Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: Wire gauze with asbestos - should this smoke when I heat it???
pantone159
National Hazard
****




Posts: 590
Registered: 27-6-2006
Location: Austin, TX, USA
Member Is Offline

Mood: desperate for shade

[*] posted on 12-11-2006 at 18:01
Wire gauze with asbestos - should this smoke when I heat it???


I have a couple of squares of wire gauze/mesh, these both have asbestos in the center of them. (At least, there is a circle of white stuff in the middle, I assume this is asbestos.)

I hope to use these for heating flasks when using a flame, namely a backpacking stove. My setup has the stove on the bottom, an iron ring above that (with the gauze sitting on top of the ring), and the flask clamped above that, not touching anything. The gauze is supposed to disperse the heat to be more gentle to the glassware.

My problem, is that when I turn on the stove, the gauze starts to smoke. This seems bad. If I just heat it for a while, will the smoke-producing stuff soon burn off? Or am I just supposed to put up with the smoke?
View user's profile Visit user's homepage View All Posts By User
Magpie
lab constructor
*****




Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline

Mood: Chemistry: the subtle science.

[*] posted on 12-11-2006 at 21:00


I have one of those and use it all the time just as you have described. It doesn't smoke. I bought it new a year or so ago. I don't think it contains any asbestos as there has been so much hysteria over asbestos for so long now.

If your gauzes are very old they might well contain asbestos. I would think they would be fibrous if they contain asbestos.

I remember using a slurry of asbestos to form a filter mat in Gooch crucibles for analytical chemistry in the mid 60's. I also remember seeing old asbestos heating gauzes in school labs in the mid 80's.

[Edited on 13-11-2006 by Magpie]

[Edited on 13-11-2006 by Magpie]




The single most important condition for a successful synthesis is good mixing - Nicodem
View user's profile View All Posts By User
Jdurg
Hazard to Others
***




Posts: 220
Registered: 10-6-2006
Location: Connecticut, USA
Member Is Offline

Mood: No Mood

[*] posted on 13-11-2006 at 09:43


Asbestos is still routinely used in labs and in certain lab equipment. As much as they have tried, there is still no better fire and chemical resistant compound out there than asbestos. It is only a problem when it becomes airbone and can be inhaled. When confined in a matrix of other compounds, it is 100% non-toxic. Although the airborne fibers are nasty carcinogens, the "contained" fibers are the best fire/chemical-resistant compound known to man.



\"A real fart is beefy, has a density greater than or equal to the air surrounding it, consists of the unmistakable scent of broccoli, and usually requires wiping afterwards.\"
http://maddox.xmission.com.
View user's profile Visit user's homepage View All Posts By User
unionised
International Hazard
*****




Posts: 5126
Registered: 1-11-2003
Location: UK
Member Is Offline

Mood: No Mood

[*] posted on 13-11-2006 at 11:39


I could witter on about the availability and toxicity of asbestos or I could read your question
"If I just heat it for a while, will the smoke-producing stuff soon burn off?"
and answer it
Yes
View user's profile View All Posts By User
pantone159
National Hazard
****




Posts: 590
Registered: 27-6-2006
Location: Austin, TX, USA
Member Is Offline

Mood: desperate for shade

[*] posted on 13-11-2006 at 16:37


Upon further review the culprit is actually the iron ring. It has some sort of coating which is not surviving burner heat. (And then smokes and stinks.) I think I can do without it, though: since I am using a backpacking stove, I can just set the gauze right on top of it, and skip the ring.
View user's profile Visit user's homepage View All Posts By User

  Go To Top