Smetje
Harmless
Posts: 3
Registered: 4-11-2013
Member Is Offline
Mood: No Mood
|
|
NO2 ion to create N2
Hi all
I'm trying to create a nucleating site for a poly-urethane mixture. While adding N2 in the reaction mixture seems logical, this poses quite
a challenge in terms of gas-size distribution.
That's what got me thinking towards chemical N2 creation.
Consider the following:
NH4Cl (aq) + KNO2 (aq) ---> N2 (g) + K+Cl- (aq)
+ 2 H2O (l)
I've chosen the above (theoretical) reaction because of the formation of water and the presence of K+ ions.
My question is quite simple:
Do you foresee any issues with this set-up, specifically the potential formation of NH4NO2 ?
I would like to dissolve the starting solids in glycerine (glycerol), to minimize the total water content. Concentration-wise I would not go over
15-25 mass%.
Thanks for your ideas and remarks.
-Smetjes
Edit small change in nomenclature and/or abbreviations. Excuses for the ambiguity.
[Edited on 4-11-2013 by Smetje]
|
|
|
woelen
Super Administrator
Posts: 8014
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
PU-mixture?
MEG? DEG? Are these mono ethylene glycol and the dimer?
And what do you mean with m% ? Is this mass percentage, or 1/1000th of a percent?
You should be more clear, all these acronyms and notations are not common knowledge.
|
|
|
vulture
Forum Gatekeeper
Posts: 3330
Registered: 25-5-2002
Location: France
Member Is Offline
Mood: No Mood
|
|
Nucleating site for what? Precipitation? PU forming reaction?
Are you trying to make foams?
One shouldn't accept or resort to the mutilation of science to appease the mentally impaired.
|
|
|
Smetje
Harmless
Posts: 3
Registered: 4-11-2013
Member Is Offline
Mood: No Mood
|
|
Hi Vulture
yes, the general idea is to make poly-urethane (let's abbreviate to PU) foams.
Reaction of the basic ingredients (polyol + di-isocyanate) would give a dense, coarse solid. Therefore it is typically "blown", by for example water
(which reacts with the isocyanate to form carbon dioxide) and other gasses. The solid (PU) consists of decahedronical cells - which I would like to
minimize through nucleation sites. Hence trying to create N2 with NO2.
In this set-up, the needed thermal energy would be available through the exothermic character of the PU reaction.
I hope this context is sufficient?
-Smetje
|
|
|
bbartlog
International Hazard
Posts: 1139
Registered: 27-8-2009
Location: Unmoored in time
Member Is Offline
Mood: No Mood
|
|
| Quote: | | specifically the potential formation of NH4NO2 |
Well, I think that's actually what you want ... isn't that on the pathway to N<sub>2</sub> production? KNO<sub>2</sub> doesn't
decompose by itself.
| Quote: | | Concentration-wise I would not go over 15-25 mass%. |
That may be quite a lot, no? But I don't know how light your intended foam will be.
Anyway, the system you propose (or one similar, using sodium nitrite plus ammonium chloride) has been used before to generate foams. I don't know
whether your proposed mixture will have solubility issues; if it does you may need to use a surfactant to create an emulsion.
A second problem is that this reaction does not proceed all that quickly without a catalyst. Acids are sometimes employed (HCl, acetic acid, citric
acid). However, since the reaction is exothermic, too low a pH can also cause problems / runaways. Whether this is a big issue for you may well depend
on the size of the foam structures you are trying to create. For larger items I would expect it to be very difficult to maintain a similar temperature
throughout the structure.
Finally, it sounds like you will need to make sure that this gas creation reaction runs to completion before your polymerization reaction, but not
*too* long before, so that it doesn't result in the destruction of an already solid polymer.
The less you bet, the more you lose when you win.
|
|
|
Smetje
Harmless
Posts: 3
Registered: 4-11-2013
Member Is Offline
Mood: No Mood
|
|
Thanks for the detailed reply, bbartlog!
| Quote: | | specifically the potential formation of NH4NO2 |
I'm slightly worried about the explosive character of this compound...
Quote: Originally posted by bbartlog  |
Anyway, the system you propose (or one similar, using sodium nitrite plus ammonium chloride) has been used before to generate foams.
|
Have you got information on these systems? I've never heard of N2 being used for anything but nucleation.
| Quote: Originally posted by bbartlog |
I don't know whether your proposed mixture will have solubility issues; if it does you may need to use a surfactant to create an emulsion.
A second problem is that this reaction does not proceed all that quickly without a catalyst. Acids are sometimes employed (HCl, acetic acid, citric
acid). However, since the reaction is exothermic, too low a pH can also cause problems / runaways. Whether this is a big issue for you may well depend
on the size of the foam structures you are trying to create. For larger items I would expect it to be very difficult to maintain a similar temperature
throughout the structure.
|
The solubility issue has been taken care of, through the use of commercially available surfactants.
I do not agree with you on the acids as catalysts however. See (wikipedia) Polyurethane catalysts about the tertiary amine catalysts. Lowering pH would inhibit the formation of the RO- anion.
Temperature distribution throughout the foam is an issue, though. However, heated moulds are shown to be effective.
| Quote: Originally posted by bbartlog |
Finally, it sounds like you will need to make sure that this gas creation reaction runs to completion before your polymerization reaction, but not
*too* long before, so that it doesn't result in the destruction of an already solid polymer. |
That is an issue I've been thinking about quite a lot. The only solution I've come up with so far, is to use a virtually non-catalysed PU reaction and
adding energy by mixing.
|
|
|
AJKOER
Radically Dubious
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Smetje | ....
That's what got me thinking towards chemical N2 creation.
Consider the following:
NH4Cl (aq) + KNO2 (aq) ---> N2 (g) + K+Cl- (aq)
+ 2 H2O (l)
................ |
I think it is more instructive to write the reaction as:
NH4Cl (aq) + KNO2 (aq) ---> KCl + NH4NO2
Now, research the product NH4NO2 and one will find a bit of concern in dealing with Ammonium nitrite in acidic aqueous conditions
(explosion hazard). The reason relates to stability issues of HNO2 (formed upon acidifying) which is prone to rapid gaseous decomposition
in anything other than cold dilute solutions.
The salt Ammonium nitrite has been described by some as acutely toxic, so keep this in mind.
So, I confirming the concerns expressed above about a runaway reaction plus some.
What about using CO2 in place of N2 via this path.
|
|
|
bbartlog
International Hazard
Posts: 1139
Registered: 27-8-2009
Location: Unmoored in time
Member Is Offline
Mood: No Mood
|
|
interesting point about the catalysis ... if I read the information right, the polymerization catalysts are all basic? Anyway, the decomposition
reaction of ammonium nitrite does not exactly *require* acidic conditions, it just proceeds faster under them. Which suggests that at least you have a
useful handle for speeding up one reaction at the expense of the other: if the nitrogen is being produced too fast, you can bump up the pH, and if
it's being produced too slowly, you can lower it. Of course it could be that there is no middle ground that will allow both reactions to proceed at a
reasonable rate, but maybe that's where temperature comes in.
Anyway, I found a little bit of information on this in "Production Chemicals for the Oil and Gas Industry" by Malcolm A Kelland; p268 is available for
preview via Google. A rather different application than yours, of course.
The less you bet, the more you lose when you win.
|
|
|
vulture
Forum Gatekeeper
Posts: 3330
Registered: 25-5-2002
Location: France
Member Is Offline
Mood: No Mood
|
|
I suspect you will run into trouble by using ammonium salts, since the catalysts are basic. You'll have NH3 formation, deactivation of your catalyst
and formation of nitrite salts. Seems like a mess to me.
One shouldn't accept or resort to the mutilation of science to appease the mentally impaired.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
