Pages:
1
2 |
SaccharinSlayer157
Harmless
Posts: 24
Registered: 1-10-2020
Location: Near Cou?
Member Is Offline
Mood: Resisting the urge to build a ketene lamp
|
|
Confusion on SO3 Synthesis
Just a quick question about the importance of cations in certain reactions, hopefully I'm posting this in the right place...
So I recently attempted the SO3 outlined in this video. I cleaned my glassware really well to avoid the contamination he encountered, but I used sodium persulfate instead of the potassium
salt because I found it for cheaper online. After running it, however, I found that I couldn't collect any product at all. Even after repeating it
with different amounts of sulfuric acid and strong prolonged heating no SO3 ever came over for me to collect. In general I've always thought that
alkali metal cations for salts can be pretty interchangeable for most reactions, but I'm wondering if this reaction might be an exception where sodium
persulfate doesn't decompose nearly as readily as its potassium counterpart for some reason. I know I definitely formed some SO3 because I
saw its characteristic fumes once the reaction flask was opened to the air, but it dissipated very quickly. I just want to know if this could be the
reason for my failure so I need to obtain some of the potassium salt or if I'm overlooking something in my setup instead that I need to investigate
further. I'm working with pretty small amounts and it's expensive and difficult to order any chemicals at the moment so I'd like to rule this out as a
possibility before I devote any more time and money to it .
|
|
metalresearcher
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 737
Registered: 7-9-2010
Member Is Offline
Mood: Reactive
|
|
The largest online chemistry textbook tells that K2S2O8 decomposes below 100C while Na2S2O8 does not, it melts 'normally' at 180 C.
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7990
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
@metalresearcher: That does not need to make a big difference.
Persulfate decomposes in two stages. The first stage is loss of oxygen:
2 K2S2O8 ---heat---> 2 K2S2O7 + O2 (apparently 100 C is sufficient for this reaction to occur)
The same also happens for the sodium salt, but at a higher temperature.
The second stage is loss of SO3:
K2S2O7 ---->lots of heat---> K2SO4 + SO3
I do not know what heat is needed to get SO3, but it must be considerable. I can imagine that for Na2S2O7 the temperature, needed for making SO3 is
higher than for K2S2O7, but I am quite sure that for K2S2O7 also quite a high temperature is needed. Do not expect this reaction to occur easily.
|
|
Admagistr
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 350
Registered: 4-11-2021
Location: Central Europe
Member Is Offline
Mood: The dreaming alchemist
|
|
Quote: Originally posted by woelen ![](images/xpblue/lastpost.gif) | @metalresearcher: That does not need to make a big difference.
Persulfate decomposes in two stages. The first stage is loss of oxygen:
2 K2S2O8 ---heat---> 2 K2S2O7 + O2 (apparently 100 C is sufficient for this reaction to occur)
The same also happens for the sodium salt, but at a higher temperature.
The second stage is loss of SO3:
K2S2O7 ---->lots of heat---> K2SO4 + SO3
I do not know what heat is needed to get SO3, but it must be considerable. I can imagine that for Na2S2O7 the temperature, needed for making SO3 is
higher than for K2S2O7, but I am quite sure that for K2S2O7 also quite a high temperature is needed. Do not expect this reaction to occur easily.
|
Yes Wilco,but SO3 at temperatures above 500C and at 1000C completely transform to SO2 and O2.I melted KAl(SO4)2 at 1000C for 6 hours and observed
this.
|
|
SaccharinSlayer157
Harmless
Posts: 24
Registered: 1-10-2020
Location: Near Cou?
Member Is Offline
Mood: Resisting the urge to build a ketene lamp
|
|
I guess I'll just have to try again with the potassium salt and see whether that or my setup was the issue. Thanks for the insight, I'll post an
update once I've run it again!
|
|
teodor
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 874
Registered: 28-6-2019
Location: Heerenveen
Member Is Offline
|
|
SaccharinSlayer157, trying to produce SO3 from a small amount of salt make sure everything is perfectly dry.
1g of Na2S2O7 gives a max of 0.3g of SO3 (and you never can get so a high yield) but 0.07 g of H2O is enough to spoil the result because it will bind
with SO3 to form H2SO4.
Also, wet SO3 has a tendency to polymerization, so it could be hard to distill it in this form. If I would make such an experiment I would mix the
salt with a tiny amount of P2O5 or red P to bind all free water (but I never did this experiment, so accept that recommendation with a grain of salt).
Other aggressive drying agents should also work. I think they also will depress the reaction temperature.
[Edited on 14-11-2022 by teodor]
|
|
SaccharinSlayer157
Harmless
Posts: 24
Registered: 1-10-2020
Location: Near Cou?
Member Is Offline
Mood: Resisting the urge to build a ketene lamp
|
|
So I just finished my second much more careful run, cleaned and dried my glassware and the salt meticulously and even redistilled my sulfuric acid
just in case. I got the mix molten and up to at least 500-600C for over an hour and still got nothing, barely even any oxygen evolution. It’s
looking to me like the sodium salt is just too stubborn to decompose appreciably, so I’ve ordered some potassium persulfate and will try with that
once it arrives.
|
|
Texium
|
Thread Moved 3-12-2022 at 08:17 |
clearly_not_atara
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2725
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
I've often wondered if there was a way to directly acidify pyrosulfate. Unfortunately, disulfuric acid is extremely strong (comparable to
chlorosulfonic acid, pKa < -10) for the first deprotonation. I haven't found any reliable data for the second deprotonation. The only candidate I
can think of is phosphotungstic acid H3PW12O40, but this would require a lot of tungsten, and solvent selection is non-obvious. HBr and HI are strong
enough, but would be oxidized; HClO4 is strong enough, but could explode. HCl is significantly weaker than sulfuric acid.
The order of strength of extremely strong acids is solvent-dependent, so "aqueous" pKa values are not necessarily reliable; FSO3H is stronger than
HClO4 in sulfuric acid but weaker in acetic acid.
I strongly suspect that KHS2O7 decomposes more readily than K2S2O7. So one protonation should be enough.
|
|
MaeBorowski
Harmless
Posts: 12
Registered: 8-3-2021
Location: six feet under
Member Is Offline
|
|
HCl is stronger than H2SO4 but here we are. Disulfuric acid isn't stable at elevated temperature and will decompose. There is very common method which
describes the preparation of SO3 from Na2S2O7 and sulfuric acid but without much details
please leave comments about my English in PM
|
|
Bedlasky
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1225
Registered: 15-4-2019
Location: Period 5, group 6
Member Is Offline
Mood: Volatile
|
|
HClO4 is weaker acid than H2S2O7. H0(HClO4) = -13, while H0("H2S2O7") = -14,44. I
refer to "H2S2O7" as 50 mole % SO3 in H2SO4.
|
|
SaccharinSlayer157
Harmless
Posts: 24
Registered: 1-10-2020
Location: Near Cou?
Member Is Offline
Mood: Resisting the urge to build a ketene lamp
|
|
This is not going as planned...
There is no way this is how I'm going to get my SO3, I seriously hope someone can help by suggesting an easier or more reliable method.
Even with a short path setup and anhydrous EVERYTHING the potassium salt still takes ages to melt and decompose under very strong heating and my yield
is reliably abysmal. So far all I've managed to do is convert less than 10ml of my initial sulfuric acid catalyst to what I assume to be a very dilute
oleum over the course of several frustrating runs.
I've heard something about a bisulfate approach? Apparently that proceeds through the same pyrosulfate though so I'll probably encounter the same
issues. Any other suggestions before I just cave and try to order P2O5 from firefox?
I ultimately need it to make oluem and then subsequently chlorofulfonic acid and I'm ready to move forward so any insight is greatly appreciated!
|
|
Deathunter88
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 513
Registered: 20-2-2015
Location: Beijing, China
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by SaccharinSlayer157 ![](images/xpblue/lastpost.gif) | This is not going as planned...
There is no way this is how I'm going to get my SO3, I seriously hope someone can help by suggesting an easier or more reliable method.
Even with a short path setup and anhydrous EVERYTHING the potassium salt still takes ages to melt and decompose under very strong heating and my yield
is reliably abysmal. So far all I've managed to do is convert less than 10ml of my initial sulfuric acid catalyst to what I assume to be a very dilute
oleum over the course of several frustrating runs.
I've heard something about a bisulfate approach? Apparently that proceeds through the same pyrosulfate though so I'll probably encounter the same
issues. Any other suggestions before I just cave and try to order P2O5 from firefox?
I ultimately need it to make oluem and then subsequently chlorofulfonic acid and I'm ready to move forward so any insight is greatly appreciated!
|
I would just go with P2O5. The bad news is that firefox is basically dead. The good news is that P2O5 is now easily available on Ebay.
|
|
Mateo_swe
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 526
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
Have you read Len´s book "Small-scale Synthesis Of Laboratory Reagents"?
Chapter 20 - Sulfur Trioxide and Oleum
Good book with preparations and good explanation and pics.
Do a online search for it, its a good book.
|
|
Keras
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 847
Registered: 20-8-2018
Location: (48, 2)
Member Is Offline
|
|
Quote: Originally posted by Mateo_swe ![](images/xpblue/lastpost.gif) | Have you read Len´s book "Small-scale Synthesis Of Laboratory Reagents"?
Chapter 20 - Sulfur Trioxide and Oleum
Good book with preparations and good explanation and pics.
Do a online search for it, its a good book. |
I’m planning to try the SO₃ synthesis mentioned in this book later this year. I have bought a suitable quartz round bottom flask, since standard
borosilicate glass would not survive the 700 °C+ temperature needed to decompose sodium bisulphate. I just to need to buy one or two more blow
torches to reach the proper temperature.
|
|
yobbo II
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 728
Registered: 28-3-2016
Member Is Offline
Mood: No Mood
|
|
The following is from the Bell Jar, the first five years page 3 - 8:
A magazine dedicated to vacuum.
Low temperature chemical reactions:
The reaction
NaHCO3 = Na2CO3 + H2O + CO2
which normally takes place at 270° C will take place at
room temperature in a vacuum of about 1 mm Hg.
Other reactions which take place at much lower
temperatures in a vacuum are the following:
Cr2 O3 + 3C = 2Cr + 3CO
CaC2 + 2 NaCl = CaCl2 + 2Na (vapor) + 2C
2MgO + CaO + Si + 2Mg (vapor) + CaSiO3
FeO + C = Fe + CO
These reactions are of great commercial importance.
Any reaction evolving gas will proceed at lower
temperature in vacuum.
END OF QUOTE
___________________________________
Would this be applicable to making SO3?
You would need a water aspirator as you are not going to use your mechanical pump, though you could use a piston (the type used nowadays) pump from a
fridge which I belived will pull a vacuum of about 1mm of Hg.
Yob
|
|
Keras
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 847
Registered: 20-8-2018
Location: (48, 2)
Member Is Offline
|
|
Quote: Originally posted by yobbo II ![](images/xpblue/lastpost.gif) |
The following is from the Bell Jar, the first five years page 3 - 8:
A magazine dedicated to vacuum.
Any reaction evolving gas will proceed at lower
temperature in vacuum. |
It's curious. The equation ∆G = ∆H - T∆S which relates the equilibrium constant to the temperature does not really explicitly depend on
pressure. One could argue that removing the gaseous products help drive the reaction to completion, which is certainly true. Maybe that explains it.
Maybe also S, and in a lesser extent H, depend on P. Maybe operating under reduced pressure increases ∆S, which automatically means that a lower T
is needed to reach the same equilibrium.
As to the synthesis of SO₃, I’m not certain it would be helpful. You would end up with sulphur trioxide being sucked into your vacuum pump, which
could lead to… much inconvenience.
[Edited on 27-1-2023 by Keras]
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Keras ![](images/xpblue/lastpost.gif) |
It's curious. The equation ∆G = ∆H - T∆S which relates the equilibrium constant to the temperature does not really explicitly depend on
pressure.
[Edited on 27-1-2023 by Keras] |
It implicitly depends on it. the entropy of a material- particularly a gas- is pressure dependent.
|
|
Keras
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 847
Registered: 20-8-2018
Location: (48, 2)
Member Is Offline
|
|
Does the entropy increases or decreases with pressure?
|
|
Junk_Enginerd
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 250
Registered: 26-5-2019
Location: Sweden
Member Is Offline
|
|
Quote: Originally posted by SaccharinSlayer157 ![](images/xpblue/lastpost.gif) | This is not going as planned...
There is no way this is how I'm going to get my SO3, I seriously hope someone can help by suggesting an easier or more reliable method. !
|
Sure. I can vouch for sodium bisulfate. Easy to get, standard pool chemical. Then heat the crap out of it and SO3 comes out! By my estimate I heated
it to 650°C, just beyond incandescence. It makes the glassware single use for sure, but that's what test tubes are for.
|
|
SaccharinSlayer157
Harmless
Posts: 24
Registered: 1-10-2020
Location: Near Cou?
Member Is Offline
Mood: Resisting the urge to build a ketene lamp
|
|
Hallelujah!
So I decided to bite the bullet and bought 500g of P2O5 off ebay. Very much
worth not having to deal with high temps and abysmal yields IMO (Plus I still have a bunch left over to play with later ). After reading a bit more and finding THIS thread with a helpful Engager post I found immediate success...
50ml 98% sulfuric acid with 100g phosphorous pentoxide at medium heat distilled directly into more H2SO4 yielded what I estimate to be ~50% free SO3
oleum in less than 45 min, no problem. Next stop, HSO3Cl!
Only "issue" was that if I didn't keep my condenser water warm enough (It's pretty cold in North Texas atm), the SO3 would crystallize in the
receiving flask and plug it until I could warm the incoming distillate back up again. Got some lovely formations though I'm sure y'all will
appreciate...
![SO3 Crystal Zoom.jpg - 643kB](https://www.sciencemadness.org/whisper/files.php?pid=681408&aid=97006)
Also, a syrupy almost taffy like goop was left in the receiving flask. I assume this is mainly polyphosphoric acid, leftover sulfuric, and some other
mixed phosphoric acids? I saved it and am keeping it dry for now. Anyone have any ideas on how this might be useful or is it really just waste?
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3631
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
I've never seen SO3 before, gas, liquid or solid.
Thanks for the photos.
The leftover in the pot would, I guess, be a very good general purpose dessicant.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
BromicAcid
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3237
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Boy, it can be nerve wracking when stuff starts freezing on the drip tip like that. I usually keep a heat gun handy for low melters but sometimes
it's hard to melt out the tip with the void space. I mean, you obviously never want to get it blanked off and potentially build pressure in the
setup. Nice crystals though.
Edit: I should mention that it's usually even more of a pain for me since the setup is usually under vacuum and thus the heat from the outside glass
portion has an even more difficult (next to impossible time) getting that inner drip tip melted out.
[Edited on 2/10/2023 by BromicAcid]
|
|
Herr Haber
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
Congratulations, beautiful pictures !!!
Quote: Originally posted by SaccharinSlayer157 ![](images/xpblue/lastpost.gif) |
Only "issue" was that if I didn't keep my condenser water warm enough (It's pretty cold in North Texas atm), the SO3 would crystallize in the
receiving flask and plug it until I could warm the incoming distillate back up again. Got some lovely formations though I'm sure y'all will
appreciate...
|
I'm sure you can find a heat GUN in Texas !
But these are so beautiful I'm happy you didnt have one at that moment
The spirit of adventure was upon me. Having nitric acid and copper, I had only to learn what the words 'act upon' meant. - Ira Remsen
|
|
ErgoloidMesylate
Banned
![*](images/xpblue/star.gif)
Posts: 89
Registered: 8-8-2022
Location: Norad
Member Is Offline
Mood: Freedom of thought is priceless - You can't afford it
|
|
Quote: Originally posted by SaccharinSlayer157 ![](images/xpblue/lastpost.gif) | This is not going as planned...
There is no way this is how I'm going to get my SO3, I seriously hope someone can help by suggesting an easier or more reliable method.
Even with a short path setup and anhydrous EVERYTHING the potassium salt still takes ages to melt and decompose under very strong heating and my yield
is reliably abysmal. So far all I've managed to do is convert less than 10ml of my initial sulfuric acid catalyst to what I assume to be a very dilute
oleum over the course of several frustrating runs.
I've heard something about a bisulfate approach? Apparently that proceeds through the same pyrosulfate though so I'll probably encounter the same
issues. Any other suggestions before I just cave and try to order P2O5 from firefox?
I ultimately need it to make oluem and then subsequently chlorofulfonic acid and I'm ready to move forward so any insight is greatly appreciated!
|
Wiki mentions using a tin salt at a lower temp.
Another two step method involving a salt pyrolysis starts with concentrated sulfuric acid and anhydrous tin tetrachloride:
Reaction between tin tetrachloride and sulfuric acid in a 1:2 molar mixture at near reflux (114°C):
SnCl4 + 2 H2SO4 → Sn(SO4)2 + 4 HCl
Pyrolysis of anhydrous tin(IV) sulfate at 150°C - 200°C:
Sn(SO4)2 → SnO2 + 2 SO3
The advantage of this method over the sodium bisulfate one is that it requires much lower temperatures and can be done using normal borosilicate
laboratory glassware without the risk of shattering.
Cannula transfer and cannula filtering is used for lysergic synth Compressed air and remove co2
|
|
Raid
Hazard to Everyone
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 201
Registered: 14-11-2022
Location: N/A
Member Is Offline
Mood: School
|
|
Is there a way of recovering the P2O5 after the oleum synthesis? Maybe like drying it at a very high temp or something?
|
|
Pages:
1
2 |