Schleimsäure
Hazard to Others
Posts: 156
Registered: 31-8-2014
Location: good ole Germany
Member Is Offline
Mood: Probably
|
|
Concentration of HNO3 with H2SO4
Hallo,
so I wanted to make 99+% HNO3 by concentrating the 65% solution with conc. H2SO4.
I read that using a vacuum destillation prevents the production of NOx thus just resulting in a clear product.
So I mixed the acids in a ratio of 5:4 HNO3/H2SO4.
The joints of the destillation setup all have been greased well.
The already hot acid mixture immediately started to boil after vaccum was put on. The heating mantle I put on just thereafter, but it needs some
minutes to heat anyway.
The HNO3 came over just seconds after vaccum was laid on. Destillation in the 400mm Liebig was very fast - and clear. No NO2 at all.
But after 1 or 2 min or so a cloud of NO2 formed in a heartbeat and went through the Liebig into the receiver flask and finally contaminated the clear
HNO3 deyeing it reddish.
I immediately interrupted the vaccum to stop the destillation. Fortunately I put a washing bottle between vaccum adapter and oil pump, which had
actually collected some NO2.
So my question is what went wrong? I have no manomter yet, so I don't know the strength of the vacuum. I read that the particuar pump I use creates a
good vacuum of 0,05 mbar, although it is a relatively cheap one with no extras like manometer.
Maybe the vacuum setup had a leak? I forgot to grease the joint of the securing washing bottle. 
[Edited on 4-7-2015 by Schleimsäure]
|
|
|
aga
Forum Drunkard
Posts: 7030
Registered: 25-3-2014
Member Is Offline
|
|
Vacuum should have taken care of major leaks in a ground-glass rig.
Hazarding a guess, the mix got heated too much for that reduced pressure, decomposing the HNO3.
Hopefully an illumni will come along and illumni-ate.
Edit :
A quick wiki and i found
https://en.wikipedia.org/wiki/Nitric_acid
If it does decompose to NO2 and water, the conc Sulphuric acid should sequestrate the water, giving you the brown gas rather than the
nitric acid.
Interesting.
Possibly not the best way to get RFNA, yet interesting.
[Edited on 5-7-2015 by aga]
|
|
|
Schleimsäure
Hazard to Others
Posts: 156
Registered: 31-8-2014
Location: good ole Germany
Member Is Offline
Mood: Probably
|
|
Actually on versuchschemie a longtime reputable member uses this method with great success, meaning without any noticable NO2 formation. Thus he
actually gets WFNA.
He measured density of his clear acid and got 1,51g/cm3, which is not too bad. He used 53% HNO3 and found a ratio of 5:4 or 4:3 HNO3(53%):H2SO4 (96%)
is the best after some runs.
To further concentrate it you have to repeat the whole procedure with the 1,51g/cm3 acid product of your first run.
Also he made a test and nitrated a gram of Hexamine with success.
On my attempt the first 30-50 ml actually came over clear as it should be for up to 2 min.
Maybe the vacuum was too strong. I don't know.
[Edited on 5-7-2015 by Schleimsäure]
|
|
|
hissingnoise
International Hazard
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
| Quote: | | But after 1 or 2 min or so a cloud of NO2 formed in a heartbeat and went through the Liebig into the receiver flask and finally contaminated the clear
HNO3 deyeing it reddish. |
Did you use stopcock grease to seal your joints?
|
|
|
Fulmen
International Hazard
Posts: 1718
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
Since it boiled around room temp with the reduced pressures a heating mantle could cause unnecessary high temps. A water bath should give more control
over the process and reduce the risk of overheating. When I researched this (pre-web) I ended up with a 50/50 mix (by volume) of 67% HNO3 and 98%
H2SO4, this seems to be the standard in industrial setups. Yield was appr 1/2 the initial volume of the HNO3.
We're not banging rocks together here. We know how to put a man back together.
|
|
|
Schleimsäure
Hazard to Others
Posts: 156
Registered: 31-8-2014
Location: good ole Germany
Member Is Offline
Mood: Probably
|
|
Quote: Originally posted by hissingnoise  | | Quote: | | But after 1 or 2 min or so a cloud of NO2 formed in a heartbeat and went through the Liebig into the receiver flask and finally contaminated the clear
HNO3 deyeing it reddish. |
Did you use stopcock grease to seal your joints?
|
I used Silicone grease from LIQUIMOLY. It's recommended on versuchschemie and had no problems with it so far.
http://www.amazon.de/Liqui-Moly-3312-Silicon-Fett-transparen...
|
|
|
Schleimsäure
Hazard to Others
Posts: 156
Registered: 31-8-2014
Location: good ole Germany
Member Is Offline
Mood: Probably
|
|
| Quote: Originally posted by Fulmen | | Since it boiled around room temp with the reduced pressures a heating mantle could cause unnecessary high temps. A water bath should give more control
over the process and reduce the risk of overheating. When I researched this (pre-web) I ended up with a 50/50 mix (by volume) of 67% HNO3 and 98%
H2SO4, this seems to be the standard in industrial setups. Yield was appr 1/2 the initial volume of the HNO3. |
Yes, but the thing is the NO2 formed already when the heating mantle wasn't even warm yet after 2 min.
One issue could be that we have the warmest days in decades here in Germany. Room temp is arround 30 degrees C.
The nitrating acid in the reaction flask already had a temperature of up to 100 degrees C on its own. This plus high vacuum plus high room temperature
could have led to decomposition of some HNO3. For two minutes temperature was ok and must have risen without external heat to an undesirable point.
I just wonder, because the guy on versuchschemie used vacuum plus heating mantle without decomposition. Unfortunately he didn't say what kind of
vacuum source, hence strength, he used. It's from a very old thread from 2005 or so. Maybe he used just water-jet vacuum back then...
[Edited on 5-7-2015 by Schleimsäure]
|
|
|
papaya
National Hazard
Posts: 615
Registered: 4-4-2013
Member Is Offline
Mood: reactive
|
|
Couldn't you use conc. sulfuric acid instead of grease ?
|
|
|
Schleimsäure
Hazard to Others
Posts: 156
Registered: 31-8-2014
Location: good ole Germany
Member Is Offline
Mood: Probably
|
|
Yes, that's a possibility. But in the end I don't really know if this is the problem at all.
Here's a picture.
Don't know whether to go on from here or use a new setup.
|
|
|
Fulmen
International Hazard
Posts: 1718
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
That could be the problem. The point of vacuum distillation is to keep the temperature down, so why start with hot liquids?
We're not banging rocks together here. We know how to put a man back together.
|
|
|
macckone
Dispenser of practical lab wisdom
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
Likely culprit for vacuum loss, the thermometer seal.
Unless you replaced it with a viton O-ring,
it will get eaten up in nothing flat.
Recommendation, get teflon seals for your joints.
These are available at United Glass Tech.
Next get a thermometer well from
Roccoware Glass Works.
This will leave everything as teflon or glass in contact
with your nitric acid.
Another recommendation is to replace what appears
to be a rubber hose with a pvc hose.
Exploding hoses are no fun. And I mean nitrated
and then exploding not just rupturing.
It looks like your second hose coming off of the trap
is already pvc. But it is hard to tell from the picture.
Good luck with your experiments.
|
|
|
Schleimsäure
Hazard to Others
Posts: 156
Registered: 31-8-2014
Location: good ole Germany
Member Is Offline
Mood: Probably
|
|
| Quote: Originally posted by Fulmen |
That could be the problem. The point of vacuum distillation is to keep the temperature down, so why start with hot liquids? |
Good point. Next time I'll try to use a chilled down acid mixture.
[Edited on 5-7-2015 by Schleimsäure]
|
|
|
Schleimsäure
Hazard to Others
Posts: 156
Registered: 31-8-2014
Location: good ole Germany
Member Is Offline
Mood: Probably
|
|
| Quote: Originally posted by macckone | Likely culprit for vacuum loss, the thermometer seal.
Unless you replaced it with a viton O-ring,
it will get eaten up in nothing flat.
Recommendation, get teflon seals for your joints.
These are available at United Glass Tech.
Next get a thermometer well from
Roccoware Glass Works.
This will leave everything as teflon or glass in contact
with your nitric acid.
Another recommendation is to replace what appears
to be a rubber hose with a pvc hose.
Exploding hoses are no fun. And I mean nitrated
and then exploding not just rupturing.
It looks like your second hose coming off of the trap
is already pvc. But it is hard to tell from the picture.
Good luck with your experiments. |
Also a good hint. thank you. I don't exactly need the thermometer, so I could just put in a NS14 stop cock. On the other hand the thermometer has a
NS14 boro glass joint, no adapter. It's all high quality labware. Contacts are actually only glass besides the hoses.
Yes the second hose is PVC. Maybe I find a proper second PVC one for the vacuum adapter.
If vacuum loss has taken place I still suspect the ungreased washing bottle joint.
[Edited on 5-7-2015 by Schleimsäure]
|
|
|
Bot0nist
International Hazard
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
The following ma be veering slightly off of the OP, since I cant offer much advice for or improvements on existing procedures for distilling
concentrated WFNA from strong sulfuric acid and some common alkali nitrate salts. Conc. acid, dry sodium nitrate, careful control of pot temperature,
and reduced pressure with the proper ground glass joints, sealed.with a smear of sulfuric acid or inert vacuum grease are all good tips that have
been dished out here over the years. The initial volume of raw nitric acid obtained can then be further concentrated and purified to an extent if
mixed with more conc. sulfuric acid and distilled again, with a careful eye kept of the distillate temp coming over.
I Hope though that it may be of use to anyone making concentrated nitric acid, but that may be lacking a vacuum source, or other accessories needed to
produce concentrated, nearly clear HNO<sub>3</sub> with minimal nitrogen oxide contaminates IIRC, in the past several members, myself
included, have had some success in clearing up smaller volumes of freshly made RFNA (red fuming nitric acid), with dissolved and fuming nitrogen
oxides) by slowly bubbling dry air, CO<sub>2 </sub> or even dry ozone supplemented air, with the use of an aquarium pump or regulated
cylinder. Employ a clay bubble stone to aid in proper gas diffusion to speed the reaction up, and, of course, lead the gas through inert to strong,
oxidizing nitric acid, and through a drying tube and then allow.it to bubble through the concentrated, red fuming isolate for some time until.it
clears.
Doing this will slowly clarify the isolate to a decent quality of WFNA (white fuming nitric acid) which will work just a good for most applications,
and yet is suitable for use in procedures where the RFNA won't do, and clean WFNA is called for.
I think our very own <b>hissingnoise</b> had been, at least in the past in the past a proponent of this slightly time consuming, yet
practical, cheap and simple solution to cleaning up home made RFNA into quality WFNA.
Good lick, and stay safe.
[Edited on 6-7-2015 by Bot0nist]
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Low pressure favours formation of gases (to 'restore' pressure again), so also the decomposition of nitric acid. Too high temperature is almost
certainly to blame here, as an aggravating factor.
The whole method seems like a sad waste of conc. H2SO4, though.
Why not displace an ionic nitrate with conc. H2SO4? That should yield above the azeotropic composition.
[Edited on 6-7-2015 by blogfast25]
|
|
|
hissingnoise
International Hazard
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
| Quote: | | I think our very own hissingnoise had been, at least in the past in the past a proponent of this slightly time consuming, yet practical, cheap and
simple solution to cleaning up home made RFNA into quality WFNA. |
Indeed yes Bot0nist, though I'd be somewhat loath to leave a stirrer and compressor on overnight again.
Using the output of an airfed ozoniser will be quicker and more complete and can, in theory, increase acid density as nox products in the effluent are
partly oxidised by ozone to form the anhydride, N2O5!
|
|
|
aga
Forum Drunkard
Posts: 7030
Registered: 25-3-2014
Member Is Offline
|
|
In terms of applying the word 'concentrated' what w% would qualify for HNO3 ?
|
|
|
Metacelsus
International Hazard
Posts: 2539
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
In my opinion, azeotropic and above.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
