Grantr
Hazard to Self
Posts: 57
Registered: 19-9-2015
Member Is Offline
Mood: No Mood
|
|
Detonator / booster size vs main charge
How do you determine how strong of a detonator/ booster you need for a given sized main charge? Is this more or less found by trial and error?
If a 1 gram ETN detonator sets off a 1/4 pound charge of say TNT, should I expect a 1 gram ETN detonator to set off a 5 pound charge of TNT?
No I do not have TNT this is just in theory and since TNT is somewhat hard to set off. I am trying to understand the dynamic behind how it works.
[Edited on 30-11-2015 by Grantr]
|
|
|
szuko03
Hazard to Others
Posts: 188
Registered: 3-4-2015
Location: USA
Member Is Offline
Mood: No Mood
|
|
I am pretty sure that as long as the force is high enough to start the "shock wave" through the compound that wave will propagate through the entire
mass regardless of the size as it is continued by the substance itself. I am not exactly sure but that's how i always viewed it.
The only issue may be if the substance itself blows apart by the shock wave and fragments before it can be propagated though.
Chemistry is a natural drive, not an interest.
|
|
|
careysub
International Hazard
Posts: 1339
Registered: 4-8-2014
Location: Coastal Sage Scrub Biome
Member Is Offline
Mood: Lowest quantum state
|
|
Quote: Originally posted by Grantr  | How do you determine how strong of a detonator/ booster you need for a given sized main charge? Is this more or less found by trial and error?
If a 1 gram ETN detonator sets off a 1/4 pound charge of say TNT, should I expect a 1 gram ETN detonator to set off a 5 pound charge of TNT?
No I do not have TNT this is just in theory and since TNT is somewhat hard to set off. I am trying to understand the dynamic behind how it works.
[Edited on 30-11-2015 by Grantr] |
If a 1 gram ETN detonator can set off a 1/4 pound charge it can set off a one million pound charge. Once the detonation wave is established in a
self-sustaining way in the main charge it will propagate forever.
|
|
|
OneEyedPyro
Hazard to Others
Posts: 280
Registered: 7-10-2015
Member Is Offline
Mood: No Mood
|
|
Many HEs can go low order without adequate initiation, with smaller charges ANFO can go high order from a weak initiatior but with a large charge
you'll get a partial/low order det.
It really all depends on the explosive in question, some will accelerate to full detonation velocity with insufficient initiation while others will
undergo a partial det.
[Edited on 1-12-2015 by OneEyedPyro]
|
|
|
Grantr
Hazard to Self
Posts: 57
Registered: 19-9-2015
Member Is Offline
Mood: No Mood
|
|
Thanks guys.
Interesting you say any HEs can go low order without adequate initiation. I knew that Nitroglycerin would do that.
I have noticed Ammonal mixed at a 97% AN to 3% AL ratio has a much louder detotation and stronger shockwave when set off with .5 grams of ETN vs being
shot with a rifle. Also a rifle will not set it off with a 90/10 ratio while ETN will and being mixed at that ratio is quite a bit stronger with more
aluminum.
Why does ANFO behave differently in larger quantities? I did try a 40 gram ANFO charge in a ziplock bag. .5 grams ETN only partially set it off.
Nothing remotly close to 40 gram ammonal.
|
|
|
careysub
International Hazard
Posts: 1339
Registered: 4-8-2014
Location: Coastal Sage Scrub Biome
Member Is Offline
Mood: Lowest quantum state
|
|
For nearly all explosives capable of undergoing detonation ("high explosives") there is a critical size of the explosive mass required to create a
self-sustaining detonation wave.
This is usually measured by the critical diameter of an unconfined column of explosive that will maintain a constant velocity detonation wave. If the
diameter is less than the critical size even establishing a detonation with a strong initiation will not create a self-sustaining wave , it will slow
down, weaken, and die out. The energy lost from the sides of the column is too great.
ANFO has a very large critical diameter, so small quantities will not sustain a detonation well. Large driving charges relative to the main explosive
are required to achieve nearly complete detonation. Not a problem in the blasting applications in which it is employed, though the loading bore holes
do need to have adequate diameter.
Confinement of course helps.
Some explosives can detonate in extremely small quantities. The well known primary explosives are examples of these, which is largely what makes them
useful in that role.
A technical discussion is found here:
http://www.dtic.mil/dtic/tr/fulltext/u2/a106485.pdf
[Edited on 1-12-2015 by careysub]
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
