Mateo_swe
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 526
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
Learn using TLC for analysis
I want to try learn using TLC plates to analyze various compounds (compare them to a known substance)
Now i wonder what is the best TLC plates to get when starting this learning experience.
I have no specific type of compounds to analyze in mind, it will be used on many things so a plate that is usable on a broad spectrum of compounds is
best if that is possible.
Would the standard silica based plates be good choice and should i get 20x20cm or smaller size?
I see there are glass, aluminum or plastic backed plates.
I have read some TLC plates can be cut or divided into smaller sections and that might be good when learning.
Witch type of plates can be cut into smaller sections?
Also one can get the plates with or without F254.
If i understood this correctly this is a additive to the plate that makes it glow under UV to enhance the visibility of the spots.
Should i use F254 plates?
|
|
j_sum1
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 6256
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Organised
|
|
The Home Scientist on YT (Robert Bruce Thompson RIP) has a video showing how to make your own TLC plates very cheaply. He has follow up videos
showing how to use them.
You might be interested in these.
|
|
AvBaeyer
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 646
Registered: 25-2-2014
Location: CA
Member Is Offline
Mood: No Mood
|
|
1. Use F254 dopped plates and get a short wavelength uv source for visualization. Keep in mind that iodine is usually good for visualization. There
are also many kinds of sprays and "dips" used.
2. I recommend getting commercial glass microscope slide size silica plates if you can afford them. These are typically about 2.5 cm x 7.5 cm in size.
I cut these in half to get a 2.5 x 3.75 cm miniplate which I use for all initial solvent selection experiments as well as other uses. A good glass
cutter is essential. To spot these miniplates you need a very fine capillary so that you typically spot 1 -2 microliters of sample. Experience will
teach you how to do this effectively. You can note the size of your spot under uv before the plate is developed and add more if necessary. I can
easily run 3-4 spots side by side on these plates (in the long direction) which is very useful for following reactions or column separations. When
required you can use the full-length plate.
3. Buying very large plates and trying to cut them will result in considerable waste. Believe me on this. There used to be plates sold that were
prescored to easily break into smaller plates. Perhaps these are still offered somewhere (Analtech comes to mind.)
4. My experience with plastic and aluminum plates is minmal. I really do not like them for a variety of reasons. Their only attraction is that they
are relatively cheap.
5. Making your own plates is an art form not easily mastered. Also getting your hands on useful TLC adsorbents formulated for plate making is not
easy. I guess it just depends on how deeply you want to learn the technology.
AvB
|
|
Organikum
resurrected
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2336
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: frustrated
|
|
Now whats a "good glasscutter"? You talk about the expensive diamond tipped ones or those with the wheels?
|
|
Mateo_swe
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 526
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
OK, thanks for all info.
Ill check out The Home Scientist on YT and the TLC videos.
So, F254 plates is good, use smaller glass backed variants, pre-scored if avaliable otherwise small 2.5 x 7.5cm.
Get some capillary tubes for spotting and a 245nm UV source.
I have Iodine i can use and i think i stick with purchased plates and look at homemade plates later if i use it a lot.
I have one of those glass cutters/scorers with a small wheel on the top, will it do the scoring job or do i need a more proffesional one?
|
|
AvBaeyer
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 646
Registered: 25-2-2014
Location: CA
Member Is Offline
Mood: No Mood
|
|
Some further comments-
Good glass cutter: I use a wheel type which I bought at Ace hardware. It is one of the more expensive ones made in Germany. I also use a diamond
stylus but I prefer the wheel cutter. When cutting plates, they need to be face down. I recommend a clean, thick piece of glass as a work surface.
TLC plates: I use Whatman silica gel plates although several reputable brands can be had on Ebay. I do not recommend Chinese plates. My experience
with these several years ago showed inconsistent quality from plate to plate. Perhaps they have improved over the years.
TLC spotting: I use Drummond 2 microliter "disposable" micropipettes. They are somewhat expensive but can easily be cleaned and reused. A vial of 100
has been recycled several times and has lasted for several years. I found them on Ebay. You can also pull your own capillaries from disposable glass
pipettes. The secret to a good TLC experiment is a very small tight spot of a not so concentrated sample. Good spotting is an art form easily learned
from experience.
Other TLC methods: Paper chromatography using Whatman products can be very useful for a variety of analytical methods. Water based eluents can be used
whereas standard silica plates do not fare too well with aqueous eluents. The paper can also be chemically modified to change its properties. For
example, it can be acylated with activated carboxylic acids to make it more lipophilic or give it an "aromatic surface" with, for example, benzoic
acid. This is somewhat analogous to reverse-phase silica plates.
AvB
|
|
Oxy
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 140
Registered: 1-12-2020
Member Is Offline
|
|
Quote: Originally posted by AvBaeyer ![](images/xpblue/lastpost.gif) |
TLC spotting: I use Drummond 2 microliter "disposable" micropipettes. They are somewhat expensive but can easily be cleaned and reused.
|
That looks nice.
At university I used to make my own spotters from Pasteur pipette using Bunsen burner. At my home lab I am sometimes using melting point capillary
tubes but those are not as thin as stretched glass fibre and require more caution as they can produce larger spots
|
|
Mateo_swe
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 526
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
I see the glass TLC plates on Ebay are expensive, very expensive if its a known good brand.
400Euros for 20pcs of Merck glass silica F254 20x20cm plates, ouchh...
The chinese plates are much cheaper, about 100Euros for 80pcs, 2.5x7.5cm similar to the ones below, but they are no good you say, or can they be used?
Chinese plates
Found these plates for about 160Euros with shipping, 80pcs/box
Glass Backed TLC Classical Silica Plate - Silica Gel 60 F254 2.5 X 7.5Cm
Glass backed TLC classical silica plates, silica gel 60, F254, 2.5x7.5cm
Manufacturer is Lichen cottage, shipped from Florida US.
Maybe an option.
[Edited on 2022-10-10 by Mateo_swe]
|
|
AvBaeyer
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 646
Registered: 25-2-2014
Location: CA
Member Is Offline
Mood: No Mood
|
|
Mateo_swe,
I did not say the chinese plates were no good. I said that several years ago plate to plate quality was inconsistent. They were useable but with some
caution. If you want to learn silica gel based tlc, the chinese plates should work ok for you. And yes, commercial plates are very expensive, but you
really cannot run organic chemistry reactions without them. Perhaps you might try paper chromatography first. Whatman chromatography paper strip is
sold as a roll, or you can sometimes buy sheets. I noticed some products available on Amazon searching for "Whatman chromatography paper." Also, a
really good office supply store just might still have high quality blotter paper which can be used for chromatography.
AvB
|
|
Mateo_swe
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 526
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
Hmm, i think i have to pay up for some at least decent plates as i really would like to learn TLC analysis.
I take my chances on the plates made by Lichen cottage.
80pcs will last a while for me, hopefully enough to learn the basics.
|
|
Oxy
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 140
Registered: 1-12-2020
Member Is Offline
|
|
Quote: Originally posted by Mateo_swe ![](images/xpblue/lastpost.gif) | Hmm, i think i have to pay up for some at least decent plates as i really would like to learn TLC analysis.
I take my chances on the plates made by Lichen cottage.
80pcs will last a while for me, hopefully enough to learn the basics. |
That will be definitelty enough noto only for learning but for some concrete application as well. If you cut them in a half you get 160 2.5 X 3.75
which should last you for a while (depending on what you do)
|
|
Mateo_swe
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 526
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
I have ordered TLC plates, two 270nm UVC diodes with a power supply (to build a TLC UV visualizer device) and i think i have the rest needed.
Thanks for all info.
|
|