| Pages:
1
2 |
woelen
Super Administrator
Posts: 8016
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
What's the densest gas (or mix) you can create?
I intend to do a nice experiment in which an aluminium boat is floating on a dense gas. I have seen the YouTube film with a boat floating on SF6. This
is quite impressive, but not something easily done at home. SF6 is not a cheap and easy to obtain chemical.
SF6 is quite dense, its molecular weight is 146 gram/mole. Its density is appr. 5 times the density of air.
I also have considered volatile liquid compounds with high molecular weight, but these do not allow 100% pure gases without condensation. So, the
compound really must be a gas at let's say 20 C.
Some fairly dense alternatives, which can be made cheaply (e.g. a few liters of gas can be made for 1 euro or so):
Cl2 : 2.5 times the density of air.
C4H10: 2 times the density of air.
A somewhat more expensive alternative, but very easy to prepare is ONBr, which is almost 4 times as dense as air and can be made very easily by adding
solid NaNO2 to 40% HBr. This leads to formation of a nearly black liquid (aqueous solution of ONBr) and ONBr bubbles from this liquid (ONBr does not
dissolve in water that well). Food grade NaNO2 is dirt cheap for me, but unfortunately, HBr is quite expensive. I made some myself from NaBr and
half-concentrated H2SO4 and distilled this, but for a few liters of gas you need quite a lot of HBr. Another disadvantage of ONBr is its very dark
color. The gas is deep brown/red, much darker than Br2 and even darker than NO2. The gas also is quite toxic.
I already did experiments with this gas and it is amazing to see how it can be poured, almost like a liquid. It very slowly diffuses with air.
Are there any gases which have even better properties and are affordable (ONBr is at the border for me, the experiment would cost at least a few
euros)? So, gases, based on iodine or other expensive heavy elements are not interesting. Such gases I will not make in liter quantities. The gases
also must be achievable for a home chemist without special expensive equipment and the gas must be air-stable. Toxicity like Cl2 or NO2 is not a real
problem, as long as it is not insanely toxic like some chemical warfare gases.
[Edited on 3-3-13 by woelen]
|
|
|
neptunium
National Hazard
Posts: 990
Registered: 12-12-2011
Location: between Uranium and Plutonium
Member Is Offline
|
|
what about freons? some chloro fluoro alcane are non toxic, non flamable, dirt cheap, can be purchased by the gallon, and quite dense!
|
|
|
Metacelsus
International Hazard
Posts: 2539
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
Uranium hexafluoride is the densest known gas (in its gaseous phase, which is above 57 C at 1 atm). Tungsten hexafluoride is the densest known gas at
STP (11x denser than air). However, you probably won't be able to make any of these, unless you can work with fluorine.
|
|
|
neptunium
National Hazard
Posts: 990
Registered: 12-12-2011
Location: between Uranium and Plutonium
Member Is Offline
|
|
Quote: Originally posted by Cheddite Cheese  | | Uranium hexafluoride is the densest known gas (in its gaseous phase, which is above 57 C at 1 atm). Tungsten hexafluoride is the densest known gas at
STP (11x denser than air). However, you probably won't be able to make any of these, unless you can work with fluorine. |
he mentioned cheap and readily availlable .
|
|
|
kristofvagyok
National Hazard
Posts: 659
Registered: 6-4-2012
Location: Europe
Member Is Offline
Mood: No Mood
|
|
That idea with UF6 smiled me. Would be interesting to work with a gas like that(:
What about chloroethane? It is bit more dense than air, but it could be easily made, could be handled safe and it's cheap. Or freons... On ebay a lot
freon containing fire exhauster could be found, sometimes for dirt cheap.
I have a blog where I post my pictures from my work: http://labphoto.tumblr.com/
-Pictures from chemistry, check it out(:
"You can’t become a chemist and expect to live forever." |
|
|
phlogiston
International Hazard
Posts: 1379
Registered: 26-4-2008
Location: Neon Thorium Erbium Lanthanum Neodymium Sulphur
Member Is Offline
Mood: pyrophoric
|
|
xenon MW = 131 (d = 5.89)
krypton MW = 83.3 (d=3.75)
methylbromide, MW = 94.94 gram/mole
On a very hot summer day (bp=42 deg C) methyliodide would ofcourse be even denser (MW= 141.09), but given the all-time highest temperature in the
Netherlands was 38.6 deg C in Warnsveld (1947), this will only work in the hot attic of your house, not outside, and I'm not sure you want to do that
with such toxic gasses 
-----
"If a rocket goes up, who cares where it comes down, that's not my concern said Wernher von Braun" - Tom Lehrer |
|
|
MrHomeScientist
International Hazard
Posts: 1806
Registered: 24-10-2010
Location: Flerovium
Member Is Offline
Mood: No Mood
|
|
I was going to suggest xenon as well. If I remember right, it is used occasionally in welding.
I am fortunate in that I actually get to work with SF6. You're right, it is not cheap and is only sold by the big chemical suppliers. I do an
educational outreach science stage show for kids, and breathe this as one of my demos. It's really incredible how low your voice gets, and pretty
shocking to the audience every time. I love this demo because everybody knows about helium, but very few have heard of SF6 so it's always very
surprising (and hilarious).
I've also floated balloons of regular air in a beaker full of the gas. It works great, and is very eerie. I always wanted to scale it up to a fish
tank, but that would be some serious cash!
Edit: Xenon is also safe to breathe, so if you get your hands on some you should definitely try that out "Safe" being relative of course, these gases are simple asphyxiants.
[Edited on 3-4-2013 by MrHomeScientist]
|
|
|
woelen
Super Administrator
Posts: 8016
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Xenon also is very expensive. Its price is expressed in euros per gram! Not something affordable for this kind of experiments.
Suitable freons have densities in the order of 2 to 3 times the density of air. I am afraid that the densest fairly affordable gas for me indeed is
ONBr. Making 2 liters and floating a balloon in the gas should be possible.
|
|
|
Fantasma4500
International Hazard
Posts: 1681
Registered: 12-12-2012
Location: Dysrope (aka europe)
Member Is Offline
Mood: dangerously practical
|
|
in my country argon is considered directly toxic, still shaking my head over this statement....
sounds really incredible.. need to go watch this experiment.. my bet would be some long very complicated gasses, but how long chemical formulas can
they get when youre thinking relatively OTC.. that might be the problem..
|
|
|
Pok
potassium Prometheus
Posts: 176
Registered: 5-12-2010
Member Is Offline
|
|
HI is 4.5 times as dense as air. And iodides aren't soo expensive. If the whole iodine is converted to HI you will need about 35 grams KI for 5 Liters
HI.
Here you can see many gases with their densities (you can sort them by density ("Dichte")):
http://de.wikibooks.org/wiki/Tabellensammlung_Chemie/_Dichte...
Almost all high density gases are either instable (e.g. TeH2) or impossible to make at home (halocarbons). But I didn't know that something like ONBr
exists. So maybe there are some other strange alternatives beside that.
If you only want to let a balloon flow then even CO2 should be sufficient.
[Edited on 4-3-2013 by Pok]
|
|
|
MrHomeScientist
International Hazard
Posts: 1806
Registered: 24-10-2010
Location: Flerovium
Member Is Offline
Mood: No Mood
|
|
I forgot about CO2 - I've also floated soap bubbles on that gas before. Simply place dry ice in a bowl, let sit for a few minutes to fill with gas,
and gently blow bubbles over top of it so that they fall down into the bowl. I tried it with a tiny balloon of air, but that was too heavy.
I think if you made ONBr, the preparation and appearance of the gas would be just as interesting as floating things in it!
|
|
|
Adas
National Hazard
Posts: 711
Registered: 21-9-2011
Location: Slovakia
Member Is Offline
Mood: Sensitive to shock and friction
|
|
| Quote: Originally posted by woelen | Xenon also is very expensive. Its price is expressed in euros per gram! Not something affordable for this kind of experiments.
Suitable freons have densities in the order of 2 to 3 times the density of air. I am afraid that the densest fairly affordable gas for me indeed is
ONBr. Making 2 liters and floating a balloon in the gas should be possible. |
I think it would not be possible becuase the ONBr would react rapidly with the balloon.
Rest In Pieces!
|
|
|
woelen
Super Administrator
Posts: 8016
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Interesting list of gases. All those fluorine-containing gases have amazing density, e.g. something like C4F10 or TeF6. Nice stuff, but as you already
said, not something you can make at home. I think that the densest gas which I can make at home and which is air stable and cheap is ONBr. HI is not a
real good alternative. It fumes in contact with air and very quickly becomes a nasty acidic wet mess. ONBr is stable in contact with air and does not
fume. It has the same smell as ONCl, somewhat 'spicey', quite different from Cl2 or Br2.
I made a little movie of pouring ONBr from an erlenmeyer. It nicely shows the density of the gas and how well it remains separated from air (watch the
content of the erlenmeyer).
http://www.homescience.net/chem/ONBr.avi
Beware, it is a big file (almost 40 MByte), it must be processed and compressed before it will be available on my website (lateron I will replace the
link by another better suited file). I already post it here, so that you can see how the gas behaves. The black liquid in the erlenmeyer is not Br2,
but appr. 40% HBr, to which some solid NaNO2 is added. The black color is due to the ONBr, dissolved in this liquid.
[Edited on 4-3-13 by woelen]
|
|
|
bhattshivamm
Harmless
Posts: 11
Registered: 24-2-2013
Location: India
Member Is Offline
Mood: No Mood
|
|
As i had read before some time, methylene iodide (diiodo methane - CH2I2 is the densest liquid known (except mercury)... so i
assume its vapors might also be so much dense... (just assuming)
|
|
|
Glucose Oxidase
Harmless
Posts: 37
Registered: 31-12-2012
Member Is Offline
Mood: Researching Alchemy
|
|
I think i must warn you that if you want to use argon or xenon they might contain some radon impurities which causes infertility (common among argon
welders) so use it with some protection ............ best wishes 
|
|
|
neptunium
National Hazard
Posts: 990
Registered: 12-12-2011
Location: between Uranium and Plutonium
Member Is Offline
|
|
the amount of radon in xenon and argon is so small t and its radioactive half life so short (about 4 days) that you would have to inhal so much that
the lack of oxygen will kill you long before any radiation sickness symptoms....its like saying bananas contain the dangerous isotope K40! you`ll be
fine
|
|
|
watson.fawkes
International Hazard
Posts: 2793
Registered: 16-8-2008
Member Is Offline
Mood: No Mood
|
|
Got a citation for that? Seems mighty unlikely. There are plenty of ordinary chemical hazards in welding;
you'll have to supply a citation that links to radon specifically.
Radon has a half-life of 3.8 days and its daughter isotopes have half-lives in minutes. If you put some radon in a tank, it's almost all gone within a
couple of months. Because there's no uranium-bearing rock formation in the tank to replenish the radon, it simply goes away.
|
|
|
phlogiston
International Hazard
Posts: 1379
Registered: 26-4-2008
Location: Neon Thorium Erbium Lanthanum Neodymium Sulphur
Member Is Offline
Mood: pyrophoric
|
|
While reduced fertility has indeed been found repeatedly among welders, it is more commonly believed to be linked to inhalation of metal fumes.
-----
"If a rocket goes up, who cares where it comes down, that's not my concern said Wernher von Braun" - Tom Lehrer |
|
|
AndersHoveland
Hazard to Other Members, due to repeated speculation and posting of untested highly dangerous procedures!
Posts: 1986
Registered: 2-3-2011
Member Is Offline
Mood: No Mood
|
|
I am sure there are denser gases, but they are likely very poisonous. S2F10, for example, boils at 30.1 °C (around the temperature outside on a warm
day). It would be 9 times heavier than air.
Xenon gas is 90% as dense as SF6. Xenon has mild anesthetic qualities due to its physical properties, like several other well known anesthetic
compounds (nitrous oxide and chloroform vapors, for example). (the physical effects are probably are due to high solubility in lipids)
If you have ever seen a balloon filled with xenon being dropped, it is conspicuosuly heavy for a gas.
http://www.youtube.com/watch?v=QLrofyj6a2s
[Edited on 6-3-2013 by AndersHoveland]
|
|
|
Glucose Oxidase
Harmless
Posts: 37
Registered: 31-12-2012
Member Is Offline
Mood: Researching Alchemy
|
|
| Quote: | Got a citation for that? Seems mighty unlikely. There are plenty of ordinary chemical hazards in welding; you'll have to supply a citation that links
to radon specifically.
Radon has a half-life of 3.8 days and its daughter isotopes have half-lives in minutes. If you put some radon in a tank, it's almost all gone within a
couple of months. Because there's no uranium-bearing rock formation in the tank to replenish the radon, it simply goes away. |
actually i have no citation . My father , a urologist, told me so but i never researched it on the internet or in any book
Protection is better than cure so i just want woelen to be careful
[Edited on 8-3-2013 by Glucose Oxidase]
|
|
|
garage chemist
chemical wizard
Posts: 1803
Registered: 16-8-2004
Location: Germany
Member Is Offline
Mood: No Mood
|
|
The perfluorocarbons are low-boiling and have an extremely high vapor density. Simply heat perfluorohexane (C6F14) to a boil and you have a gas phase
with a molar mass of 338g, around 14g per liter.
Otherwise, try boiling some carbon tetrachloride and try to float your aluminum foil boat on these vapors.
|
|
|
DraconicAcid
International Hazard
Posts: 4339
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
If the vapour is hotter than the room, it won't sit nicely in the tank, but will mix due to convection currents.
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
AndersHoveland
Hazard to Other Members, due to repeated speculation and posting of untested highly dangerous procedures!
Posts: 1986
Registered: 2-3-2011
Member Is Offline
Mood: No Mood
|
|
Perfluoropentane boils at 30 °C (warm day), and the vapors are about 10 times denser than air.
| Quote: Originally posted by garage chemist | | The perfluorocarbons are low-boiling and have an extremely high vapor density. Simply heat perfluorohexane (C6F14) to a boil and you have a gas phase
with a molar mass of 338g, around 14g per liter. |
Or put the entire demonstration inside an enclosed transparent container, with a little hole. Then add helium and heat the inside of the container to
56 °C. Then preheat the fluorohexane and introduce it into the container. Then finally, introduce the aluminum foil boat through an opening in the
middle. 56 °C air feels like the inside of an oven. Might use an insulated mitten or a pincher stick to introduce the boat.
[Edited on 9-3-2013 by AndersHoveland]
|
|
|
franklyn
International Hazard
Posts: 3026
Registered: 30-5-2006
Location: Da Big Apple
Member Is Offline
Mood: No Mood
|
|
www.youtube.com/watch?v=hbIXWe9IZgo
I think obtaining funding source is the problem.
SF6 is hard to beat for utility and safety.
www.youtube.com/watch?v=XjCmwuGKR6g
The entire list of gasses lighter than air fits on one line :
H2 , He , Ne , CH4 , NH3 , HF , B2H6 , C2H2 , C2H4 , HCN , N2 , and CO.
All the other gasses are heavier than air. Argon, CO2 , ethane (C2H6)
propane (C3H8) , butane (C4H10) , all the Freons ( CF4 , C2F6 , C2F4H2
CF2Cl2 ) and others.
The density of a gas is proportional to the sum of the atomic weights in
one molecule. Individual atoms: C=12, N=14, O=16 gm/mole.
So molecules: N2=28 and O2=32 , and so air ( 80% N2 + 20% O2 )
averages abut 29 gm/mole.
CO2 = 12+16+16 = 44 , definitely heavier than air. All these gasses have
the same number of molecules in a given volume, but the molecules weigh
different amounts. So a heavy molecular weight makes a heavy gas.
- Jim Swenson
From here _
www.newton.dep.anl.gov/askasci/chem03/chem03251.htm
www.wisc-online.com/objects/ViewObject.aspx?ID=GCH5704
http://yeroc.us/calculators/gas-density.php
www.engineeringtoolbox.com/specific-gravities-gases-d_334.ht...
www.engineeringtoolbox.com/gas-density-d_158.html
Organics such as Xylene have reasonable density
Boiling point (760 torr): 135 to 145 ºC
Vapor density (air = 1 at boiling point of xylene): 3.7
Ignition of the combustible vapor is a consideration.
Flash point: 27 to 32 ºC (81 to 90 ºF).
Autoignition temperature: 464 ºC (867 ºF).
Flammable limits in air (percent by volume): Lower, 1 ; upper, 7.
From here _
www.osha.gov/SLTC/healthguidelines/xylene/recognition.html
www.engineeringtoolbox.com/explosive-concentration-limits-d_...
______________________________________________
Ozone depleteing Freons are an alternative
http://en.wikipedia.org/wiki/R-114
http://en.wikipedia.org/wiki/R-123
Halocarbons generally are quite dense
http://en.wikipedia.org/wiki/List_of_refrigerants
One having a boiling point around room temperature should work.
.
|
|
|
kristofvagyok
National Hazard
Posts: 659
Registered: 6-4-2012
Location: Europe
Member Is Offline
Mood: No Mood
|
|
This is also not the cheapest reaction but it's really easy to make. Trifluoroacetonitrile could be easily made via mixing P2O5 with
trifluoroacetamide and dry distill it. A dense gas (95g/mol) will come over what could be easily condensed with liquid nitrogen to a white solid if
needed.
Trifluoroacetamide could be easily made from TFA and ammonia, and I think P2O5 is also not an impossible thing to get.
I have a blog where I post my pictures from my work: http://labphoto.tumblr.com/
-Pictures from chemistry, check it out(:
"You can’t become a chemist and expect to live forever." |
|
|
| Pages:
1
2 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
