| Pages:
1
2
3 |
Yttrium2
Perpetual Question Machine
Posts: 1104
Registered: 7-2-2015
Member Is Offline
|
|
Lab Stands + Questions
How is this for a lab stand?
https://www.ebay.com/itm/Lab-Laboratory-Retort-Stands-Suppor...
It seems pretty inexpensive, I get tired of buying them...
Would this work to hold up a distillation apparatus?
I see online how certain distillation apparatus's are held up with only 1 stand, but 2 clamps -- would this work? If not, what else would I need to
setup a distillation apparatus?
I'm really wanting to save money
Also, what diameter ring goes with what separatory funnel?
Hmm...
[Edited on 11/25/2019 by Yttrium2]
|
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
15*8.5cm base and 30cm height, in my opinion it would be ok for microscale distillation, surely not for a 24/40 set and 500ml flasks.
how is $13 cheap?
buy 3 feet (1m) of 1cm (1/2") steel rod or tube, as a base you can use a wide wooden base, or a smaller steel/iron/concrete/lead base.
with 13 dollars you should be able to build at least 5 of those stands...
i built mines with a 1cm diameter steel rod 60cm high, and one has a wooden base, like 20cm*30cm and the other has a marble base 15*20 (found
discarded cuts a build site)
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
Yttrium2
Perpetual Question Machine
Posts: 1104
Registered: 7-2-2015
Member Is Offline
|
|
[Edited on 11/26/2019 by Yttrium2]
|
|
|
j_sum1
Administrator
Posts: 6323
Registered: 4-10-2014
Location: At home
Member Is Offline
Mood: Most of the ducks are in a row
|
|
I have always noted retort stands online are unreasonably expensive. It is true that you can easily make something yourself at a fraction of the
cost.
I built a rack made from nickel-plated drawer handles.
If I didn't have that, then I would be off to the industrial end of town with a sketch on a piece of paper and a sixpack in hand and asking someone
what they could knock up using scrap from the bin, a couple of tacks of a welding stick and a few minutes of their lunch break.
|
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Quote: Originally posted by Yttrium2  | How is this for a lab stand?
https://www.ebay.com/itm/Lab-Laboratory-Retort-Stands-Suppor...
It seems pretty inexpensive, I get tired of buying them...
Would this work to hold up a distillation apparatus?
I see online how certain distillation apparatus's are held up with only 1 stand, but 2 clamps -- would this work? If not, what else would I need to
setup a distillation apparatus?
I'm really wanting to save money
Also, what diameter ring goes with what separatory funnel?
Hmm...
[Edited on 11/25/2019 by Yttrium2] |
I literally just got one of these but it's so much smaller than I thought it would be and one of the clamps wouldn't lock tightly and slid up and down
the steel pole and no matter how tight I turn it it just won't lock to it.also the steel loop isn't big enough even for a 250ml SEP funnel to sit in.
Spend a few dollars more and get a bigger one with bigger clamps.
|
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
No it's not big enough to hold up a distillation setup unless you're talking microdistillation with 50ml flasks.
|
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
| Quote: Originally posted by j_sum1 | I have always noted retort stands online are unreasonably expensive. It is true that you can easily make something yourself at a fraction of the
cost.
I built a rack made from nickel-plated drawer handles.
If I didn't have that, then I would be off to the industrial end of town with a sketch on a piece of paper and a sixpack in hand and asking someone
what they could knock up using scrap from the bin, a couple of tacks of a welding stick and a few minutes of their lunch break.
|
Literally done that and got 4x 60cm high stands made up for $20. Only thing is i found out that mild steel rod bends when trying to support a 3 ltd
half full flask.so if doing this the rods need to be ss.the base plates can be mild steel though.
|
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
| Quote: Originally posted by draculic acid69 | | Quote: Originally posted by j_sum1 | I have always noted retort stands online are unreasonably expensive. It is true that you can easily make something yourself at a fraction of the
cost.
I built a rack made from nickel-plated drawer handles.
If I didn't have that, then I would be off to the industrial end of town with a sketch on a piece of paper and a sixpack in hand and asking someone
what they could knock up using scrap from the bin, a couple of tacks of a welding stick and a few minutes of their lunch break.
|
Literally done that and got 4x 60cm high stands made up for $20. Only thing is i found out that mild steel rod bends when trying to support a 3 ltd
half full flask.so if doing this the rods need to be ss.the base plates can be mild steel though. |
what's the diameter of your rods? mine are 1cm in diameter and made of mild steel, i could bend them maybe with my weight, surely not with a half full
3L flask
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
Yttrium2
Perpetual Question Machine
Posts: 1104
Registered: 7-2-2015
Member Is Offline
|
|
I saw Dr.Bob posted in a thread like this saying he uses the 2x8 (iirc) and drills a 7/16 hole for a 1/2 rod and presses it in somehow. I'm wondering
if it'd be best to have the hole go all the ways through the block? I'll probably do the same thing.
Walmart has 3/8 wooden dowels and other goodies in the arts and crafts diy section
Would a wooden dowels work for a rod or do I need it to be metal? I could glue the would into the hole but it might snap when I press it in. Also, I'm
not sure how I'm going to press it into the hole?
|
|
|
G-Coupled
Hazard to Others
Posts: 287
Registered: 9-3-2017
Member Is Offline
Mood: Slightly triturated
|
|
They look pretty cheap and nasty to my eyes - probably well worth springing up to around 2x the price to get something better, or get some threaded
metal rods and make some nice solid heavy bases to drill the mounting holes into. Then couple your DIY stands with some quality mounts and rings etc.
I particularly like the idea of using marble offcuts for the bases - nice and heavy, looks good and will take spills etc. like a champ. 
 
[Edited on 26-11-2019 by G-Coupled]
|
|
|
Yttrium2
Perpetual Question Machine
Posts: 1104
Registered: 7-2-2015
Member Is Offline
|
|
I'm not sure how the rod would connect to the marble, I have very limited construction skills. -- would I want to take a carpentry class to learn
about screws, tabs, and DIY or some sort of construction gig?
|
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
| Quote: Originally posted by Ubya | | Quote: Originally posted by draculic acid69 | | Quote: Originally posted by j_sum1 | I have always noted retort stands online are unreasonably expensive. It is true that you can easily make something yourself at a fraction of the
cost.
I built a rack made from nickel-plated drawer handles.
If I didn't have that, then I would be off to the industrial end of town with a sketch on a piece of paper and a sixpack in hand and asking someone
what they could knock up using scrap from the bin, a couple of tacks of a welding stick and a few minutes of their lunch break.
|
Literally done that and got 4x 60cm high stands made up for $20. Only thing is i found out that mild steel rod bends when trying to support a 3 ltd
half full flask.so if doing this the rods need to be ss.the base plates can be mild steel though. |
what's the diameter of your rods? mine are 1cm in diameter and made of mild steel, i could bend them maybe with my weight, surely not with a half full
3L flask |
Yeah 1cm. They were not the threaded stuff you get from the hardware store.just normal smooth 1cm 60-90cm tall mild steel rod.they just have too much
flex in them
whereas ss won't flex at all.if you keep the flask size under a litre I suppose it wouldn't bend too much if kept low as long as your not distilling
mercury.
[Edited on 27-11-2019 by draculic acid69]
|
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
| Quote: Originally posted by Yttrium2 | | I'm not sure how the rod would connect to the marble, I have very limited construction skills. -- would I want to take a carpentry class to learn
about screws, tabs, and DIY or some sort of construction gig? |
That would be overkill.just watch a few you tube videos on the subject.
But the idea of using marble is a nice idea.
[Edited on 27-11-2019 by draculic acid69]
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
I made my rack out of type L copper and black iron flanges.
|
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
| Quote: Originally posted by Yttrium2 | | I'm not sure how the rod would connect to the marble, I have very limited construction skills. -- would I want to take a carpentry class to learn
about screws, tabs, and DIY or some sort of construction gig? |
i only have a hand drill, so i drilled a 9mm hole ( a drill press does the job fast and easy) in the marble slab, drilling by hand the hole got a bit
wider than 9mm but still less than a cm in a few places. a light touch with a file and the rod is press fitted in the hole. i drilled an oblique hole
though... so my stand has a 10° inclination to one side
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
Yttrium2
Perpetual Question Machine
Posts: 1104
Registered: 7-2-2015
Member Is Offline
|
|
I'll probably go with one of these, I wasn't sure what they were called
Also am posting this in case no one else knows of these flange things
[Edited on 11/27/2019 by Yttrium2]
Now, is there any additional special hardware one needs to mount these besides some screws and the poles?
Is there a screw recommendation ?
I may go with what Dr.Bob said in another thread, to press the 1cm rod into a 7/16 hole-- this may be the cheaper route, actually I'll probably do
this.
Any suggestions for what rod is the cheapest/ where can I acquire one? Links?
And how do I still a hole that is centered???
[Edited on 11/27/2019 by Yttrium2]
[Edited on 11/27/2019 by Yttrium2]
[Edited on 11/27/2019 by Yttrium2]
|
|
|
unionised
International Hazard
Posts: 5126
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Placing a RB flask on one of those metal rings and then heating it with a bunsen flame is a great way to break glassware.
|
|
|
morganbw
National Hazard
Posts: 561
Registered: 23-11-2014
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by unionised | | Placing a RB flask on one of those metal rings and then heating it with a bunsen flame is a great way to break glassware. |
Much truth in this statement.
|
|
|
Yttrium2
Perpetual Question Machine
Posts: 1104
Registered: 7-2-2015
Member Is Offline
|
|
Hey no one asked that, what about my questions?
|
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
in a modern country every hardware store has steel rods, they are not expensive at all.
to drill a straight hole you need a drill press, or a very firm hand, two things i don't have
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
G-Coupled
Hazard to Others
Posts: 287
Registered: 9-3-2017
Member Is Offline
Mood: Slightly triturated
|
|
I know that they're different things, but I can't help thinking that anyone who's of a mind to (attempt to) perform semi-serious home chemistry
shouldn't have much of a problem figuring enough simple DIY to make a ghetto but functional lab stand out of bits of scrap.
In suppose let's just thank god we're not in the Before Times of Amateur (& Professional) Natural Science where you had to be half decent at
making and hacking your own glassware if you wanted to actually do anything.
[Edited on 27-11-2019 by G-Coupled]
[Edited on 27-11-2019 by G-Coupled]
|
|
|
Abromination
Hazard to Others
Posts: 432
Registered: 10-7-2018
Location: Alaska
Member Is Offline
Mood: 1,4 tar
|
|
Doesn’t look like something I would ever trust with my glass. Spend a couple extra dollars to buy a decent stands.
This is a solid one that I use for everything.
https://www.amazon.com/American-Educational-7-G15-Support-Re...
List of materials made by ScienceMadness.org users:
https://docs.google.com/spreadsheets/d/1nmJ8uq-h4IkXPxD5svnT...
--------------------------------
Elements Collected: H, Li, B, C, N, O, Mg, Al, Si, P, S, Fe, Ni, Cu, Zn, Ag, I, Au, Pb, Bi, Am
Last Acquired: B
Next: Na
-------------- |
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
| Quote: Originally posted by Yttrium2 | I'll probably go with one of these, I wasn't sure what they were called
Also am posting this in case no one else knows of these flange things
[Edited on 11/27/2019 by Yttrium2]
Now, is there any additional special hardware one needs to mount these besides some screws and the poles?
Is there a screw recommendation ?
I may go with what Dr.Bob said in another thread, to press the 1cm rod into a 7/16 hole-- this may be the cheaper route, actually I'll probably do
this.
Any suggestions for what rod is the cheapest/ where can I acquire one? Links?
And how do I still a hole that is centered???
[Edited on 11/27/2019 by Yttrium2]
[Edited on 11/27/2019 by Yttrium2]
[Edited on 11/27/2019 by Yttrium2] |
I think It's a thing that is used on boats or display stands.i know a boating supply would have them in 316ss and I've seen some in hardware stores
too.wherever chrome plated mild steel tube is available.ahhhhhh wait a sec curtain rods.there curtain rod mounts.no wait there for the rods you hang
your clothes on in the cupboard.i use a floordrobe despite having an empty wardrobe so i forget what you call them .on boats there used for mounting
the ss
railings around the boat.
[Edited on 28-11-2019 by draculic acid69]
|
|
|
G-Coupled
Hazard to Others
Posts: 287
Registered: 9-3-2017
Member Is Offline
Mood: Slightly triturated
|
|
18 bucks isn't a bad price to pay to protect your precious glassware, reagents and health from some avoidable mishaps if you can't be bothered to DIY
one IMO. Especially if it's easy to add extra weight to the base with them.
[Edited on 28-11-2019 by G-Coupled]
[Edited on 28-11-2019 by G-Coupled]
[Edited on 28-11-2019 by G-Coupled]
|
|
|
Yttrium2
Perpetual Question Machine
Posts: 1104
Registered: 7-2-2015
Member Is Offline
|
|
Could I use 1 stand to hold up a distillation apparatus?
|
|
|
| Pages:
1
2
3 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
