thioacetone
Harmless
Posts: 16
Registered: 15-12-2022
Member Is Offline
|
|
vacuum distillation of cyclohexane
How would I design a cold trap to stop cyclohexane vapors getting into my vacuum pump? The melting point of cyclohexane is 6.6 degrees C.
|
|
j_sum1
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 6256
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Organised
|
|
I think that running chilled water in your distillation and putting your receiving flask in a cold water bath, you should be fine. Obviously you don't
want it freezing and blocking your cond|nser. So, keep everything above 6.6.
|
|
gemar14
Harmless
Posts: 16
Registered: 14-5-2019
Member Is Offline
|
|
Quote: Originally posted by thioacetone ![](images/xpblue/lastpost.gif) | How would I design a cold trap to stop cyclohexane vapors getting into my vacuum pump? The melting point of cyclohexane is 6.6 degrees C.
|
Alternatively, you could just do atmospheric pressure distillation. The boiling point of cyclohexane is only around 80 C
|
|
thioacetone
Harmless
Posts: 16
Registered: 15-12-2022
Member Is Offline
|
|
I can't use heat as I am evaporating solvent from organic plant material (to make an extract) and heat will degrade the product.
I have tried using chilled water in the condenser and submerging the receiving flask in ice water, but half of my solvent just disappears (into the
pump).
|
|
j_sum1
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 6256
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Organised
|
|
Cold temperatures:
Chilled water
Ice and salt bath
Dry ice
Dry ice and acetone
Liquid nitrogen
Pick what works for the solvent and level of vacuum.
Sounds like you might need something colder for the condenser. You could use car antifreeze chilled down to the temperature you need.
I have seen on this site a table of salt/ice baths and the temperatures that can be sustained with each combination. Worth a search.
|
|
Rainwater
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 870
Registered: 22-12-2021
Member Is Offline
Mood: indisposition to activity
|
|
Or use less of a vacuum.
Without a proper manometer you can eye ball the pressure. But it is tricky
Keep your coolant in ice as well as the receiver.
Heat your solvent to something like 5 degrees above room temp,
then ever so slowly open a valve leading to your vacuum.
When you start hearing air move through the vacuum pump, close the valve just a little.
Now wait, first your solvent will degas. Take it slow.
If it doesnt then open the valve a little more
When it starts boiling close the valve.
If your appratus is properly sealed,
the condenser will maintain the vacuum level and your set
If your reciving flask or condenser get too hot then the pressure will increase,
as well as the boiling point
If you have a leak, same effect
"You can't do that" - challenge accepted
|
|
thioacetone
Harmless
Posts: 16
Registered: 15-12-2022
Member Is Offline
|
|
I will try using a lower boiling point solvent (pentane) and just use conventional distillation
Thank you for the suggestions
I think I would have to buy a proper cold trap and use dry ice/acetone if I want to properly capture the cyclohexane vapours. I can't afford a cold
trap and the cost of ongoing purchases of dry ice every time I want to vacuum distil is excessive.
The reason I want to capture all/most of the vapours is because cyclohexane is quite expensive here. If I am vacuum distilling a different cheaper
solvent (e.g. ethanol) I would not really care as much about the vapours. I can just change vac pump oil as needed.
[Edited on 17-1-2023 by thioacetone]
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3634
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
You could add a second chilled condenser above the receiving flask and attach that to the pump.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
thioacetone
Harmless
Posts: 16
Registered: 15-12-2022
Member Is Offline
|
|
That's a good idea. I did consider using a condenser as a makeshift cold trap.
I am worried about the cyclohexane freezing in the condenser and blocking it though. It freezes at 6.6 deg C. I can imagine this problem would be
worse with a spiral condenser compared to a Liebig
|
|