| Pages:
1
2 |
CHRIS25
National Hazard
Posts: 951
Registered: 6-4-2012
Location: Ireland
Member Is Offline
Mood: No Mood
|
|
calcium carbonate composition in seashells
I have just finished a lengthy experiment with seashells and am surprised by the results.
Experiment:
Exactly 100g white seashells (see image) were dissolved in an eventual total 7 moles HCl, the resulting CaCl2 solution was then treated
with NaHCO3.
The expected outcome was approx 90g or less of Calcium Carbonate based on various topics that referred to seashells as being mostly Calcium carbonate
minus 2 - 5% in protein and other ingredients.
These are now my results:
375g CaCO3 fully dried and weighed in as such.
Working backwards then:
375g CaCO3 = 3.75mol
CaCl2 solution must have been 2.8mol
and the actual needed HCl stoichiometrically would have been 5.6mol, (Which is quite close to the 7mol added good enough knowing that I added a little
to much to allow for loss of HCl gas)
This then means that I got 3 times as much CaCO3 than what was should have been. The only mistake I could have made was in the original
weight of the dry seashells, but this is really highly unlikely - honestly, not by 250g?
[Edited on 18-11-2014 by CHRIS25]
‘Calcination… is such a Separation of Bodies by Fire, as makes ‘em easily reducible into Powder; and for that reason ‘tis call’d by some
Chymical Pulverization.’ (John Friend, Chymical Lectures London, 1712)
Right is right, even if everyone is against it, and wrong is wrong, even if everyone is for it. (William Penn 1644-1718)
The very nature of Random, Chance development precludes the existence of Order - strange that our organic and inorganic world is so well defined by
precision and law. (me)
|
|
|
gdflp
Super Moderator
Posts: 1320
Registered: 14-2-2014
Location: NY, USA
Member Is Offline
Mood: Staring at code
|
|
Is it possible that the shells you began with were mostly calcium oxide, and not calcium carbonate? If so, then you would get around 1.8mols of
calcium in solution. In addition, sodium bicarbonate will not precipitate calcium carbonate, it will result in calcium bicarbonate which is soluble
in water. The solution must then be evaporated, which causes the calcium bicarbonate to decompose, and any soluble salts will redissolve. If calcium
oxide was the starting material, this would result in 180g of CaCO3 which is closer to what you describe. Is it possible that there is still sodium
left in your final product? I would try a flame test on the suspect compound.
|
|
|
unionised
International Hazard
Posts: 5126
Registered: 1-11-2003
Location: UK
Member Is Online
Mood: No Mood
|
|
Interesting.
How carefully did you wash the precipitated CaCO3?
The first thing you need to do is repeat this experiment.
Incidentally, the chances of sea shells being made from something which reacts vigorously with water is, shall we say, slim.
[Edited on 18-11-14 by unionised]
|
|
|
CHRIS25
National Hazard
Posts: 951
Registered: 6-4-2012
Location: Ireland
Member Is Offline
Mood: No Mood
|
|
Hi, Firstly:
CaCl2+2NaHCO3=CaCO3+CO2+2NaCl
(by the way, I tasted the filtrate and it was deliciously salty, to confirm).
No Seashells are not made of Calcium Oxide, but the carbonate. So in effect I am reacting calcium carbonate with the HCl. Actually no, I did not
wash the precipitate at all actually, since my wife uses it to make chalk paint, (very expensive product in the shop), it actually works just as good
as the bought product.
@Unionised: bit confused on why you said this: ".....the chances of sea shells being made from something which reacts vigorously with water is, shall
we say, slim....."
Yes I will repeat with a very small amount, but I did this about 6 months ago and actually got the same results, though I never posted anything since
I was, again, making something quick for my wife's hobby and I was not concerned with analysing everything.
[Edited on 18-11-2014 by CHRIS25]
‘Calcination… is such a Separation of Bodies by Fire, as makes ‘em easily reducible into Powder; and for that reason ‘tis call’d by some
Chymical Pulverization.’ (John Friend, Chymical Lectures London, 1712)
Right is right, even if everyone is against it, and wrong is wrong, even if everyone is for it. (William Penn 1644-1718)
The very nature of Random, Chance development precludes the existence of Order - strange that our organic and inorganic world is so well defined by
precision and law. (me)
|
|
|
Little_Ghost_again
National Hazard
Posts: 985
Registered: 16-9-2014
Member Is Offline
Mood: Baffled
|
|
those are limpits by the look of it most the limpets I have used contain alot of magnesium salts, limpits are exposed to the sun and air for many
hours a day (they are tidal) personally I dont know the what but I do know the why. because of this exposure limpets excrete slightly different salts
for the shell as it needs to be harder than many, both because on environmental factors (tides,air,sun) and to prevent excessive predation.
I havnt got around to testing what the shell is made of but its definitely different to non tidal molluscs I will ask in the in house biologist if you
like.
I noticed this difference a while back when collecting shells for use, the very best for calcium carbonate are oysters or if you lucky like I am and
live near a beach where they wash up cuttle fish bones are very soft and mostly calcium carbonate. Other shells contain a mix of calcium,magnesium and
sodium salts. Give me a couple of weeks and I will post some results from different shells using a GC.
Dont ask me, I only know enough to be dangerous
|
|
|
Little_Ghost_again
National Hazard
Posts: 985
Registered: 16-9-2014
Member Is Offline
Mood: Baffled
|
|
I forgot to add, there are some good papers on shells and there variation in chemistry, join something like academic gateway
Dont ask me, I only know enough to be dangerous
|
|
|
DistractionGrating
Hazard to Self
Posts: 68
Registered: 3-4-2014
Member Is Offline
Mood: Precipitated
|
|
Seashells are most certainly made of calcium carbonate, as any knowledgeable marine aquarist can tell you. Both the amount of resulting CaCO3 and the
7 moles of HCl required point to an error in the original weight, don't you think?
|
|
|
Little_Ghost_again
National Hazard
Posts: 985
Registered: 16-9-2014
Member Is Offline
Mood: Baffled
|
|
Quote: Originally posted by DistractionGrating  | | Seashells are most certainly made of calcium carbonate, as any knowledgeable marine aquarist can tell you. Both the amount of resulting CaCO3 and the
7 moles of HCl required point to an error in the original weight, don't you think? |
I am not disputing there is alot of calcium carbonate there, what I am saying is there is a definite chemical difference or properties difference with
the shells of some species, rather than look a complete arse I will go search etc and come back with some references and results.
Its purely because I have used shells for other things that I noticed a difference myself with different shells.
So until I go get papers to cite etc its going to be pointless me saying much more. while i agree the maths is probably wrong, I am also aware there
are chemical differences with the shells he chose.
There is also something to do with the different forms like argonite (sp) and calcite admittedly both calcium carbonate.
[Edited on 18-11-2014 by Little_Ghost_again]
Dont ask me, I only know enough to be dangerous
|
|
|
aga
Forum Drunkard
Posts: 7030
Registered: 25-3-2014
Member Is Offline
|
|
There's a parallel experiment waiting for me to go and weigh in my shed.
Staring with ~100g shells in one pot and ~100g quarry stone (chalk) in the other.
So far one's a bit brown tinged, and the other smelt sulphur-y when reacting.
|
|
|
DistractionGrating
Hazard to Self
Posts: 68
Registered: 3-4-2014
Member Is Offline
Mood: Precipitated
|
|
Aragonite and Calcite are both CaCO3, but with different crystal lattices. I'm not entirely sure about seashells, but coral skeletons will be largely
CaCO3, but will also have some MgCO3 and a tiny amount of SrCO3 as well.
|
|
|
Little_Ghost_again
National Hazard
Posts: 985
Registered: 16-9-2014
Member Is Offline
Mood: Baffled
|
|
| Quote: Originally posted by aga | There's a parallel experiment waiting for me to go and weigh in my shed.
Staring with ~100g shells in one pot and ~100g quarry stone (chalk) in the other.
So far one's a bit brown tinged, and the other smelt sulphur-y when reacting. |
Out of interest are the shells all the same?
This could be a fun and interesting thing to look into, I live near several beaches and each is different, it would be interesting to take several
different shells and test them for there composition.
I also have a marine aquarium and my corals are pretty heavy users of calcium and magnesium (I have a calcium reactor and add trace minerals by pump
daily). Actually I am putting my reef tank up for sale, I have had it 4 years now and its superb! I spent a fortune on it and also designed and built
many of the control systems for it.
I doubt I will get a fraction of its value but I need the money for other stuff like my soap business  .
Its also costing a fortune to run because the electric here at home is very expensive. I will keep my freshwater tanks (for now anyway) and cant see
me ever giving up the dutch tank
Dont ask me, I only know enough to be dangerous
|
|
|
gdflp
Super Moderator
Posts: 1320
Registered: 14-2-2014
Location: NY, USA
Member Is Offline
Mood: Staring at code
|
|
| Quote: Originally posted by CHRIS25 | Hi, Firstly:
CaCl2+2NaHCO3=CaCO3+CO2+2NaCl
(by the way, I tasted the filtrate and it was deliciously salty, to confirm).
No Seashells are not made of Calcium Oxide, but the carbonate. So in effect I am reacting calcium carbonate with the HCl. Actually no, I did not
wash the precipitate at all actually, since my wife uses it to make chalk paint, (very expensive product in the shop), it actually works just as good
as the bought product.
@Unionised: bit confused on why you said this: ".....the chances of sea shells being made from something which reacts vigorously with water is, shall
we say, slim....."
Yes I will repeat with a very small amount, but I did this about 6 months ago and actually got the same results, though I never posted anything since
I was, again, making something quick for my wife's hobby and I was not concerned with analysing everything.
[Edited on 18-11-2014 by CHRIS25] |
No, actually sodium bicarbonate reacts with calcium in a two-step reaction. Calcium bicarbonate and sodium chloride are the initial two products.
Any precipitation which occurs is calcium carbonate since calcium bicarbonate isn't stable in solid form. But this reaction 2CaHCO3 --> CaCO3 +
H2O + CO2 doesn't happen immediately, it is a very slow reaction since CaHCO3 is stable in solution.
|
|
|
CHRIS25
National Hazard
Posts: 951
Registered: 6-4-2012
Location: Ireland
Member Is Offline
Mood: No Mood
|
|
@Distraction Grating. Actually the maths seems fine, the yield was 3.75moles Carbonate. The HCl used was 7moles. The initial balanced equation calls
for 2:1 HCl to CaCO3 respectively. Due to the fact that this was not an empirically designed process, rather something for my wife to put in her
paint, there may well have been excess HCl added without realising, and also I did not wash the precipitate. I am going to repeat the experiment with
determined accuracy with a couple of shells. But in any case, the original 100g of seashells is in no way mistaken, since I weighed out 300 grams and
could only find time to dissolve 100.
@Little Ghost something. Yes, this would be interesting actually, I appreciate the extra info. By the way, I did not know about the oysters, I can
get an un-ending supply of these as well close by. I will have a look at Gateway.
@Aga. Looking forward to your results.
@Gdifip. Ok I did not know that, but that is probably why it is not seen in any of the balanced equations, it really does not seem to me to be
important in attributing any help to solving the initial question. While I respect the chemistry here and am glad to be told, I don't see how it
helps. Although yes, it is definitely a slow process, it took hours for every 200 mLs of Calcium chloride to get the precipitate, foam foam foam,
tons of it, CO2 and Water naturally. Constant stirring with stir bar, but I emphasize absolutely no heat necessary.
[Edited on 18-11-2014 by CHRIS25]
‘Calcination… is such a Separation of Bodies by Fire, as makes ‘em easily reducible into Powder; and for that reason ‘tis call’d by some
Chymical Pulverization.’ (John Friend, Chymical Lectures London, 1712)
Right is right, even if everyone is against it, and wrong is wrong, even if everyone is for it. (William Penn 1644-1718)
The very nature of Random, Chance development precludes the existence of Order - strange that our organic and inorganic world is so well defined by
precision and law. (me)
|
|
|
unionised
International Hazard
Posts: 5126
Registered: 1-11-2003
Location: UK
Member Is Online
Mood: No Mood
|
|
| Quote: Originally posted by CHRIS25 |
@Unionised: bit confused on why you said this: ".....the chances of sea shells being made from something which reacts vigorously with water is, shall
we say, slim....."
[Edited on 18-11-2014 by CHRIS25] |
Because Gdflp wrote "Is it possible that the shells you began with were mostly calcium oxide, and not calcium carbonate? " and CaO reacts vigorously
with water.
|
|
|
Etaoin Shrdlu
National Hazard
Posts: 724
Registered: 25-12-2013
Location: Wisconsin
Member Is Offline
Mood: Insufferable
|
|
Oooooookay. Let's assume the mass of calcium alone in your shells was 100g, for the fun of it. That only nets you ~250g calcium carbonate with perfect
conversion.
You measured wrong, or you cleaned it wrong. How much NaHCO3 did you add?
[Edited on 11-19-2014 by Etaoin Shrdlu]
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
There has to be a weighing error somewhere, the discrepancy between theor. and actual yield is just ridiculously too high.
When you precipitate the CaCO3 make sure to do it from a fairly dilute solution of CaCl2, e.g. max 1 M. Na2CO3 is better here than NaHCO3 because
Ca(HCO3)2 is soluble in water
(calcium in bottled or tap water for instance. Ca bicarbonate is also the cause of scaling in kettles because on heating it decomposes, so over time
scale gets built up).
Allow the freshly formed CaCO3 to digest (stand) overnight before filtering. Wash with plenty hot water, finally with a bit of deionised water.
Dry thoroughly at at least 200 C for 2 hours.
|
|
|
aga
Forum Drunkard
Posts: 7030
Registered: 25-3-2014
Member Is Offline
|
|
| Quote: Originally posted by unionised | Because Gdflp wrote "Is it possible that the shells you began with were mostly calcium oxide, and not calcium carbonate? " and CaO reacts vigorously
with water.
|
I think CHRIS25 is pointing out that a CaO-shelled Underwater-dwelling mollusc would be homeless pretty soon.
|
|
|
CHRIS25
National Hazard
Posts: 951
Registered: 6-4-2012
Location: Ireland
Member Is Offline
Mood: No Mood
|
|
New Test Completed
One sad seashell, crushed and weighed: 10.1g Assumed a 0.101m for this.
HCl 36% 0.202m made up in 8M sstrength, total soln 25mLs
Covered and warmed, dissloved and filtered.
Resulting solution treated with Sodium bicarbonate, filtered and washed twice, dried and weighed.
Stoichiometric expectations:
0.101mol CaCl2 (11.2g) + 0.202mol NaHCO3 (16.9g) = CaCO3 0.101mol (20.2g)
Actual NaHCO3 required to complete precipitation: 13.13g ( 0.16mol) OR 17.35g (0.2mol) Was difficult to tell. But seeing that I did not
get 20g of carbonate I have to assume a figure of 13.13g completed the reaction.
Actual Yield CaCO3: 11.91g (0.12mol)
The Taste test:
The suspect batch is very salty, but this new test is completely free of any salty taste, tastes like perfect chalk.
Conclusion: I will wash 50g of the suspect batch, dry and weigh and taste. If there is a significant difference in weight then this is where my
problem was.
@Etaoin Shridu. """You measured wrong, or you cleaned it wrong. How much NaHCO3 did you add?"""" Total was 452g / 5.4 moles, but there was
consistency in the 200mL batches in that each batch took 73,75,84g sodium bicarbonate respectively. Yes I know, total seems overkill, but the final
precipitations were difficult to spot since I did this in batches of 500mLs then 200mLs, also I recognise now that I should add more water to each
batch. The CaCl2 solutions were far too concentrated.
@Blogfast. Hallo, I don't get why calcium bicarbonate would be a problem at all, just can't see it unless it prevents some of the Ca from the
CaCl2 from being joined to the carbonate because it hogs the carbonate in a disolved state in solution? Using Sodium Carbonate does look a
much more efficient idea; (I was going to do this, I have a ton of the stuff), just assumed that for some reason since everyone uses the bicarbonate
that must be the correct way. I certainly appreciate the heads up on doing this process more efficiently with your explanation, I need to know how to
improve the things that I do all the time, so thanks..
[Edited on 20-11-2014 by CHRIS25]
‘Calcination… is such a Separation of Bodies by Fire, as makes ‘em easily reducible into Powder; and for that reason ‘tis call’d by some
Chymical Pulverization.’ (John Friend, Chymical Lectures London, 1712)
Right is right, even if everyone is against it, and wrong is wrong, even if everyone is for it. (William Penn 1644-1718)
The very nature of Random, Chance development precludes the existence of Order - strange that our organic and inorganic world is so well defined by
precision and law. (me)
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Seems it was an extreme case of poor washing/occlusion. You'll need to BOIL the old batch with clean water for a bit, allow to stand overnight and
filter and wash again.
"just assumed that for some reason since everyone uses the bicarbonate that must be the correct way"
No: there are reasons to use bicarbonate and there are reasons to use carbonate: it's case dependent. For CaCO3 I'd use carbonate each and every time.
Request: don't abbreviate 'mol' to 'm'. It's like abbreviating 'cm' to 'c' or 'kg' to 'k': 'c' what? 'k' what? Respect our language, por favor! To try and be as unambiguous as possible makes good science.
[Edited on 20-11-2014 by blogfast25]
|
|
|
CHRIS25
National Hazard
Posts: 951
Registered: 6-4-2012
Location: Ireland
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by blogfast25 |
No: there are reasons to use bicarbonate and there are reasons to use carbonate: it's case dependent. For CaCO3 I'd use carbonate each and every time.
Request: don't abbreviate 'mol' to 'm'. It's like abbreviating 'cm' to 'c' or 'kg' to 'k': 'c' what? 'k' what? Respect our language, por favor! To try and be as unambiguous as possible makes good science.
[Edited on 20-11-2014 by blogfast25] |
What would be the reasons then for carbonate and bicarbonate?
As for abbreviation, I actually thought that it was acceptable to use a small 'm' for Mole and large 'M' for molarity in that this was an accepted
abbreviation. Was I wrong?
‘Calcination… is such a Separation of Bodies by Fire, as makes ‘em easily reducible into Powder; and for that reason ‘tis call’d by some
Chymical Pulverization.’ (John Friend, Chymical Lectures London, 1712)
Right is right, even if everyone is against it, and wrong is wrong, even if everyone is for it. (William Penn 1644-1718)
The very nature of Random, Chance development precludes the existence of Order - strange that our organic and inorganic world is so well defined by
precision and law. (me)
|
|
|
gdflp
Super Moderator
Posts: 1320
Registered: 14-2-2014
Location: NY, USA
Member Is Offline
Mood: Staring at code
|
|
'M' for molarity is an accepted abbreviation. However, 'mol' is the accepted abbreviation for mole, not 'm'. It's not an uncommon mistake, lots of
people often come to the same conclusion you did. In all honesty, it's not that big of a deal, everyone will most likely understand what you mean, it
just looks more professional the proper way.
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Assuming it's a carbonate you want to precipitate, which (carbonate or bicarbonate) to use depends on solubility of the corresponding hydroxide and
also on the bicarbonate if it exists. In the case of calcium the hydroxide is fairly soluble, the carbonate very insoluble and the bicarbonate fairly
soluble: using Na2CO3/K2CO3 is then recommended but bicarbonate also works.
If the hydroxide is very insoluble (e.g. Cu<sup>2+</sup> the
bicarbonate tends to precipitate the hydroxide or a hydroxycarbonate ('basic carbonate'), not the actual carbonate.
In some cases no carbonate can be precipitated: see Al<sup>3+</sup> and Fe<sup>3+</sup>, in those cases carbonates,
bicarbonates, hydroxide or ammonia all precipitate Al(OH)3 or Fe(OH)3.
These subtleties are caused by the fact that carbonate or bicarbonate solutions are alkaline, so they also contain OH<sup>-</sup> ions,
which kind of 'compete' (with the carbonate/bicarbonate ions) as to what exactly precipitates.
[Edited on 20-11-2014 by blogfast25]
|
|
|
DraconicAcid
International Hazard
Posts: 4334
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
How did you dry it?
I'd guess that it was still damp or hydrated with a yield like that.
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
CHRIS25
National Hazard
Posts: 951
Registered: 6-4-2012
Location: Ireland
Member Is Offline
Mood: No Mood
|
|
@gdifp. Ok, thanks. Good to know that then. mol it is.
@Blogfast. Thankyou, into my notebook then.
@DraconicAcid. Believe it or not it dries by the open fire for hours and hours, then the room stays heated all night due to neighbour's boiler against
the wall plus all the next day and so on, I usually allow two to three days depending on amounts and temp of room and taste buds! (Yes I have a habit
of eating my chemicals just to make sure I made the right one)
‘Calcination… is such a Separation of Bodies by Fire, as makes ‘em easily reducible into Powder; and for that reason ‘tis call’d by some
Chymical Pulverization.’ (John Friend, Chymical Lectures London, 1712)
Right is right, even if everyone is against it, and wrong is wrong, even if everyone is for it. (William Penn 1644-1718)
The very nature of Random, Chance development precludes the existence of Order - strange that our organic and inorganic world is so well defined by
precision and law. (me)
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by CHRIS25 | | @DraconicAcid. Believe it or not it dries by the open fire for hours and hours, then the room stays heated all night due to neighbour's boiler against
the wall plus all the next day and so on, I usually allow two to three days depending on amounts and temp of room and taste buds! (Yes I have a habit
of eating my chemicals just to make sure I made the right one)
|
That might not even be enough, you know. Most of us dry using directly applied heat, such as from an oven. For homemade CaCO3 a
domestic, kitchen oven will not be a problem for instance, as it's totally non toxic. An old ceramic kitchenware oven dish can serve as support.
|
|
|
| Pages:
1
2 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
