Pages:
1
2
3 |
underground
National Hazard
Posts: 704
Registered: 10-10-2013
Location: Europe
Member Is Offline
|
|
Hey Buddy, i just saw your message.... Check this out, it may help you
https://www.youtube.com/watch?v=vTrBWW_fqe8
|
|
Hey Buddy
Hazard to Others
Posts: 441
Registered: 3-11-2020
Location: Bushwhacker Country
Member Is Offline
|
|
I have seen this but that is what is confusing. I am using the same source of synthesis that he is using in the video but I have done something wrong
which I can't seem to identify yet. The main striking difference is that in the ANQN video he is seeing a deepening of color to clear orange on
standing after neutralization with HCl. Where as in my case, I am seeing clear yellow prior to neutralization then there is opaque precipitate that
comes out of solution when adjusting pH. It never gets clear orange. I have achieved an orange solution once, but it was in an experiment with no
neutralization at high pH. In that case nothing precipitated out of solution for 2 days of standing. I may attempt to copy the source procedure again
and take some pictues. Maybe it will happen once again and i can capture whats going on.
[Edited on 10-4-2023 by Hey Buddy]
I have reviewed the video and writeup based on video. There are some errors. Unfortunately that write up (if actually what was used in video) is a bit
short on hydrazine ratio to NQ so it wouldnt be capable of a complete hydrazinolysis. I will instead try the last work up I used but will increase
ratio of hydrazine.
[Edited on 11-4-2023 by Hey Buddy]
|
|
Hey Buddy
Hazard to Others
Posts: 441
Registered: 3-11-2020
Location: Bushwhacker Country
Member Is Offline
|
|
Problem Solved
Back in lab on this. I tried the reaction with a little greater excess of hydrazine and used water instead of alcohol. Easily achieved dark orange
color. Precipitation of fine material already began after adjusting pH to 7. I believe alcohol somehow prevents the correct reaction and kicks out
nitroguanidine. H2O allows it to proceed correctly and smoothly. --Im testing out some ANQ salts as primary explosives. First check is simple
cupramine ANQ perchlorate.
[Edited on 11-4-2023 by Hey Buddy]
|
|
Raid
Hazard to Everyone
Posts: 203
Registered: 14-11-2022
Location: N/A
Member Is Offline
|
|
Does anyone know of a place to get cheap hydrazine hydrate?
I've had a hard time freebasing the sulfate.
|
|
specialactivitieSK
Hazard to Self
Posts: 94
Registered: 21-10-2014
Member Is Offline
Mood: No Mood
|
|
https://youtu.be/QK_zsRBlkt0
|
|
specialactivitieSK
Hazard to Self
Posts: 94
Registered: 21-10-2014
Member Is Offline
Mood: No Mood
|
|
Is ANGN enough sensitive as plastic explosive (pib+oil)?
|
|
Hey Buddy
Hazard to Others
Posts: 441
Registered: 3-11-2020
Location: Bushwhacker Country
Member Is Offline
|
|
ANQN is impact sensitive to 10J and 120N on friction according to Klapotke. That sensitivity, 10 J/120 N for ANQN, is comparable to RDX @ 7.5 J/120 N.
From what I see, ANQN may generally be more insensitive than a 10 J equivalent. It is definitely mechanically insensitive enough for a Plastic Bonded
eXplosive. My immediate concern, without any testing, is possible flame reactivity. If the explosive is bound it can change behavior and ANQN
deflagrates in flame contact more vigorously than rdx, in my opinion.
[Edited on 29-4-2023 by Hey Buddy]
|
|
Pages:
1
2
3 |