evil_lurker
National Hazard
Posts: 767
Registered: 12-3-2005
Location: United States of Elbonia
Member Is Offline
Mood: On the wagon again.
|
|
What vacuum funnel porosity to get?
May sound like a simple question... but I don't have any first hand experience so some advice would be greatly appreciated...
Course, medium, or fine porosity?
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
I like the ceramic Buchner funnel with the fixed holed plate. You then place a filter paper of your choice over this. This way your porosity options
are unlimited.
Is this what you are asking?
I don't think I would buy a fritted glass funnel unless that was the only option - too hard to maintain.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
evil_lurker
National Hazard
Posts: 767
Registered: 12-3-2005
Location: United States of Elbonia
Member Is Offline
Mood: On the wagon again.
|
|
No not really. Honestly I was thinking that the vacuum might suck the material through the paper if the holes were too big or that it might interfere
with the rate of filtration.
I agree on staying away from the fritted glass funnels. I was however thinking of snagging a new medium porosity 24/40 350ml glass buchner funnel with
vacuum take off for $40... similar models list for well over $100.
I already snagged a brand spanking new 20ml 24/40 dean-stark trap with teflon stopcock and overflow for $36 this morning... I'm on a roll.
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
I just received a 15cm (6") Coors Buchner funnel won on eBay for $20. This would cost 4 to 5 times that amount from a science supply house. Praise
be to eBay! 
I can usually get by fine with my 7cm Buchner for the regular small scale organic systhesis, etc. But when you run into a tough to filter material
where you need to spread out a lot of diatomaceous earth the larger filter will be much better. It has 4 times the area (and capacity) of the smaller
one.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
Fleaker
International Hazard
Posts: 1252
Registered: 19-6-2005
Member Is Offline
Mood: nucleophilic
|
|
I bought a 6" from ebay for about $32 then when I opened up the package the seller had sent me a 4" too! Apparently she wanted to get rid of it b/c of
the small crack on the lip and the fact it took a week for her to send it to me!
Just use a strong filter paper for Buchner/vacuum filtration and you shouldn't have too much worry about ripping it. Again, choose the right paper for
the job, just calling the people at Whatman can be very beneficial.
Fritted glass funnels are nice, but expensive. Cleaning them isn't exactly fun, although they're great for getting every last bit of precipitate
providing you have a lot of time to spend watching it filter.
|
|
|
bio2
Hazard to Others
Posts: 447
Registered: 15-1-2005
Member Is Offline
Mood: No Mood
|
|
My 90mm pyrex buchner w a medium frit almost always gets paper anyway and the regular perforated glass plate one gets used much more.
Those frits are a major pain in the ass to clean and learned my lesson by filtering
some Fe sludge, I think it was, when it was real new. Man, that was a mistake, took days to get the shit out and have used paper on it every since.
If you get one of these keep the gunky stuff far away from them or you will regret it.
|
|
|
Ephoton
Hazard to Others
Posts: 463
Registered: 21-7-2005
Member Is Offline
Mood: trying to figure out why I need a dark room retreat when I live in a forest of wattle.
|
|
yep ill second that I once had a lovley funnel damb al sludge
|
|
|
mick
Hazard to Others
Posts: 338
Registered: 3-10-2003
Member Is Offline
Mood: No Mood
|
|
I have used stuff called Decon 90 and other stuff called Lipsol in the UK to clean sintered glass funnels. After soaking neat for 2 or 3 days and
pushing water up through the sinter they have cleaned the funnel better than conc nitric.
mick
|
|
|
neutrino
International Hazard
Posts: 1583
Registered: 20-8-2004
Location: USA
Member Is Offline
Mood: oscillating
|
|
I've got a question about cleaning glass frits. Is simply soaking the frit in <b>dilute</b> nitric acid of any use? That's what my
chemistry teacher said to do, but I personally don't see how this would help, especially because the acid doesn't seem to reach the interior of the
frit.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
