Chemgineer
Hazard to Others
Posts: 216
Registered: 25-5-2021
Member Is Offline
|
|
Reasonable choice of vacuum pump for distillation?
I have a few of those small diaphragm pumps which I use for filtrations, they work quite well but I was wondering if there is a better choice if I
want to run it for much longer for a vacuum distillation?
I've seen some of the liquid ring pumps available with vacuum chambers etc. perhaps one of those would be a good choice? I have some concerns about
damage to pump internals by any gasses or liquids that may carry over though.
|
|
|
Sulaiman
International Hazard
Posts: 3692
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
I see three general options ;
1) a water-powered aspirator.
Not too expensive, simple setup.
1.1) some members have implemented a closed-loop water recirculation pump system
2) a (relatively) cheap Chinese HVAC rotary vane pump, with frequent oil changes
2.1) take reasonable precautions such as gas-washing and anti-suckback traps,
but overall consider as 'semi-disposable' (a couple of years)
3) 'Western' (expensive) pump, accurate pressure measurement and control, cryogenic traps etc.
PS I have used cheap 12 Vdc pumps continuously for days - more reliable than expected.
[Edited on 12-9-2022 by Sulaiman]
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
teodor
National Hazard
Posts: 876
Registered: 28-6-2019
Location: Heerenveen
Member Is Offline
|
|
Do you need to control the temperature during distillation? The precision of temperature measurement is dependent on the precision of pressure
measurement. If you have no device which is sensitive enough to control the pressure in such a way that the corresponding temperature change will be
in the range of 1-2 degrees you are unable to collect fractions based on the temperature.
The higher vacuum made by electrical pumps compared to a water aspirator requires a more precious manometer (the same absolute change of pressure at a
high vacuum results in higher temperature change compared to a lower vacuum). So, for the purpose of vacuum distillation, I would choose the level of
vacuum pressure created by the pump based on the manometer sensitivity.
[Edited on 12-9-2022 by teodor]
|
|
|
Rainwater
National Hazard
Posts: 919
Registered: 22-12-2021
Member Is Offline
Mood: indisposition to activity
|
|
Assuming the apparatus is truly sealed and vacuum tight.
Once the vacuum is formed, will sealing the system prevent boiling point changes?
[Edited on 13-9-2022 by Rainwater]
"You can't do that" - challenge accepted
|
|
|
teodor
National Hazard
Posts: 876
Registered: 28-6-2019
Location: Heerenveen
Member Is Offline
|
|
Usually, to break the surface tension of liquid which prevents normal boiling under vacuum (the "bumping" effect), a fine stream of air or inert gas
is introduced through a capillary tube during vacuum distillation for the purpose of creating an additional pressure that breaks the surface tension
allowing vapors to escape the liquid.
This stream is tiny compared to a vacuum pump suction so it doesn't change the vacuum.
Without this stream of gas, the boiling point as determined by a thermometer will be different from a valid boiling point under a vacuum because there
are 2 forces that prevent the vapor to escape in this case: the pressure and the surface tension.
So, there is no way to break surface tension in a "truly sealed" apparatus so the boiling point will depend on surface tension.
|
|
|
Lionel Spanner
Hazard to Others
Posts: 168
Registered: 14-12-2021
Location: near Barnsley, UK
Member Is Offline
|
|
If it's a low-viscosity liquid with a low amount of suspended solids, vigorous stirring with a magnetic stirrer will break the surface as well.
However this is not generally achievable in a Claisen flask, as the base comes to a point.
|
|
|
Mateo_swe
National Hazard
Posts: 541
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
If you plan on doing some chemistry in the future i would suggest you start looking for a used, good quality diaphragm pump made for chemistry.
These have diaphragms that can withstand many chemicals and can be used for a long time, you can also replace the diaphragms if needed.
Start looking at trading sites for a working, used one with a low pricetag.
They are usually quite expensive even if used but sometimes a real cheap one pops up.
But they are quickly sold so you got to check trading sites often and have some patience, sooner or later a good deal comes up.
I purchased a used Vaccubrand diaphragm pump this way and its very good.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
