dactyl
Unregistered
Posts: N/A
Registered: N/A
Member Is Offline
|
|
strange dioxane turbdity
Hello
I made dioxane by the dehydration of ethylene glycol and sulfuric acid. This dioxane was distilled in separate portions (due to the use of a smaller
distillation apparatus).
The combined crude dioxane was swirled in sodium hydroxide for 12 hours. Then the dioxane was decanted and distilled in separate portions with all of
the portions combined.
At this point I noticed that the dioxane was cloudy and I decided to redistill it. During observation I noticed that at first the distillate appeared
clear but then as the distillation progressed, the turbidity returned.
I took a sample of the dioxane and allowed it to evaportate and I noticed no residue.
Thus,
Is this dioxane too impure for solvent use?
Is there any way to remove the cloudiness?
What is the cloudy substance (if it is one)?
|
|
Tsjerk
International Hazard
Posts: 3028
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
How miscible are water and dioxane?
|
|
dactyl
Unregistered
Posts: N/A
Registered: N/A
Member Is Offline
|
|
If I remember very miscible
|
|
UC235
National Hazard
Posts: 565
Registered: 28-12-2014
Member Is Offline
Mood: No Mood
|
|
Dump more NaOH pellets in it. I find at least two hefty portions are needed to dry it and it should be allowed to stand over the solid for some time
to remove free acetaldehyde.
Dioxane is a pain in the ass, because manufacture from ethylene glycol produces a decent amount of 2-methyl-1,3-dioxolane (acetaldehyde ethylene
glycol acetal) as well as free acetaldehyde. The dioxolane is totally resistant to treatment with base but isn't stable to acid. It's boiling point is
too close to dioxane to effectively fractionate out, so purification requires alternating base and acid treatment
|
|
dactyl
Unregistered
Posts: N/A
Registered: N/A
Member Is Offline
|
|
After this would redistillation be necessary?
|
|
Tsjerk
International Hazard
Posts: 3028
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
I guess both NaOH and most acids will dissolve pretty well, so I think distillation will be necessary
|
|
dactyl
Unregistered
Posts: N/A
Registered: N/A
Member Is Offline
|
|
Update
The dioxane was subjected to a heaping amount of NaOH and was stirred for several hours and was left as is for several days.
Then, the dioxane was decanted and cold sulfuric acid was slowly added which resulted in a vigorous reaction. Thereafter, a separatory funnel of the
cold sulfuric acid was set up and the acid was allowed to drip at a rate of 1 drop per 3-5 minutes. The next morning the sulfuric acid/dioxane mixture
was allowed to stay together in a closed container for a few days. This mixture froze on the second day, I think, and was allowed to warm up.
Afterward, more sulfuric acid was added and this mixture was allowed to stand and was put back in the cold garage. Days later the H2SO4/ dioxane was
placed in a 1L round bottom flask and set for distillation. The temp did not exceed 120 C. The received distillate was turbid and white, much so than
before and the 1L flask had much black residue. Later the dioxane was distilled in a retort at a low temperature likely lower than the boiling point
of dioxane. After 3 1/2 hours the dioxane distillation was complete and was less turbid. The retort had much less black residue. The dioxane was
allowed to stand for a few days and became less turbid but with floating particles which I believe came from the jar.
Essentially after distillation from NaOH and H2SO4 treatment and a second distillation the mixture remains turbid though much less so on the second
round.
Could it be due to using 100% ethylene glycol straight from the antifreeze?
|
|