Saganism
Harmless
Posts: 18
Registered: 25-9-2012
Location: Ozark mountains
Member Is Offline
Mood: No Mood
|
|
Distillig ethanol from corn mash. Help?
So I have a glass kit, no metal/copper bull. I've had a mash going for the past 2 weeks that is very potent with alcohols. Well, I setup for
fractional distillation and used a water bath. Well my cimarec hot plate/stirrer combo was literally at its max capacity of what is apparently 540
Celsius, which I know is false, cause I took a thermometer to it and it only read up to 300 Celsius. On top of the disappointment of an apparently
really bad plate which cost me 340$(never buy one of these), the water bath wouldn't even boil after 2 hours? Didnt even get past 90 Celsius. So then
finally it boiled a bit(not to mention I had boiling stones in both solutions(water bath, still flask) from the beginning. Still, through the water
bath boiling nothing for 30 more minutes. Well I was rushed away from this to go to a wedding so I couldn't finish. Before I left though I checked the
flask, and some sort of white solution had halfway hardened into some sort of emulsion?? Wtf? Turns out the boiling stones in the still flask had been
literally caked to the bottom. Could I get some tips? Is a bunson burner better for this? I'm extremely agitated
Just trying to figure some stuff out you know?
Aren't we all?
|
|
|
CaliusOptimus
Hazard to Self
Posts: 96
Registered: 10-6-2011
Member Is Offline
Mood: Subjectively Objective
|
|
Lab hotplates don't put out much heat compared to cooking hotplates. They are more geared toward even heating characteristics. You don't need stirring
for this kind of thing anyway, but insulating your bath with fiberglass should get you up to 150c range no problem.
Use an oil bath on a $15 kitchen hotplate, you won't be disappointed.
[Edited on 7-10-2012 by CaliusOptimus]
|
|
|
violet sin
International Hazard
Posts: 1480
Registered: 2-9-2012
Location: Daydreaming of uraninite...
Member Is Offline
Mood: Good
|
|
so what all did you do to the mash before you tried to still it off? from what I read, and tips from the brew store owner, say that it
has to be clarified unless you want crud to gum up your boiling flask. like boiling down a thinned out corn soup  eventually it boils down to a gum. and if you are doing glass distillation set, maybe a sand bath would be best. you
can stick a thermometer in the sand next to the flask to easily monitor temp, and you don't have to worry about heat losses from you water bath
boiling off. you only have to get it to ~80'C. -starts coming over at like 65'C, fine tune it to about 78'C- paraphrased from book
I bought a book and a few things to get started, and being that I am a beginner, I wonder how much experience you have with this? not to
be a jerk, but 2 weeks for the mash is a bit longer than recommended no? the turbo yeast I got said 48 hrs for 14% and after 5 days a full 20%. all
you have to add is water, sugar, and optionally yeast nutrients( comes in packet with mine). I didn't wanna use corn b/c of the mess but there is
nothing wrong with going that route. clarify it and still, or use something stainless for vessel that can just be cleansed thoroughly with food grade
chems. also sold in a brew shop. I bought a stainless beer keg for my boiler.
side note, I found a "acid cleaner no. 5" there at the store, and looked up the msds, its 5% phosphoric acid and 30-35% nitric. blue liquid in 1 gal
botttle. just fyi.
I have only read up a lot so deff not trying to act all know it all. there is stuff every where online to read, and the book I got is
called "moonshine made simple and the still makers manual" -byron ford- ISBN 0-473-07404-4. was only like 12$ and 125pg cover to cover. it has a LOT
of info though, including still basic designs and operations, essential oil production and more. I highly recommend it. if not then consult a local
brew shop owner. they (in my experience) are really nice and you can ask all kinds of questions w/o having to worry too much about what you say.
they are use to it.
good luck
|
|
|
vmelkon
National Hazard
Posts: 669
Registered: 25-11-2011
Location: Canada
Member Is Offline
Mood: autoerotic asphyxiation
|
|
I would not do that. If your glassware has ground joints, there will be some ethanol vapor at the joints. Always use electric heaters when working
with flammable organic liquids.
|
|
|
Fossil
Hazard to Others
Posts: 131
Registered: 4-4-2012
Location: Canada
Member Is Offline
Mood: No Mood
|
|
Purification of ethanol from an alcoholic wash
I would give you a full write up of my experiences, but I honestly don't have the time right now, so i'll refer you to the place where I learnt a lot
of what I know. The rest coming from experimentation.
http://homedistiller.org/
http://homedistiller.org/forum/
A few tips I'll give are:
-Have copper somewhere in your fractioning column or in your still (where it will interact with the alcohol vapors. The copper reacts with the
congeners (fusel oils) and helps to remove some of the foul smell/taste you will encounter.
-Use a fractioning column.
-Heat slowly, especially once the vapors reach the 70c range. I try to keep my thermometer in the high 60's-low 70's for as long as possible.
-If your aim is to get a neutral alcohol, do not go over 80c-81c
-Never distill a wash that has yeast left in it. Always rack away the yeast. The heat will break the yeast down realeasing all kinds of foul
smells/tastes.
I am by no way an expert and these tips are purely from experience. Make sure to do a lot of reading on the subject, you won't regret it.
|
|
|
Saganism
Harmless
Posts: 18
Registered: 25-9-2012
Location: Ozark mountains
Member Is Offline
Mood: No Mood
|
|
Should I use a sep funnel and separate my layers draining the bottom? Will the alcohol layers be on top? And What i did to the mash before I stilled
it, was filtered out all of the corn meal and such only leaving behind liquids but when i shake it up a bit and it eventually settles out, there are
two layers? One on the bottom is obviously gum like. How do I 'rack' out the yeast? And again yes, I'm going for neutral ethanol. Obviously I'm a
beginner, didn't think that needed to be stated considering here I am asking for help?
Fossil, you say you like to keep your thermometer in the high sixties low seventies, I assume this is for the purpose of stilling off all of the
Methanol? I have no copper and I've read in places where it can be done without the copper, I'm going for neutral ethanol so the copper isn't exactly
necessary is it? If I must, could copper sulphate be used for this in the way a drying agent would be used? Just a simple swirl or two and let it sit
sort of thing? or what? Lots of questions.. sorry. I have a festival I'm going to in a few days and I really need at least a liter to go out there
with. ALSO. if someone could give me a recipe to use in a 5 gal bucket that would be awesome, as well as a recipe that actually works with only sugar,
water, and yeast?? That would be great. But how long does that take? This mash I made last was a 4 gal pot and I put 8lbs of corn meal and equal parts
sugar and about 21 grams of yeast. Red star to be exact. I'm looking for the most efficient formula, as is everyone I guess.
Just trying to figure some stuff out you know?
Aren't we all?
|
|
|
Bot0nist
International Hazard
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
"Rack" simply means to siphon all the liquids off the settled, dormant yeast.
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
|
Dr.Bob
International Hazard
Posts: 2734
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
I did this once in a biofuels class, it took almost 2 hours just to get it up to temperature with a large hotplate. Water (which the mash is ~ 90%)
has an enormous heat capacity so it takes forever to boil a large amount.
Plus you will need to clarify first, just pour off the top fluids leaving most of the yeast behind. You can then pour the yeast goo in a small glass
and then pour off more fluid back.
This process took over 5 hours for a 10 L batch, to get about 1L of EtOH, which was about 90%, but using a stainless steel fractionating column.
This is not a trivial process, just like many other things.
|
|
|
cyanureeves
National Hazard
Posts: 744
Registered: 29-8-2010
Location: Mars
Member Is Offline
Mood: No Mood
|
|
i did it with a crock pot warmer .the two part ones not the single self heating pot but first you have to separate the liquid from the solid. i also
didnt use copper tubing but instead used a couple of heat resistant silicone tubes i got from the inside bottom of old regular coffee makers.i
attached aluminum tubes in segments along with the silicone tubes and hung it on a string. i put the mash in a tin gallon xylene can and wrapped it in
aluminum foil. water boils at 212 deg. so just under was enough to send ethanol over. sometimes i wanted to speed up the process and turned up the
heat but it would steam and water would condensed into my alcohol so i would turn it down to a steady drip instead. out of 5 gallons of mash i got 2
pints of very strong ethanol and i'm sure its poisonous but its still ethanol and not methanol and burns clean until dry. my mash was made from corn
meal,sugar,yeast and distilled water and the ethanol smells like bacardi and boy i wish i had used all copper instead.
|
|
|
Saganism
Harmless
Posts: 18
Registered: 25-9-2012
Location: Ozark mountains
Member Is Offline
Mood: No Mood
|
|
I've got it running well now. Thanks for all the help
Just trying to figure some stuff out you know?
Aren't we all?
|
|
|
cal
Hazard to Self
Posts: 88
Registered: 7-2-2012
Member Is Offline
Mood: No Mood
|
|
Ethanol
I made a 220 volt hot plate for my ethanol distiller from a 8 inch electric stove burner and a 220 volt 4000 watt motor dimmer from ebay for 10.00.
Total cost of hotplate $40.00
I make all my ethanol from just sugar and yeast
( Fleischmann's ) for baking. I tried the special yeast for brewing and it produced less alcohol. I made a Boka http://wiki.homedistiller.org/Boka_Reflux_Still__How_To_Buid
and it works really well as I use about 2 to 3 liters at a time with my experiments.
|
|
|
IrC
International Hazard
Posts: 2710
Registered: 7-3-2005
Location: Eureka
Member Is Offline
Mood: Discovering
|
|
From your link : http://wiki.homedistiller.org/Boka_Reflux_Still__How_To_Buid
"Boka Reflux Still How To Buid
There is currently no text in this page. You can search for this page title in other pages, or search the related logs."
Did I miss something? Other than Buid should be build.
A quick site search yields : (works)
http://wiki.homedistiller.org/Boka_Reflux_Still_-_How_To_Bui...
And :
http://wiki.homedistiller.org/Boiler
http://wiki.homedistiller.org/Column_Connection_Options
[Edited on 10-10-2012 by IrC]
"Science is the belief in the ignorance of the experts" Richard Feynman
|
|
|
zed
International Hazard
Posts: 2283
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Well, I did onetime produce a water cooled distilling condenser entirely from Copper plumbing pipe. Used lead-free solder. Screwed it onto a
modified pressure cooker. Wasn't very expensive, and all of the parts were available at home depot.
Unlike a glass condenser, you can make it as big as you like, and yer Copper condenser will not shatter if torqued or dropped. Also, pressure cookers
come in friendly sizes, and sometimes can be purchased cheaply at garage sales. Even come in stainless steel. Very handy.
Once again, a caution; distilling ethanol from mash...may cause you legal problems in the U.S..
Uncle SAM wants his ethanol beverage tax.
|
|
|
hyfalcon
International Hazard
Posts: 1003
Registered: 29-3-2012
Member Is Offline
Mood: No Mood
|
|
Varies from state to state. Some states, Missouri for example, allow you to produce a certain quantity for your own consumption.
|
|
|
Arthur Dent
National Hazard
Posts: 553
Registered: 22-10-2010
Member Is Offline
Mood: entropic
|
|
Interesting thing about the copper reacting with the Ethanol vapors... I also have an all-glass distilling apparatus. Would a spiral of copper wire in
the claisen adapter be useful to obtain the same effect?
Robert
--- Art is making something out of nothing and selling it. - Frank Zappa ---
|
|
|
watson.fawkes
International Hazard
Posts: 2793
Registered: 16-8-2008
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Arthur Dent  | | I also have an all-glass distilling apparatus. Would a spiral of copper wire in the claisen adapter be useful to obtain the same effect?
|
Better yet, use a knit copper mesh (as can be found for scrubbing pots) as packing in a simple column.
|
|
|
Arthur Dent
National Hazard
Posts: 553
Registered: 22-10-2010
Member Is Offline
Mood: entropic
|
|
Thank you for your suggestion, but I must warn you that I have discovered much to my dismay that the "copper" scrubbing sponges that I find in my
neighborhood stores are actually coarse steel wool with a thin copper coating. That fubared one of my chemical reactions a while ago.
I don't know if it's just a local thing, but I thought I should mention it to make people aware that those shiny copper sponges may not be what they
seem.
But I'll try to make a makeshift copper wool ball out of multiconductor electrical wire and stuff it in the neck of the claisen adapter.
Robert
--- Art is making something out of nothing and selling it. - Frank Zappa ---
|
|
|
watson.fawkes
International Hazard
Posts: 2793
Registered: 16-8-2008
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Arthur Dent | I must warn you that I have discovered much to my dismay that the "copper" scrubbing sponges that I find in my neighborhood stores are actually coarse
steel wool with a thin copper coating. That fubared one of my chemical reactions a while ago.
|
I have head (but only heard) that they work adequately, though with not so long lifetimes, as column
packing. But there is a pure copper product available that's very much like it: structured copper mesh.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
