my attempts to decomp. FeSO4 CuSO4 as a teeny failed. I only used glass.
Now with much more real experience:
I think your best bet is a metal kit. Air and oxidation of the FeII i think is a limited worry, given that at the temperature you are talking the SO3
= SO2 n O2 equilibrium will estabilsh fairly quickly. Plus you have to get the O2 into the matrix of the solid (rates)
How to best do this is really dependant upon all sort of unknown rates, but my guess is you will be best off with a straight tube, Copper i think is
good and easily available. Use an air carrier, modest airflow (fish tank pump). This will get the SO3 away more quickly from the hot surface where
decomposition/equilibration will occur. SO3 is a pretty good gas at even modest temperatures, consdense on cold glassware. How quickly SO3 eats the
tube is also a worry, but also another good reason for using a carrier gas. It will dilute the SO3, it will cool the SO3 and it will move the SO3
away from the metal surface more quickly.
-there are a lot of guesses, assumptions and opinion here!!!!!!!
I also FAILED MANY times to make SO3 from SO2 and air, using a V 2O5 catalyst, with only the most primative of supports. Temperature control was a
real bitch (propane gas torch), as was getting SO2 dry enough.
I only once succeded at making SO3, and that was at school (everything else was done at home), using an SO2 cylinder and a platinumised wool catalyst.
Using relatively low heat (bearly off sooty flame on a bunsen) over a period of maybe 1 hr, I made maybe 2-5g of SO3 as a crytaline solid that
readily melted with bodyheat.
In summary, probably a bent Cu tube, FeSO4 in bottom, air carrirer, roast to red heat with gas torch, have faith, that even though you cant see whats
happening, it will work!
alternatively, maybe a pretty determined piece of kit for the SO2 oxidation!
|
|
|
chemoleo
Biochemicus Energeticus
Posts: 3005
Registered: 23-7-2003
Location: England Germany
Member Is Offline
Mood: crystalline
|
|
Na2S2O8
A long time ago I generated SO3 from sodium persulphate, which I obtained from conrad.de, and which I coincidentially wanted to use for copper
etching.
I just heated the persulphate in a testtube, and melted very quickly. Upon heating a bit further, VAST amounts of SO3 were produced, which quickly
filled my room with a white fog. That lasted for quite a while, and surprisingly it wasn't particularly harmful. After a while, no more SO3
formed, and I was left with a clear molten salt... which is Na2S2O5? or possibly something different, with concommitant O2 evolution.
Realising then that this must be SO3, I fed this with some plastic tubing into H2O, but to my dismay it did not seemingly dissolve, and lowered the pH
only a little. Nothing as impressive as bubbling Cl2 through NaOH.
Unfortunately, I never bubbled the SO3 through H2SO4 conc. - I wish I had done it, because it seems exceedingly easy to do, plus Na2S2O8 is serioulsy
easy to get! Maybe someone else try it for me? 
Never Stop to Begin, and Never Begin to Stop...
Tolerance is good. But not with the intolerant! (Wilhelm Busch)
|
|
|
Theoretic
National Hazard
Posts: 776
Registered: 17-6-2003
Location: London, the Land of Sun, Summer and Snow
Member Is Offline
Mood: eating the souls of dust mites
|
|
You probably got Na2SO4, Na2SO5 isn't stable at high temperatures.
I think you probably produced SO2 with a little bit of SO3 to create a fog and O2. The SO3 present dissolved and lowered the pH.
Anyway, that's my theory.
|
|
|
chemoleo
Biochemicus Energeticus
Posts: 3005
Registered: 23-7-2003
Location: England Germany
Member Is Offline
Mood: crystalline
|
|
No way. Ever smelled SO2? You can detect it quite easily. And there was definitely no SO2 smell around (unless repeated ethanolic
exposure screwed around my memories from more than a decade ago ).
Just try it out, this is an experiment that can be literally done in 10 minutes.
Never Stop to Begin, and Never Begin to Stop...
Tolerance is good. But not with the intolerant! (Wilhelm Busch)
|
|
|
axehandle
Free Radical
Posts: 1065
Registered: 30-12-2003
Location: Sweden
Member Is Offline
Mood: horny
|
|
My comments: When I tried superheating FeSO4 in an iron pipe I left it unattended, so it overheated and got yellow-hot. The entire flat was filled
with a thin white fog, but it had almost no smell -- it was just irritating to the lungs (smelt _slightly_ like SO2, but only a little, almost
undetectable). I think it was a mix of SO2 and SO3, mostly SO3.
I think chemoleo is right.
My PGP key, Fingerprint 5D96 E09E 365D 1867 2DF5 C2FE 4269 9C19 E079 CD35
\"Verbing nouns weirds the language!\"
|
|
|
jimwig
Hazard to Others
Posts: 215
Registered: 17-5-2003
Location: the sunny south
Member Is Offline
Mood: No Mood
|
|
it is my understanding that SO3 in air readily forms H2SO4 especially when inhaled and is quite irritating and painful to your lungs.
if you had any SO3 at all you should have been coughing and in pain.
|
|
|
axehandle
Free Radical
Posts: 1065
Registered: 30-12-2003
Location: Sweden
Member Is Offline
Mood: horny
|
|
NaHSO4 to Na2S2O7 by heat
I'm right now keeping 1/2 kg of NaHSO4 in my electrical furnace at 400 degrees C in an attempt to convert it to Na2S2O7. I'll tell you how
it goes...
On a more bizarre note, I'm going to take up pottery in about 10 minutes... going to make a couple of clay retorts. I'll post pictures,
regardless of the result...
[Edited on 2004-8-3 by axehandle]
My PGP key, Fingerprint 5D96 E09E 365D 1867 2DF5 C2FE 4269 9C19 E079 CD35
\"Verbing nouns weirds the language!\"
|
|
|
| Pages:
1
2
3
..
8 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
