soma
Hazard to Others
Posts: 297
Registered: 31-7-2010
Member Is Offline
Mood: No Mood
|
|
drying ether
Having done some searching I haven't found anything about drying (ethyl) ether by distilling from concentrated sulfuric acid.
Would there be a problem doing this?
If not, I was wondering how much sulfuric would be used? Also, would it remove peroxides?
Thanks.
|
|
|
entropy51
Gone, but not forgotten
Posts: 1612
Registered: 30-5-2009
Member Is Offline
Mood: Fissile
|
|
Soma, there are multiple threads on drying ether. The subject has been beaten practically to death and many good methods have been suggested.
Sulfuric is not one of them as best I can remember.
Check out the existing threads if you haven't already.
|
|
|
soma
Hazard to Others
Posts: 297
Registered: 31-7-2010
Member Is Offline
Mood: No Mood
|
|
I have checked out the threads and sulfuric wasn't a method I saw mentioned - but I don't know why not - it would seem to be a simple method. I was
wondering if it would also remove peroxides.
|
|
|
smuv
National Hazard
Posts: 842
Registered: 2-5-2007
Member Is Offline
Mood: Jingoistic
|
|
Sulfuric acid cannot be used for drying ether because it reacts with it.
Sulfuric acid, not only has a high enough pKa to protonate ether, making the etherate (HCl can do this too) and the bisulfate ion, but it is also a
strong enough nucleophile to attack the etherate causing cleavage to ethyl hydrogen sulfate and ethanol (-Cl is not a strong enough nucleophile to do
this under normal conditions). The ethyl hydrogen sulfate and ethanol can go on to form various products in the presence of H2SO4 (water being one of
them).
This is why ether is stable to some strong acids which are poor nucleophiles (actually HCl is the only one that comes to mind) but not stable to
others which are good nucleophiles.
If you were to take a mixture of ether and H2SO4 and distill it, I would expect the formation of a lot of ethylene with very little ether distilling
over, whatever did carry over would probably contain quite some ethanol and maybe water. Also, H2SO4 cannot simply be shaken with either and then
separated from it in a sep funnel, as Ether is miscible with conc. H2SO4 (due to formation of the etherate).
"Titanium tetrachloride…You sly temptress." --Walter Bishop
|
|
|
transformer
Harmless
Posts: 45
Registered: 30-6-2005
Member Is Offline
Mood: No Mood
|
|
Passibg the ether to a column with alumina will removed the peroxides and if your ether is not soaking wet mol sieves are a most excellent way to dry
it.
|
|
|
rrkss
Hazard to Others
Posts: 193
Registered: 18-12-2009
Member Is Offline
Mood: No Mood
|
|
I've dried ether to grignard grade by first treating it with acidified FeSO4 to destroy peroxides and then, doing an initial dry on anhydrous CaCl2.
I distill it from the CaCl2 and dry it over either type 3A or 4A molecular sieves overnight and distill from that using oven dried glassware.
I've run grignards with ether using this method multiple times with no problem.
|
|
|
Ozone
International Hazard
Posts: 1269
Registered: 28-7-2005
Location: Good Olde USA
Member Is Offline
Mood: Integrated
|
|
Distill from continuous reflux over Na-ketyl (benzophenone). Good for THF, too.
-Anyone who never made a mistake never tried anything new.
--Albert Einstein
|
|
|
rrkss
Hazard to Others
Posts: 193
Registered: 18-12-2009
Member Is Offline
Mood: No Mood
|
|
I think if he is asking this he won't have the equipment to setup an O2/Moisture free still to do this though that is standard procedure in my
university's graduate labs.
|
|
|
Methyl.Magic
Hazard to Others
Posts: 139
Registered: 14-5-2007
Member Is Offline
Mood: No Mood
|
|
Et2O can be checked by adding a KI crystal and few AcOH drops. If the Et2O is still colorless it's peroxide-free.
Wet Et2O can be dried over Na2SO4 (cheap),then distilled from CaO to get anhydrous Et2O. Then conserv it over molecular sieve. Works well for Grignard
, BuLi and LiAlH4 but it can still fizzes with this latter when you add the first portion.
|
|
|
Melgar
Anti-Spam Agent
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
If the goal is drying ether for a Grignard reaction, best to use sodium hydroxide as your drying agent. If you're getting it from starter fluid,
which I'm assuming you are because that's the easiest source, then not only do you have to remove water, but CO2 as well. CO2 is usually used as the
propellant in starter fluid, so this is quite important. Calcium oxide should work theoretically, but I think sodium hydroxide is easier to get.
Drying ether for about a week using sodium hydroxide will make it suitable for a Grignard reaction.
|
|
|
mario840
Hazard to Others
Posts: 229
Registered: 20-1-2010
Member Is Offline
Mood: No Mood
|
|
this is simple .... you take 1 l ether and add 120 CaCl2 and shake , leave for couple days , shake every day , filter and add thin sodium metal , if
evolution of hydrogen will stop you got anhydrous ether good for grignards reaction but you may destill if above sodium and protect with drying tube
CaCl2 ...that's all
|
|
|
Oxydro
Hazard to Others
Posts: 152
Registered: 24-5-2004
Location: NS, Canada
Member Is Offline
Mood: distracted
|
|
Mario840, to consider anything with metallic sodium 'simple' disregards the resources (or rather, lack of) that most of us have. Sodium is definitely
not OTC, courtesy of both litigation and Birch.
"Our interest's on the dangerous side of things" -- Browning
|
|
|
mario840
Hazard to Others
Posts: 229
Registered: 20-1-2010
Member Is Offline
Mood: No Mood
|
|
sorry for me is OTC ..is cheap like a beer and on this site is illustrated how to make sodium metal ... plutonium-239 is OTC
|
|
|
mario840
Hazard to Others
Posts: 229
Registered: 20-1-2010
Member Is Offline
Mood: No Mood
|
|
it should be: is NOT OTC  for plutonium
|
|
|
soma
Hazard to Others
Posts: 297
Registered: 31-7-2010
Member Is Offline
Mood: No Mood
|
|
ether peroxides
I'm trying to understand the mechanism of peroxide formation with ether. I assume that the ethyl groups donate electrons and make the oxygen basic?
Therefore, acids might prevent peroxide formation?
Thanks to all who replied to my other question about ether drying.
|
|
|
Lambda-Eyde
National Hazard
Posts: 860
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
http://commons.wikimedia.org/wiki/File:Ether_peroxide_format...
|
|
|
Nicodem
|
Threads Merged
8-8-2010 at 13:06 |
chemrox
International Hazard
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
Contrary to common undergraduate beliefs fairly wet ether will still work in the Grignard. The main precaution I've found important is making a good
blanket of ether vapor over the Mg turnings before starting the reaction. In other words I start the reflux and then run in the first, more
concentrated aliquot of halocarbon. Br-C's seem the easiest. Any oxide on the Mg is problem. If the turnings have got any grey edges use them for
something else like fireworks or making MgCl2.
"When you let the dumbasses vote you end up with populism followed by autocracy and getting back is a bitch." Plato (sort of)
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
