Organikum
resurrected
Posts: 2337
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: frustrated
|
|
Sealing Gasgenerators
One of my bigger problems is solved, the sealing of generators of toxic gasses including the wash and drying-train without the use of expensive
wash-bottles with grounded joints or so.
Good experiences were already made by using PLASTILIN, but it was not absolute satisfying regarding adhesion.
The solution now is - mineral pitch aka bitumen aka asphalt.
Available at the next hardware store for sealing roofs.
Have phun, enjoy!
ORG
|
|
|
Tacho
National Hazard
Posts: 582
Registered: 5-12-2003
Member Is Offline
Mood: No Mood
|
|
Plastilin is a great idea for sealing temporary setups! I never thought of that.
I sugest the use of hot-melt glue. I don't know if this name is used internationally. It is the plastic rod that you melt in a pistol. As you
squeeze the trigger it comes out of an orifice as molten plastic.
Its adhesion is much better than plastilin, but not as good as pitch.
Something else: pure pitch behave as a liquid if given enough time. I remember this 50 kg bag that had a hole in it. Looking at the scene you would
think it was a bag of black paint that had leaked, making a trail along the shelves and a leaving pool on the floor, but it was all solid.
|
|
|
Organikum
resurrected
Posts: 2337
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: frustrated
|
|
Tacho wrote: | Quote: |
I sugest the use of hot-melt glue
|
NO! NO! NO!
Forget it! Dont even think of it!
The chemical resistance of this is zero, nada, nothing, not existing. Perhaps against water for 30 minutes or so.
And NO SILICONE!
Dont make yourself unhappy please. Pitch and Plastilin - they work are cheap and everywhere.
| Quote: |
Something else: pure pitch behave as a liquid if given enough time. I remember this 50 kg bag that had a hole in it. Looking at the scene you would
think it was a bag of black paint that had leaked, making a trail along the shelves and a leaving pool on the floor, but it was all solid
|
Yes. Same for glass. Give it some hundred or thousand years ..... 
But in your example its mainly the pressure which causes this effect.
|
|
|
Cyrus
Hazard to Others
Posts: 397
Registered: 24-4-2004
Location: Ancient Persia
Member Is Offline
Mood: No Mood
|
|
I thought tar might be a little hard to clean off of glassware, can I just use alchohols or acetone?
|
|
|
Tacho
National Hazard
Posts: 582
Registered: 5-12-2003
Member Is Offline
Mood: No Mood
|
|
| Quote: |
NO! NO! NO!
Forget it! Dont even think of it!
|
Threw it in the garbage using tweezers! I'll never touch the evil thing again!
|
|
|
Organikum
resurrected
Posts: 2337
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: frustrated
|
|
Toluene and xylene remove tar and bitumen quite well. Alcohols dont.
|
|
|
janger
Harmless
Posts: 40
Registered: 20-8-2004
Member Is Offline
Mood: No Mood
|
|
I have a few rolls of a type of soft butyl rubber. Ozone resistant. Water resistant. Electrolyte resistant. Fairly heat resistant. Sticks well if need
be, else can make temporary seals. Just used it on a chlorate cell with a low positive pressure inside. No chlorine smell at all.
Thanks, say my lungs and throat.
Dave
|
|
|
Saerynide
National Hazard
Posts: 954
Registered: 17-11-2003
Location: The Void
Member Is Offline
Mood: Ionic
|
|
Whats wrong with glue gun or silicone?  I thought silicone was quite chemical
resistant
And I agree. Plasticine/Plastilin works wonders Its just too oily and slips
off everything, but once its taped in place, its not bad 
"Microsoft reserves the right at all times to monitor communications on the Service and disclose any information Microsoft deems necessary to...
satisfy any applicable law, regulation or legal process"
|
|
|
blazter
Hazard to Self
Posts: 71
Registered: 3-9-2002
Member Is Offline
Mood: No Mood
|
|
There is a plastic material that comes on a roll, and is similar in properties to silly putty, not to mention very very sticky. I really don't
know what sort of chemical resistance the stuff has, but its very sticky and makes air tight seals with just about anything. I used to use it at work
all the time to make vacuum tight seals with plastic tubing, plastic film to molds, etc, etc. The stuff worked well to temporarly seal up a makeshift
aspirator that I cobbled together with some plumbing parts.
Apparently a similar type of material is used to seal beads around windows to window frames, and is known in the fiberglass industry as "monkey
glue".
|
|
|
chloric1
International Hazard
Posts: 1140
Registered: 8-10-2003
Location: GroupVII of the periodic table
Member Is Offline
Mood: Stoichiometrically Balanced
|
|
I agree
| Quote: |
NO! NO! NO!
Forget it! Dont even think of it!
The chemical resistance of this is zero, nada, nothing, not existing. Perhaps against water for 30 minutes or so.
And NO SILICONE!
|
I agree I am having problems with my Chlorine genrator becuase I used hotmelt glue. It does not do didly
squat!
Fellow molecular manipulator
|
|
|
JohnWW
International Hazard
Posts: 2849
Registered: 27-7-2004
Location: New Zealand
Member Is Offline
Mood: No Mood
|
|
Whatever it is, it would not stop the very lightest gases like H2 or He from leaking. They can diffuse through almost anything organic.
John W.
|
|
|
janger
Harmless
Posts: 40
Registered: 20-8-2004
Member Is Offline
Mood: No Mood
|
|
| Quote: | Originally posted by JohnWW
Whatever it is, it would not stop the very lightest gases like H2 or He from leaking. They can diffuse through almost anything organic.
John W. |
Hmmm, the butyl stuff I have is similar to what's used to seal electrolytic capacitors. Apparently resists diffusion of gases very well.
|
|
|
Mendeleev
Hazard to Others
Posts: 237
Registered: 25-12-2003
Location: USA
Member Is Offline
Mood: stoned
|
|
This tar interests me because I am planning to generate about 5 mols of Cl2 for a reaction. I am using was bottles consisting of erlenmeyer flasks
and corks. I suppose that to seal my apparatus I would simply assemble the flasks/corks and apply the pitch on the outside, or should the cork be
dipped into the molten pitch to make it gas proof? Or would you simply take a chunk of pitch and stick it onto the flask?
[Edited on 27-8-2004 by Mendeleev]
Trogdor was a man. A dragon man. Or maybe just a dragon. . .
|
|
|
Organikum
resurrected
Posts: 2337
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: frustrated
|
|
Sealing/impregnating corks the way you described it is the way to go, by dipping them into molten pitch.
You can also make a undersized stopper from plaster of paris and fix this with pitch as a seal - incorporate the tubing and its perfect.
In both cases seal from the outside too use enough pitch/asphalt to keep elasticity on the seals for the tubing.
A pitch-only seal may or maynot work, this depends on your pitch and the diameter of the opening. I prefer and advise to use a solid inlay though.
You should by NO WAY test your setup with a 6 mole load on first run. And you have to test it - first a short, 10minutes test and then consecutive
longer ones. Sounds boring. Is less boring than to fuckup a x-mole reaction.
Been there done that
|
|
|
Mendeleev
Hazard to Others
Posts: 237
Registered: 25-12-2003
Location: USA
Member Is Offline
Mood: stoned
|
|
I went down to my local hardware store, and I didn't find any pitch, but there were roof sealants with all sorts of elastic polymers, and they
were labeled as water proof, I don't know if that's good enough or will chlorine leak through these?
Edit: I went to the hardware store again and found the tar, it's not in the roof section it's in the section with concrete and its used for
asphalt not roofs.
[Edited on 28-8-2004 by Mendeleev]
Trogdor was a man. A dragon man. Or maybe just a dragon. . .
|
|
|
Mendeleev
Hazard to Others
Posts: 237
Registered: 25-12-2003
Location: USA
Member Is Offline
Mood: stoned
|
|
Just to check back in, the pitch is a bad idea. Why? Because it doesn't melt. I heated a 250 mL beacker one third full of pitch on a hot plate
on max setting for two hours and it was still solid. When I took matters into the hands of my trusty torch it simply caught on fire. I'm
sticking to good old teflon tape and rubber cement.
Trogdor was a man. A dragon man. Or maybe just a dragon. . .
|
|
|
Hermes_Trismegistus
National Hazard
Posts: 602
Registered: 27-11-2003
Location: Greece, Ancient
Member Is Offline
Mood: conformation:ga
|
|
Pitch is not standardized, it can come as goo or as chips, the chips have all the higher fractions evap'ed out.
The goo turns into pitch over time or with application of heat.
it's used up here by the indians, trying to revive the old arts, for making birchbark canoes.
Drop a little random solvent into the pitch to gooey it up a little, it takes time to absorb in though
The indians here use white gasoline,(coleman fuel) in a bucket with the chips for a week or two, they use way too much, then boil off the excess over
a fire that was banked to embers, until they reach the proper consistency.
It bursts into flame once in awhile, sorta funny seeing them dance around the flaming bucket of pitch cursing and swearing.
When the heat is applied to the canoe again (in a smokehouse) the solvent fumes away leaving hard pitch. When the seams crack from hard use they
either glob on more pitch, or just use a little white gas on the seam and smear it a little and then roast it off with a bic lighter.
It's really funny seeing them slap out the flaming patch of pitch with the palm of their hand and then jump up and down cursing and swearing.
Whatever the "old" ways were, they are slow to be rediscovered.
Arguing on the internet is like running in the special olympics; even if you win: you\'re still retarded.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
