Pages:
1
2
3
4
5 |
Rainwater
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 870
Registered: 22-12-2021
Member Is Offline
Mood: indisposition to activity
|
|
May i suggest testing/purifying your H2SO4
Lots of videos out there about this subject. Your initial distillate should smell sweet, don't go sniff it. It's a powerful smell that will fill an
outside area if it's not too windy
"You can't do that" - challenge accepted
|
|
TLutman
Harmless
Posts: 26
Registered: 13-10-2019
Member Is Offline
|
|
I have about 500ml of distilled H₂SO₄ left and a couple liters of liquid fire drain cleaner. I am hoping to stretch the distilled until another
warm spell hits, as I would prefer to do it outdoors away from all my machine tools and it is looking like cold and snow for … who knows?
I originally did this with the distilled with the same results, even though I used NaOH at the time. I did grab some Prestone concentrated while in
town today. I’m going to try it here tonight and see which way it goes. I really want to get all the glassware cleaned up because it smells. Yes
there is some sweet smell in the last flask, but the yield is very minimal.
|
|
alexrandomkat
Harmless
Posts: 7
Registered: 23-1-2023
Member Is Offline
|
|
Just tried out my own attempt at dioxane, and I got what I wanted, although it was stopped not by prudent choice but by me yeeting the receiver before
a sludge volcano came over (luckily all contained in glassware).
How are people dealing with the waste from this, given throwing dioxane down the drain is not the best of ideas? Is absorbing it into something,
sealing in bags, and using the trash acceptable?
Was on my mind since I'll have more clean-up than expected...
|
|
Fery
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1003
Registered: 27-8-2019
Location: Czechoslovakia
Member Is Offline
|
|
alexrandomkat - no tar, no volcano: https://www.sciencemadness.org/whisper/viewthread.php?tid=65...
|
|
alexrandomkat
Harmless
Posts: 7
Registered: 23-1-2023
Member Is Offline
|
|
Thanks, should have read that thread before I started...
Just stopping a tad earlier would have saved me a lot of hassle now.
|
|
Fery
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1003
Registered: 27-8-2019
Location: Czechoslovakia
Member Is Offline
|
|
Use less acid and bigger flask or put smaller volume into your flask. You can repeatedly add fresh ethylene glycol and resume synthesis. I used 1 L
flask and filled 300 ml into it, distilled out 200 ml so remainder in flask 100 ml... then added fresh 200 ml of glycol and repeated (4 cycles
totally). Finally I distilled the content from flask a little more so only 50 ml remained inside (from that 11 ml should be H2SO4). Could be done
using dropping funnel instead adding glycol on cycles. When I saw the disastrous situations on youtube I postponed this synthesis for more than 1
year. Meanwhile I luckily found better sources like using 3 times less of catalyst and bigger flask filled less. I wonder whether H3PO4 could be used
instead of H2SO4 but I usually do not repeat experiments as I have long list of new experiments to do. Meanwhile I also bought a lot of 1,4-dioxane
from es-drei.de
|
|
TLutman
Harmless
Posts: 26
Registered: 13-10-2019
Member Is Offline
|
|
Interesting update. I finally got around to cleaning up all the different fractions I collected from both the ethylene glycol distill and dioxane.
There was perhaps 30-40mL total. I put them all in a gallon jug (empty distilled water). All those test tubes were capped, since I really don’t care
for the smell of it.
There was one last tube in that rack, unmarked and open with a mL or so of a clear liquid. It couldn’t be to volatile, and being from the same
time I just put it in the same jug.
A few seconds later, all the vapors ignited in a single woof. I felt the jug, but no heat was noticed.
I wish I knew what was in the open tube, and why it reacted the way it did.
Also regret assuming it was fine to just throw in with the dioxane/EG/ mystery yellow liquid.
|
|
Rainwater
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 870
Registered: 22-12-2021
Member Is Offline
Mood: indisposition to activity
|
|
If this stuff has been sitting, waiting for 3 months, it likely formed peroxides
"You can't do that" - challenge accepted
|
|
Fery
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1003
Registered: 27-8-2019
Location: Czechoslovakia
Member Is Offline
|
|
After that 350 g of the product stayed in 0,5 l bottle for almost 1 year in a fridge at +4C, in the bottom part of the flask a solid block of product
was formed and the liquid moved above. This happened due to higher density of solid 1,4-dioxane and lower density of liquid phase (this also ensures
the flask does not break unlike water expanding during freezing) and hundreds (or maybe almost thousand) of partial thaw / resolidification cycles by
small temperature oscillations in the fridge.
I poured the top liquid phase (which volume increased from 20 ml into 100 ml during 1 year) into another flask and let magnetically stirred with 2 g
of 90% KOH for 1 day. Most of KOH dissolved but still some solid KOH remained. There was a reaction very likely aldol condensation (remaining of
acetaldehyde ???) because the content turned into yellow and after few hours into brownish. After turning off the stirring a dark brown mess settled
to the bottom and the upper phase was filtered through filter paper into new clean flask using gravity filtration. 1 g of calcium metal (small 5
granules forged with hammer into thin pieces to expose fresh surface) was added to the yellowish filtrate and there was very slow and tiny bubbling of
H2. I let it to magnetically stir for 1 day and then redistill.
The 250 g of solid dioxane block was let to melt at room temperature and then magnetically stirred with 2 g of KOH, but this was very likely
unnecessary, this solid phase seems to be very pure (and no liquid seems to be trapped among crystals inside the solid block): there was no reaction
with KOH and it stayed completely clear and colorless, pellets of KOH seems to be still dry and not covered with a layer of liquid. I later added 0,25
g of calcium metal forged with hammer into thin pieces with exposed fresh metal surface and there was no reaction either. So this phase seems to be
very pure and also anhydrous. I'll redistill it too. There is no need to add KOH either drying agent (Ca or Na) into this phase, either
redistillation. Just let you know what I tried and what seems to be unnecessary.
Letting the product to sit in a fridge for 1 year seems to be enough for the purification. Initially the upper liquid phase was circa 20 ml, but
during time the trapped liquid moved from the bottom solid phase to the top liquid phase and it was easy to separate it by just simply pouring it out.
It is also a good idea to let the solid dioxane in the fridge until its usage for e.g. as a solvent for a Grignard reaction. In its solid form at +4 C
fridge temperature it is pure, anhydrous, no risk of peroxide formation.
Patience is our biggest helper.
[Edited on 16-7-2023 by Fery]
|
|
B(a)P
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1139
Registered: 29-9-2019
Member Is Offline
Mood: Festive
|
|
I am in need of some 1,4-dioxane for an an experiment that I intend to do once I have sourced the required regents and solvents. I intend to make the
1,4-dioxane via dehydration of ethylene glycol with sulfuric acid. I recently purchased some impure ethylene glycol (anti freeze) for this purpose.
What I have unfortunately realised since purchasing the ethylene glycol is that it is 50% water.
Is it worth distilling the ethylene glycol to remove the water before I attempt the dehydration reaction with sulfuric acid?
|
|
j_sum1
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 6256
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Organised
|
|
I would.
That said, I have never been very successful at dioxane synthesis. I have used ~100% ethylene glycol and also the same stuff pre-distilled. I think
I have lost a lot in the work-up with NaOH or KOH and made a lot of tarry goop. Which is to say, my advice might not count for a whole lot.
|
|
B(a)P
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1139
Registered: 29-9-2019
Member Is Offline
Mood: Festive
|
|
Thanks, I have never tried the synthesis, so any advice is most welcome. I was concerned my crude product would be too dilute and the dioxane I
produced would get mostly lost when I was trying to pull the water out. I will get rid of the water first.
|
|
Fery
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1003
Registered: 27-8-2019
Location: Czechoslovakia
Member Is Offline
|
|
Certainly remove the water as much as you can. During the reaction use only less of the catalyst, not 10%. 4% was enough in my case. You can add fresh
ethylene glycol then and repeat few cycles. Do not overfill the flask. Filling for only 1/3 is better than filling 1/2 of the flask.
|
|
Sir_Gawain
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 324
Registered: 12-10-2022
Location: Due South of Due West
Member Is Online
Mood: Way less sad
|
|
Runaway polymerization during dioxane synthesis?
While making dioxane yesterday for the first time, I noticed something strange. I was using unpurified antifreeze (300 mL) and purified drain cleaner
acid. The distillation went pretty smoothly for the first two hours, with none of the tar people talk about. It did slowly grow darker until it was
almost black, but there was no foaming. The vapor temperature had been fairly stable at around 110*C, but when around 100 mL was left in the boiling
flask the temperature suddenly spiked. It climbed to over 120*C and a lot of distillate came over very rapidly, maxing out my condenser. Even though I
immediately turned off the heat it continued to keep going. About 50 mL came over in just a few minutes. Tar also started to form, and foamed up
almost to the condenser.
Could the rapid polymerization reaction cause the heating? The exothermic reaction that forms Bakelite comes to mind. Usually, it seems the tar forms
over a couple minutes. Mine, however, formed all at once. I did add a little less sulfuric acid than most people(30 mL).
![IMG_0093.jpeg - 3.1MB](https://www.sciencemadness.org/whisper/files.php?pid=688947&aid=100069)
End result.
[Edited on 11-27-2023 by Sir_Gawain]
“Alchemy is trying to turn things yellow; chemistry is trying to avoid things turning yellow.” -Tom deP.
|
|
Fery
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1003
Registered: 27-8-2019
Location: Czechoslovakia
Member Is Offline
|
|
what was your ratio of ethylene glycol : H2SO4
volume of your flask and volume of reactants?
|
|
Sir_Gawain
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 324
Registered: 12-10-2022
Location: Due South of Due West
Member Is Online
Mood: Way less sad
|
|
300 mL antifreeze, 30 mL sulfuric acid, 500 mL flask.
“Alchemy is trying to turn things yellow; chemistry is trying to avoid things turning yellow.” -Tom deP.
|
|
Texium
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4547
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
Oof. I don’t envy the task you have ahead of you with cleaning that flask.
I can’t explain what happened, but I recommend carefully re-distilling your product, because who knows what all came over when the temperature
spiked.
|
|
Sir_Gawain
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 324
Registered: 12-10-2022
Location: Due South of Due West
Member Is Online
Mood: Way less sad
|
|
It actually wasn’t that bad. Hot water got most of it out, a little acetone removed the rest.
I’m going to fractionally distill it, dry over sodium hydroxide, and distill again.
“Alchemy is trying to turn things yellow; chemistry is trying to avoid things turning yellow.” -Tom deP.
|
|
Fery
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1003
Registered: 27-8-2019
Location: Czechoslovakia
Member Is Offline
|
|
for 300 ml glycol you should use 1 L flask and 11 ml of H2SO4
distill out 200 ml of product and then add fresh 200 ml of glykol into the flask and repeat few times
|
|
Sir_Gawain
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 324
Registered: 12-10-2022
Location: Due South of Due West
Member Is Online
Mood: Way less sad
|
|
Only 11 mL of sulfuric acid for 400+ mL of glycol? I reasoned less sulfuric acid would cause less tar, but that seems like a lot less.
“Alchemy is trying to turn things yellow; chemistry is trying to avoid things turning yellow.” -Tom deP.
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2690
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
Likely you made some polyethylene glycol in the process, that might happen if mostly glycol and not enough acid. The acid might help stop the
polymerization and make dioxane rather than chain elongation.
|
|
Fery
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1003
Registered: 27-8-2019
Location: Czechoslovakia
Member Is Offline
|
|
Everyone repeats the mistakes of former home lab experimenters although everyone sees the consequences. I postponed this synthesis for few years only
due these nasty looking experiences - black tar and messing apparatus with it. If at least one had did the experiment properly I did it few years
earlier.
Here the method to avoid nasty experiences:
https://www.sciencemadness.org/whisper/viewthread.php?tid=65...
Use 1/3 of the H2SO4 amount the unhappy experimenters used and use twofold volume flask compared to them.
Distill off only 2/3 of the content from the flask. Then you can add the consumed glycol amount and resume. You can perform few such
cycles.
https://www.sciencemadness.org/whisper/viewthread.php?tid=15...
|
|
monolithic
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
It's been a few years since I've made any but I remember having to carefully control the power output on my heating mantle. Toward the end of the
distillation it will go crazy and foam out of control, so you have to babysit it and taper down the power and play with the stirring speed, and there
will be a point where you have to call it quits. You can push the distillation pretty far, however.
I used a 1L round bottom flask + 350 ml ethylene glycol (distilled from antifreeze concentrate) + 35 ml unbuffered drain cleaner straight from the
bottle (tested as 93% w/w concentration.) http://www.sciencemadness.org/talk/viewthread.php?tid=84819&...
[Edited on 11-29-2023 by monolithic]
|
|
Texium
|
Threads Merged 29-11-2023 at 09:03 |
Texium
|
Threads Merged 29-11-2023 at 09:04 |
Texium
|
Threads Merged 29-11-2023 at 09:09 |
Texium
|
Thread Topped 29-11-2023 at 09:10 |
Texium
|
Thread Moved 29-11-2023 at 09:11 |
Texium
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4547
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
Here you go: the dioxane sticky thread that people have been wanting for years but was never made!
[Edited on 11-29-2023 by Texium]
|
|
Sir_Gawain
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 324
Registered: 12-10-2022
Location: Due South of Due West
Member Is Online
Mood: Way less sad
|
|
Thanks, Texium!
Fery, I’ll try your method next time.
Another improvement I discovered is, when drying the impure dioxane azeotrope over sodium hydroxide, to add about 30 grams of sodium hydroxide per 150
mL of dioxane and let it dissolve. At this point, Nurdrage added more sodium hydroxide and it all gummed up and solidified. Instead, drain off the
bottom aqueous sodium hydroxide layer and add another 30 grams of sodium hydroxide to the dioxane. You lose a lot less dioxane this way. It’s also
probably drier.
“Alchemy is trying to turn things yellow; chemistry is trying to avoid things turning yellow.” -Tom deP.
|
|
Pages:
1
2
3
4
5 |