guy
National Hazard
Posts: 982
Registered: 14-4-2004
Location: California, USA
Member Is Offline
Mood: Catalytic!
|
|
H2O2 + Cu(OH)2
What is the reaction when copper(II) hydroxide is mixed with hydrogen peroxide? The product seems to be CuO (black) and some gas (O2 or H2). It only
works when H2O2 is added to a basic precipitate of copper(example CuCO3). I can't figure it out because it doesn't do this to other
hydroxides that I have tried, Fe(OH)3.
|
|
|
The_Davster
A pnictogen
Posts: 2861
Registered: 18-11-2003
Member Is Offline
Mood: .
|
|
It does that to other hydroxides as well, I have made Fe2O3 by reacting Fe(OH)2 with peroxide, creating a suspension of Fe2O3 which can be
precipitated by adding NaOH.
|
|
|
woelen
Super Administrator
Posts: 8012
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
This certainly is not a beginners question. H2O2 forms very peculiar compounds with a whole bunch of metal hydroxides, carbonates and many other
precipitates.
I personally think that the peculiar reactions are a combination of redox reactions and complex formation (coordination reactions).
Similar effects occurs with titanium, vanadium, iron, cobalt, cerium (IV) and possibly others. The problem is that most of these are not simple redox
reactions where the metal is oxidized to higher oxidation state.
E.g. ferrous ion under neutral conditions seems to form very special iron (IV) species (google "Fenton's reagent" for more info).
Copper seems to form peroxo-complexes of varying color. The reaction of cerium (IV) with hydroxide and hydrogen peroxide is a total mystery to me.
|
|
|
BromicAcid
International Hazard
Posts: 3245
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Thanks Woelen for bringing up Fenton's Reagent, there is a variation on it that actually uses copper salts in place of iron salts (Searching
'Fenton's Reagent Copper' gives some relevent results), although I thought most of the oxidizing ability of Fenton's Reagent took
place under slightly acidic conditions, could it just be that the intermediate oxidizing agents are just more stable under basic conditions so less
oxidizing?
|
|
|
woelen
Super Administrator
Posts: 8012
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Yes, you are right. The conditions must be slightly acidic. I have tested it by dissolving Mohr's salt (ferrous ammonium sulfate) in water and
adding H2O2. A solution of Mohr's salt is slightly acidic on its own.
The copper variation of Fenton's reagent indeed is very special. It is a combination of copper (II) ions, chloride ions and ascorbate, which
allows hydrogen peroxide or even oxygen from the air to form hydroxyl radicals in solution. I know of its special oxidizing properties, but I do not
understand precisely how it works (why does it form hydroxyl radicals, what is the role of the chloride ions?).
|
|
|
I am a fish
undersea enforcer
Posts: 600
Registered: 16-1-2003
Location: Bath, United Kingdom
Member Is Offline
Mood: Ichthyoidal
|
|
How hot did the reaction mixture get? Copper(II) hydroxide readily decomposes to the oxide in warm water. It is possible that the
Cu(OH)<sub>2</sub> merely catalysed the decomposition of the hydrogen peroxide into water and oxygen, and then the resulting rise in
temperature (H<sub>2</sub>O<sub>2</sub> decomposition is very exothermic) caused the Cu(OH)<sub>2</sub> to
decompose.
1f `/0u (4|\\| |234d 7|-|15, `/0u |234||`/ |\\|33d 70 937 0u7 /\\/\\0|23.
|
|
|
guy
National Hazard
Posts: 982
Registered: 14-4-2004
Location: California, USA
Member Is Offline
Mood: Catalytic!
|
|
I only used 3% H2O2. The reaction was exothermic and was warm. Not like super warm, but it got warmer. I don't think its warm enough to
decompose because I have heated Cu(OH)2 to higher temps without decomposition.
[Edited on 11/28/2005 by guy]
|
|
|
woelen
Super Administrator
Posts: 8012
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
| Quote: | Originally posted by I am a fish
How hot did the reaction mixture get? Copper(II) hydroxide readily decomposes to the oxide in warm water. It is possible that the
Cu(OH)<sub>2</sub> merely catalysed the decomposition of the hydrogen peroxide into water and oxygen, and then the resulting rise in
temperature (H<sub>2</sub>O<sub>2</sub> decomposition is very exothermic) caused the Cu(OH)<sub>2</sub> to
decompose. |
I don't think it is heating. I have done this similar experiment with cold 1% H2O2 and then still the precipitate turns dark.
A similar effect is observed, when a solution of Na2S2O8 is added to a precipitate of Cu(OH)2. Apparently the oxidizing capabilities have something to
do with this.
|
|
|
guy
National Hazard
Posts: 982
Registered: 14-4-2004
Location: California, USA
Member Is Offline
Mood: Catalytic!
|
|
Maybe this reaction is similar to the reaction of calcium hydroxide added to H2O2. That reaction forms calcium peroxide. So maybe this reaction
forms copper (ii) peroxide which ultimatly decomposes to copper (ii) oxide. But somehow the reaction only takes place in a basic solution. Perhaps
it is because H2O2 is a very weak acid, which causes it to react and form a peroxide (due to insolubility).
| Quote: |
A similar effect is observed, when a solution of Na2S2O8
|
Peroxysulfate hydrolyses to hydrogen peroxide, so that explains the similar effect.
Cu(OH)2(s) + H2O2(aq) ---> CuO2(s) + 2H2O(s)
then
2CuO2(s) ---> 2CuO(s) + O2(g)
Anyways, that's my guess. It seems to make sense.
[Edited on 11/29/2005 by guy]
[Edited on 11/29/2005 by guy]
[Edited on 11/29/2005 by guy]
[Edited on 11/29/2005 by guy]
|
|
|
12AX7
Post Harlot
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
CuO2 as a transient state, or do you mean the (unbalanced equation using) CuO2(2-) cuprate ion? This does exist, in strongly basic conditions.
Tim
|
|
|
guy
National Hazard
Posts: 982
Registered: 14-4-2004
Location: California, USA
Member Is Offline
Mood: Catalytic!
|
|
I meant copper(ii) peroxide. I'm guessing that the formula is CuO2.
|
|
|
woelen
Super Administrator
Posts: 8012
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
| Quote: | Originally posted by guy | Quote: |
A similar effect is observed, when a solution of Na2S2O8
|
Peroxysulfate hydrolyses to hydrogen peroxide, so that explains the similar effect.
|
Are you sure? How can you explain the following observations, assuming your theory is right?
1) Persulfate added to a light green precipitate of Ni(OH)2 forms a black solid, at once.
2) Hydrogen peroxide added to Ni(OH)2 does not give any (visible) reaction.
3) Hydrogen peroxide, added to the black result of Na2S2O8/Ni(OH)2 causes the black stuff to change to light green Ni(OH)2 again.
If persulfate would form hydrogen peroxide, then observations (2) and (3) could not be explained at all.
|
|
|
stygian
Hazard to Others
Posts: 242
Registered: 19-9-2004
Member Is Offline
Mood: No Mood
|
|
'persulfate' is a broad term. I don't think theyre like percarbonates, which have H2O2 of hydration, these actually have peroxide
bonds on the sulfur.
|
|
|
guy
National Hazard
Posts: 982
Registered: 14-4-2004
Location: California, USA
Member Is Offline
Mood: Catalytic!
|
|
Well, I thought you meant peroxydisulfate ((SO4)2)2- or S2O8 2-. And the peroydisulfate hydrolysizes to H2O2 (it is how H2O2 is produced in the
electrolysis of ammonium bisulfate).
S2O8<sup>2-</sup> + 2H2O -----> H2O2 + 2HSO4<sup>-</sup>
H2O2 only shows its strongest oxidizing abilities in an acidic sloution. Alkaline solutions are needed to form NiOOH(Ni(III)). So I think thats why
persulfate works, since it is an oxidizer in alkaline slns.
[Edited on 11/30/2005 by guy]
[Edited on 11/30/2005 by guy]
[Edited on 11/30/2005 by guy]
[Edited on 11/30/2005 by guy]
[Edited on 12/2/2005 by guy]
|
|
|
woelen
Super Administrator
Posts: 8012
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Yes I am talking about S2O8(2-), the peroxidisulfate ion. But still, this does not answer my question.
Why is the black nickel (III) (or nickel (IV)) oxide/hydroxide precipitate turned light green by hydrogen peroxide in alkaline solution. In order to
be clear, I'll repeat the entire experiment:
1) Add a solution of NiSO4 to a solution of NaOH, such that there is quite some excess NaOH. This gives a light green precipitate of Ni(OH)2.
2) Add a solution of Na2S2O8. This immediately causes the light green precipitate to turn black. I think this is due to formation of either nickel
(III) or nickel (IV) oxide/hydroxide. I've seen both explanations.
3) Add some H2O2 to the still very alkaline solution with the black precipitate. Quickly the precipitate becomes light green again. The liquid still
is very alkaline.
A second experiment: Add some H2O2 to a green suspension of Ni(OH)2 in an alkaline solution of excess NaOH. No visible change at all can be observed.
When more H2O2 is added, it remains the same.
I have the feeling there is something contradictory in stating that S2O8(2-) gives H2O2 in solution and at the same time, adding H2O2 makes the
precipitate turn green again.
|
|
|
guy
National Hazard
Posts: 982
Registered: 14-4-2004
Location: California, USA
Member Is Offline
Mood: Catalytic!
|
|
It is because H2O2 is not a strong oxidizing agent in a basic solution, therefore it will not oxidize Ni(II) to Ni(III). H2O2 will exihibit its
strong oxidizing abilities in an acid solution.
2H+ + H2O2 --> 2H2O E = 1.77V
And as for turning green, it is because H2O2 is a weak acid and shifts the equilibrium left again.
Ni(OH)2 + 2OH– + S2O8(2-) → NiO2 + 2SO42- + 2H2O
Adding acid, reacts with the Ni(OH)2 and shifts it back. And furthermore the hydrolysis of S2O8(2-) is significantly slower than the reduction of
S2O8(2-) in this reaction.
Also, the changing of S+7 to S+6 is stronger than the oxidizing power of hydrogen peroxide. It is +2.42V.
So in this case, the peroxydisulfate is the main oxidizer. In the case otf Cu(OH)2, the H2O2 acid-base reaction is the main component.
[Edited on 12/1/2005 by guy]
[Edited on 12/1/2005 by guy]
|
|
|
woelen
Super Administrator
Posts: 8012
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
I'm very persistant on this, because I'm still not convinced  . This is
not to annoy you , but I simply want to have this issue settled, until I totally
understand it.
If I do the experiment with very concentrated NaOH with a little Ni(OH)2 in it, then adding Na2S2O8 makes the precipitate black. Adding a few drops of
H2O2 again makes the precipitate green. But after this, the liquid still is very alkaline. I used a LOT of NaOH, so the concentration hardly changed
with the small amounts of other reagents mixed in.
So, the argumentation of equilibrium shifting towards green Ni(OH)2 due to shift of pH does not hold.
I also did a counter experiment without adding H2O2, but dripping in HCl. When this is done, then the precipitate remains black, until a point is
reached, where the liquid really becomes acidic. At that point the precipitate very slowly dissolves and a smell of chlorine can be observed.
So, with H2O2 a few drops of 10% H2O2 are sufficient to make the black precipitate green again. With 10% HCl a lot of acid was needed before the black
precipitate disappears.
I also did another experiment by using a large excess amount of Na2S2O8, relative to the Ni(OH)2. The rationale behind that is that the Ni(OH)2 is
quickly converted to the black NiO2/NiO(OH). After this, a lot of Na2S2O8 remains. If this slowly forms H2O2, then the black color should fade again
and it should become light green again. Well, I've done this and left the test tube overnight, but it remained black.
Tonight I will do another test experiment. If Na2S2O8 indeed gives H2O2, due to hydrolysis, then an (acidic) solution of Na2S2O8 should turn an
acidified solution of K2Cr2O7 deep blue. This is a well-known qualitative test for dichromate or peroxide. I'll keep you updated on this.
Another remark: S in S2O8(2-) does not have oxidation state +7. It still is +6. Only the two oxygens between the two sulphurs in this ion have
oxidation state -1 instead of -2.
Are you sure that the redox potential is +2.42V under the conditions I have? I thought it is just over 2 V. But this is not essential for the question
about the Ni(OH)2 --> NiO2 conversion  .
|
|
|
guy
National Hazard
Posts: 982
Registered: 14-4-2004
Location: California, USA
Member Is Offline
Mood: Catalytic!
|
|
Okay
I have another (I hope better) explanation.
To make peroxydisulfuric acid:
H2O2 + 2H<sup>+</sup> + 2SO4<sup>2-</sup> <------> S2O8<sup>2-</sup> + 2H2O
If you add H2O2, the equilibrium is shifted back to S2O8<sup>2-</sup>. Adding and acid (HCl for example) will also shift the equilibrium
right, but more is needed because it takes 4x as much. I hope that this is a better explation. Also, try adding excess sulfate ions and see if this
causes a similar effect.
AND ALSO
going bak to the main topic , does anyone agree with my acid-base theory for the
reaction of Cu(OH)2 with H2O2?
[Edited on 12/2/2005 by guy]
[Edited on 12/2/2005 by guy]
[Edited on 12/2/2005 by guy]
[Edited on 12/2/2005 by guy]
|
|
|
neutrino
International Hazard
Posts: 1583
Registered: 20-8-2004
Location: USA
Member Is Offline
Mood: oscillating
|
|
That should make peroximonosulfufic (Caro's) acid:
H<sub>2</sub>O<sub>2</sub> + H<sub>2</sub>SO<sub>4</sub> -->
H<sub>2</sub>SO<sub>5</sub> + H<sub>2</sub>O
|
|
|
woelen
Super Administrator
Posts: 8012
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
| Quote: | Originally posted by guy
Okay
I have another (I hope better) explanation.
To make peroxydisulfuric acid:
H2O2 + 2H<sup>+</sup> + 2SO4<sup>2-</sup> <------> S2O8<sup>2-</sup> + 2H2O
If you add H2O2, the equilibrium is shifted back to S2O8<sup>2-</sup>. Adding and acid (HCl for example) will also shift the equilibrium
right, but more is needed because it takes 4x as much. I hope that this is a better explation. Also, try adding excess sulfate ions and see if this
causes a similar effect. |
I have done some more experimenting with persulfate and H2O2.
First the test with acidified dichromate. Addition of persulfate does not result in formation of the deep blue peroxo compound of chromium. Not even a
trace of this can be observed. A counter experiment with adding a single drop of 1% H2O2 immediately results in formation of deep blue CrO5. So, we
can safely conclude that persulfate does not hydrolyse to hydrogen peroxide in acidic media.
I did the same test in alkaline environment. Adding H2O2 to a yellow solution of K2CrO4 results in formation of a brown complex (CrO8(3-)). This
reaction also is quite sensitive. When persulfate is added to an alkaline solution of K2CrO4, then no change of color can be observed, nothing at all,
even when a lot of persulfate is added. So, we can also safely conclude that persulfate does not form hydrogen peroxide in alkaline environments.
Besides that, I also read about Caro's acid, as neutrino mentions. This indeed is the equilibrium reaction, not the persulfate. Persulfate is
formed electrolytically from sulfate:
SO4(2-) --> SO4(-) + e (at anode)
2SO4(-) --> (-)O3SOOSO3(-), which is persulfate
Finally, a remark on the 4 times strength of H2O2 relative to HCl. Even if this were the case, it cannot explain my observations. With H2O2 (10%) a
single drop suffices to remove the black compound, with HCl, several ml are needed. I think a factor of 50 is more close to what I observe than a
factor of 4.
| Quote: |
AND ALSO
going bak to the main topic, does anyone agree with my acid-base theory for the
reaction of Cu(OH)2 with H2O2? |
No, I think that the mechanism is different. I agree with that a peroxide may be formed, such as CuO2. I, however, think it is a coordination reaction
and not an acid-base reaction. The Cu(OH)2 is not real Cu(OH)2, it is a very complicated macro-structure with Cu-ions, OH(-) ligands and H2O ligands
forming a complex structure, with empirical formula Cu(OH)2.nH2O. As in Fenton's reagent, I believe that H2O2 ligands replace H2O or OH(-)
ligands, followed by subsequent loss of hydroxyl radicals. This can lead to formation of CuO2.nH2O.
|
|
|
guy
National Hazard
Posts: 982
Registered: 14-4-2004
Location: California, USA
Member Is Offline
Mood: Catalytic!
|
|
From
http://astronautix.com/props/h2o2.htm | Quote: |
Hydrogen peroxide is manufactured commercially by several processes. Inorganic processes employ the electrolysis of an aqueous solution of sulphuric
acid or acidic ammonium bisulphate, followed by hydrolysis of the peroxydisulfate which is formed.
|
There are also more sites which support this.
| Quote: |
That should make peroximonosulfufic (Caro's) acid:
|
I said
H2O2 + 2H+ + 2SO42- <------> S2O82- + 2H2O
This is reaction is definately valid for the formation of a peroxydisulfate.
And, for the test with persulfate in acidic solution will not form H2O2, because that will the reaction form more S2O8(2-). Alkalne enviroment will
cause H2O2 to decompose to O2 and H2O. Try in a neutral enviorment, and see if this causes any change.
Also, try adding excess sulfate ions to see if the NiO2 will redissolve.
*****************************
And on the Cu(OH)2 + H2O2 subject.
You believe the reaction is
Cu(H2O)3(OH)2 + H2O2 ---> Cu(H2O)3(H2O2)(OH)]<sup>-</sup> ---> ?CuO2 + .OH?
Can you explain more on the mechanism of this reaction?
And can you explain how this reaction is different from Ca(OH)2 + 2H2O2 --> CaO2 + 2H2O?
[Edited on 12/3/2005 by guy]
[Edited on 12/3/2005 by guy]
[Edited on 12/3/2005 by guy]
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
