| Pages:
1
2
3
4 |
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
It pulls a vacuum but is a bit loud, and caulking a pipe into the bucket doesn't seem to be a very durable solution. I'm planning on fitting an
airtight lid with hosebarb to it so it can vent gases easily, and I'm considering detaching the pump and using an unmodified bucket. I'm pretty sure
I'll have to prime the pump if I do that, though.
I have a vacuum pump, but I can't use it to remove solvents under vacuum, and it's vulnerable to attack by acids, halogens, and so forth.
|
|
|
Geocachmaster
Hazard to Others
Posts: 146
Registered: 5-3-2016
Location: Maine, USA
Member Is Offline
Mood: Corroded, just like my spatulas
|
|
I just spent $600 on stuff for the lab. Various chemicals, new glassware (most notably a Dean-Stark trap), and something that I've been yearning for
for a long time...
A Chemglass PTFE diaphragm vacuum pump!!!  
It's a used one from eBay and is this model. It's supposed to arrive next week but I was so excited I had to post something now.
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
Nice. Those diaphragm pumps definitely have their uses.
|
|
|
Geocachmaster
Hazard to Others
Posts: 146
Registered: 5-3-2016
Location: Maine, USA
Member Is Offline
Mood: Corroded, just like my spatulas
|
|
Here it is!!!
https://www.youtube.com/watch?v=wbVXF9Wr77k
|
|
|
Vosoryx
Hazard to Others
Posts: 282
Registered: 18-6-2017
Location: British Columbia, Canada
Member Is Offline
Mood: Serial Apple Enjoyer
|
|
So I saw this ad on craigslist, (if you don't know what that is, it's a place where everyday people can sell and buy things. Less exclusive than
Ebay.) for a 6000ml erlenmeyer flask, two allihn condensers, and a 500ml grad. cylinder. It was a great deal, so I go to pick it up, and the seller
decides to add in a handful of test tubes with rubber stops and three quartz glass tubes that he had laying around. And he decides to give it all to
me for free.
I have no idea what i'm going to use it all for, but I have it!
The glassware, excluding the quartz glass, is all Pyrex. None of it is ground glass, which is a bit unfortunate, but I'm sure I'll get some use out of
this free glassware!
Probably not the right thread, but I'm very excited so I had to share it. 
I should have put a scale there, If you don't already know the size of some of the stuff it could look smaller than it is. The Erlenmeyer is 6 liter,
the grad cylinder is 500ml, and I think the condensers are 400mm.
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
Well scored Ascorbic acid and my NaNO2 finally arrived! getting so close to azids and the like I can "Taste" it!
Next will be glass wear! More of rather.
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
I got a [very inexpensive] new in box Glas-Col 500 mL heating mantle, with power cord! No longer will I have to mess around with salt baths and oil
baths at a 500 mL scale.
Another big plus is that I won't have to endanger myself with this abomination every time I want to use my other heating mantle.
[Edited on 28-11-2017 by JJay]
|
|
|
Vosoryx
Hazard to Others
Posts: 282
Registered: 18-6-2017
Location: British Columbia, Canada
Member Is Offline
Mood: Serial Apple Enjoyer
|
|
Nice find!
I have a glas-col 500 mL
I got it used off of ebay very inexpensively, and was actually concerned it might contain asbestos. I called them up, it doesn't.
Sure beats a sand bath.
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
I got a PID controller with a big relay. My plan is to wire it up with an oven dimmer and use it to control my various electric heating apparatuses.
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
I got an infrared temperature sensor. I really ought to pick up a heat gun at some point....
|
|
|
CharlieA
National Hazard
Posts: 646
Registered: 11-8-2015
Location: Missouri, USA
Member Is Offline
Mood: No Mood
|
|
My wonderful EE brother-in-law set up a PID for me. Now I use it to control a cheap toaster-oven. This set-up makes a great drying oven.
[Edited on 12-21-2017 by CharlieA]
|
|
|
CharlieA
National Hazard
Posts: 646
Registered: 11-8-2015
Location: Missouri, USA
Member Is Offline
Mood: No Mood
|
|
Tomorrow my new microscope arrives. This will be my first real microscope. The last one was basically a toy that I had ~65 years ago. I haven't been
using up my chemistry budget lately, so this is a Christmas gift, from me to me, with love. I've never studied biology/microbiology yet, but I guess
it is never too late to (try) to learn.
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
  
|
|
|
MrHomeScientist
International Hazard
Posts: 1806
Registered: 24-10-2010
Location: Flerovium
Member Is Offline
Mood: No Mood
|
|
I have exactly the same regulator/flowmeter for my Ar tank. Works great! If all goes well, I'll be using it this weekend in combination with my new
propane furnace (this one) Appears to be good quality but we'll see how the test run goes.
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
Nice furnace. I wasn't sure if I had the regulator screwed on all the way, but the flare fitting doesn't want to go any tighter even with a fairly
large crescent wrench, and I don't want to strip off any threads.
I am going to try playing with some organometallics soon. I am probably going to start with something easy like synthesizing t-butanol from acetone
and methylmagnesium iodide.
[Edited on 12-1-2018 by JJay]
|
|
|
NEMO-Chemistry
International Hazard
Posts: 1559
Registered: 29-5-2016
Location: UK
Member Is Offline
Mood: No Mood
|
|
I dont normally post in this, not even my prized satorius balance!! But i figured i would share this enay score with you....
Now you all know how i like my real books, take a wild guess what i won this lot for in the auction with P&P?
22 books all together. I will post pics of some the highlights for me.
Three of them i already have, so if anyone is interested shout me. One i think is fairly hard to get and costs a fortune normally.
its the last three i have duplicates of now
I think i am now well over 200 hardback books on chemistry and biology
![20180113_030225[1].png - 849kB](https://www.sciencemadness.org/whisper/files.php?pid=503644&aid=64043) ![20180113_030308[1].png - 1021kB](https://www.sciencemadness.org/whisper/files.php?pid=503644&aid=64045) ![20180113_030354[1].png - 1MB](https://www.sciencemadness.org/whisper/files.php?pid=503644&aid=64047) ![20180113_030511[1].png - 1MB](https://www.sciencemadness.org/whisper/files.php?pid=503644&aid=64049) ![20180113_030706[1].png - 1018kB](https://www.sciencemadness.org/whisper/files.php?pid=503644&aid=64051) ![20180113_030531[1].png - 838kB](https://www.sciencemadness.org/whisper/files.php?pid=503644&aid=64053) ![20180113_030554[1].png - 990kB](https://www.sciencemadness.org/whisper/files.php?pid=503644&aid=64055)
[Edited on 13-1-2018 by NEMO-Chemistry]
|
|
|
Geocachmaster
Hazard to Others
Posts: 146
Registered: 5-3-2016
Location: Maine, USA
Member Is Offline
Mood: Corroded, just like my spatulas
|
|
I just got two reaction vessels with lids! Both are 2 liters, one is glass and the other is stainless steel. From the same person, I got a 2 liter
glas-col heating mantle and five new clamps.
$35 for the lot!
 
 
 
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
Sweet deal. I wish I could find something like that.
|
|
|
weilawei
Hazard to Others
Posts: 130
Registered: 3-12-2017
Member Is Offline
Mood: No Mood
|
|
Scored a Mel-Temp II for $39 plus $17 shipping. I don't often bid on eBay auctions, but I threw in a bid as a hail mary, and now I own a proper
melting point apparatus. Previousluly, I was using a big steel plate I'd drilled a hole in for a thermocouple and a dent for a sample well.
The bulb is burnt out, but these cost like 50 cents to replace. It heats beautifully, and my old mercury thermometer fits perfectly.
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
well it arrived! some fun new supplies I been waiting for!
and some glass wear
  
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
rawr
Yes, my new ball mill was 300 munnies. Now to figure out some sort of media... I wonder if buckshot works.
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
j_sum1 suggested this device for extruding sodium wire a while back, so I figured I'd pick one up. I'm looking forward to finding out how well it
works.
|
|
|
Sulaiman
International Hazard
Posts: 3695
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Online
|
|
They work well for making sodium wire - very shiny on exit.
Cleaning after use can be 'interesting' 
(dis-assemble and throw in a big bowl of water is my safest method so far)
(overall, I find it is easier to just use small pieces of sodium)
(oil the threads before use or they may get stuck)
P.S. for experiments such as 'transparent sodium' or sodium 'coulombic explosion' the extruder is really useful
for making sodium wire which can be extruded then cut off to a desired length,
giving approximately the same sample size each time.
Like a pipette for metal
(measuring small sodium samples is otherwise non-trivial)
..........................................
To save another comment box, my answer to the question below is
'I don't keep isopropanol in stock so I've not tried'
but it does sound more expensive and less fun.
[Edited on 18-8-2018 by Sulaiman]
|
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Maybe quench with isopropanol would be safer?
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
I got a steel five-gallon bucket with a locking lid: https://www.ebay.com/itm/Steel-Pail-Black-Cap-5-Gal-With-Lin...
I'm going to try to build a heating mantle for it with heat tape and fiberglass, but I'll probably remove the paint first.
|
|
|
| Pages:
1
2
3
4 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
