Mixe
Harmless
Posts: 41
Registered: 2-6-2017
Member Is Offline
Mood: No Mood
|
|
Keep the temperature
Ok, so noob question time.
I have a heating mantle with stirrer which sort of works great, able to reach temps well over 350 and great for distillations where most of the
vapours keep a constant temperature by the boiling point.
Unfortunately it has no automatic temperature control, and the heating knob is not graded at all, so when I actually need to keep a refluxing reaction
mixture at a constant temp it’s a damn guessing game.
Anyone have any good tricks to get this sorted? I’m running a reaction that needs to keep 60C constantly for six hours, and I just over- or
undershoot all the time, desperately correcting the knob.
What should I do to find the temp setting for this bugger? I know I know I should get a heating plate with temp settings, but I honestly don’t have
the money right now. Any tips?
|
|
|
violet sin
International Hazard
Posts: 1480
Registered: 2-9-2012
Location: Daydreaming of uraninite...
Member Is Offline
Mood: Good
|
|
PID temperature control for your device would be a cheap fix. In my experience, Most come with a thermocouple probe, an SSR and some lies about
being a le to drive that thing directly. But it's been a few years since I've had to chase my tail on this subject. I'm speaking of the REX100C PID
controller that was about 13$.
https://www.ebay.com/itm/165653821639
There's a simple way to extend the measurement range with menu button pressing. Opens more possibility than 0-400°F.
You can bypass the internal Relay to hijack 12v to activate the included SSR easily.
This hobby will teach you a lot about all kinds of equipment, how to overcome obstacles and press on.
|
|
|
Mixe
Harmless
Posts: 41
Registered: 2-6-2017
Member Is Offline
Mood: No Mood
|
|
This was more or less what I had in mind, but I thought I would have to construct it from an arduino. Great tip, thank you! question is how I connect
this to a heating mantle of this type (which is what I have):
|
|
|
BromicAcid
International Hazard
Posts: 3244
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Put some marks on it when you figure out boiling points. You'll get to know your dial with practice and you'll use those marks even if you never boil
the same things again as a guide. Practice is really what is going to fix your issue. I've used PIDs before but they're not very useful for
distillation and even in reflux you need someone to figure out the reflux temperature (i.e., even if you're in a solvent of a known boiling point it
can be altered by the constituents). There's a lot of finesse to chemistry that I thought early on were easy things to plan for but ended up being
more skill than textbook.
|
|
|
Sulaiman
International Hazard
Posts: 3692
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
For fractional distillations I like to use a 'dimmer' (phase angle) type controller
(settable constant power) for stability.
To maintain a constant temperature I use pid controllers (REX-C100 and others)
Your mantle has stirring so you'd need to keep that as-is and bring out separate wires from the heating element to your controller.
Wiires inside the mantle should have high temperature insulation, ie NOT normal pvc insulation.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
Johnny Cappone
Hazard to Self
Posts: 74
Registered: 10-12-2020
Location: Brazil
Member Is Offline
|
|
A PID controller would be a good choice, although it's a bit of a bulky device. Like @Sulaiman, I have successfully used "dimmer" type controllers to
control heat output from electrical resistances. They are also useful for controlling the rotation of tools that use universal electric motors. A
dimmer module is usually slightly cheaper than a PID controller and can also be used to get a "more-or-less-constant" temperature once the adjustment
where the heat produced by the heating element and the lost heat is found.
I believe that these (PID and dimmer controllers) are the cheapest alternatives to solve the problem. Some research on YouTube can shed more light on
the differences between them. Once you've made your decision, just buy one of them and, if necessary, ask for help on the installation. It's a really
pretty basic procedure.
 
|
|
|
Mixe
Harmless
Posts: 41
Registered: 2-6-2017
Member Is Offline
Mood: No Mood
|
|
Thank you all for excellent feedback and ideas.
I can do without YouTube, I’m an old time electronics hobbyist and programmer and it shouldn’t be a problem to hook this up, also to my newly
designed ArduinoCode- based pH/ temp measure/control panel with touchscreen. I’ll be posting info and schematics to this shortly, now with PID
included.
Regards
M
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
