Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: Removing alkanes from an amine
wg48temp9
National Hazard
****




Posts: 784
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline


[*] posted on 4-1-2019 at 07:30
Removing alkanes from an amine



How can I replace the two alkans with hydrogen on the amine (the right hand N) in this azo dye?

I searched but found no method, I guess its probably difficult or requires exotic reagents. I do not want to change any other groups in the dye.

Disperse_Red_50.gif - 4kB

Sorry I don't why the system keeps putting the extra images in the post





[Edited on 4-1-2019 by wg48temp9]

Disperse_Red_50.gif - 4kB Disperse_Red_50.gif - 4kB

[Edited on 4-1-2019 by wg48temp9]




I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
View user's profile View All Posts By User
draculic acid69
International Hazard
*****




Posts: 1371
Registered: 2-8-2018
Member Is Offline


[*] posted on 4-1-2019 at 18:59


N, demethylation removes methyl groups but I don't know if it extends to other alkyl groups like deethylation or depropylation but it might be a good place to start.the only things I've heard of people wantinh to N,demethylate is opiates.O, demethylation is much more common.anyway polonovski demethylation,opiate chemistry and N, demethylation are three places I would suggest that you have a good look at.i think it involves oxidizing the amine with h2o2 to form an N,oxide and ferrous sulphate to remove the alkyl. I always wondered if this also works on ethyl and propyl groups.good luck.
View user's profile View All Posts By User
Sigmatropic
Hazard to Others
***




Posts: 307
Registered: 29-1-2017
Member Is Offline

Mood: No Mood

[*] posted on 4-1-2019 at 19:56


That cyanoethyl group looks like it can be cleaved back to acrylonitrile, as is the case when it is used as a protecting group on phosphates. (I will look up some conditions for cyanoethyl anilines tomorrow).
And the stereotypical reaction to demethylate amines is the von braun reaction, or it's more modern modification using some alkyl chloroformate (methyl, ethyl or isopropyl).
https://en.m.wikipedia.org/wiki/Von_Braun_reaction
View user's profile View All Posts By User
draculic acid69
International Hazard
*****




Posts: 1371
Registered: 2-8-2018
Member Is Offline


[*] posted on 4-1-2019 at 20:32


Does the Von braun alkyl cloroformate rxn extend to ethyl,propyl,butyl groups?

[Edited on 5-1-2019 by draculic acid69]
View user's profile View All Posts By User
wg48temp9
National Hazard
****




Posts: 784
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline


[*] posted on 5-1-2019 at 03:25


Thanks for the suggestions guys.

i looked at the N-oxide method again. I assume as my dye is not water soluble I need an organic peroxide but I suspect almost any organic peroxide will do. Then I remembered OPs are available OTC as catalysts for resins. They are expensive and are usually diluted (not in water) but just affordable for me as I only need a few tens of grams.

I also want to try hydrolyzing the nitrile.

Ok its probably less than 50% MEKP: 130ml £2.50 at https://www.mbfg.co.uk/butanox-m50-130ml.html?gclid=EAIaIQob...





[Edited on 5-1-2019 by wg48temp9]




I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
View user's profile View All Posts By User
zed
International Hazard
*****




Posts: 2283
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline

Mood: Semi-repentant Sith Lord

[*] posted on 5-1-2019 at 15:57


Find another starting material.

Probably easier to build your target material from scratch, than it is to modify that tertiary amine.



View user's profile View All Posts By User

  Go To Top