Gargamel
Hazard to Others
Posts: 166
Registered: 9-3-2013
Member Is Offline
Mood: No Mood
|
|
How to use a PT100 resistor in corrosive environment
Hi guys,
I'd like to use a PT100 to monitor processes where you expect a steel probe to get attacked.
You can buy glass covered probes, but I don't want to pay a lot of money.
Also a lot of European shops do not deliver to private individuals.
Something like a resistor in a hollow glass rod...
Would have a high thermal resistance, but still better than a probe outside the reaction vessel.
Do you have some proven home recepies?
|
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
The price sucks, but you could copy this sort of thing.
https://www.sigmaaldrich.com/GB/en/product/aldrich/z552445
|
|
|
Fulmen
International Hazard
Posts: 1725
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
Define corrosive. Epoxy or RTV can handle a lot of chemicals that would attack steel.
We're not banging rocks together here. We know how to put a man back together.
|
|
|
Gargamel
Hazard to Others
Posts: 166
Registered: 9-3-2013
Member Is Offline
Mood: No Mood
|
|
Nascent chlorine, diluted nitric acid... both at up to some 80°C...
|
|
|
CharlieA
National Hazard
Posts: 646
Registered: 11-8-2015
Location: Missouri, USA
Member Is Offline
Mood: No Mood
|
|
If you have, or can get, soda lime glass you should be able to prepare a glass sheath for the probe. Or maybe narrow test tube could be used.
|
|
|
WGTR
National Hazard
Posts: 971
Registered: 29-9-2013
Location: Online
Member Is Offline
Mood: Outline
|
|
A cheapo propane torch isn't usually enough to fuse borosilicate glass tubing by itself. However, I have found that it was still barely possible to
fuse glass joints with propane preheating coupled with a small pin-point butane torch directed at the areas that needed fusion.
Or like Charlie mentioned, soda lime glass tubing is fusible with propane.
|
|
|
Rainwater
National Hazard
Posts: 938
Registered: 22-12-2021
Member Is Offline
Mood: Break'n glass & kick'n a's
|
|
Soda glass tubes are easy to work with.
Just seal one end. It can be melted with a candles heat and purchased from most hobby shops
"You can't do that" - challenge accepted
|
|
|
ManyInterests
National Hazard
Posts: 942
Registered: 19-5-2019
Member Is Offline
|
|
As someone who has had a PT100 probe busted by being corroded by sodium chlorate synthesis (it was not very pure sodium chlorate. I still need to
purify it) I also was looking for solutions to this problem.
My need is compounded by the fact that I plan on making picric acid in the future. As we all know, picric acid and metals generally do not like each
other and they will form highly sensitive picrates and I want to prevent that at all costs.
I ordered this batch of borosilicate tubes off aliexpress: https://bit.ly/3QcW3p2
I have a rough estimate of what diameter my prob is, but the 6mm ID (7mm - 1mm thickness) should be sufficient to house my probe, as well as some good
thermal paste to allow for accurate temperature reading.
| Quote: | | A cheapo propane torch isn't usually enough to fuse borosilicate glass tubing by itself. However, I have found that it was still barely possible to
fuse glass joints with propane preheating coupled with a small pin-point butane torch directed at the areas that needed fusion.
|
Isn't propane hotter than butane? I think I did see videos on ampuling chemicals in test tubes using propane torches? That is what I plan on doing is
closing off one end with a propane torch. Even if it doesn't fully cover the thermal probe, I never had to fully immerse it in any solution, so I can
just secure the other end with electrical tape and it should be OK.
|
|
|
Twospoons
International Hazard
Posts: 1326
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
I've used a MAPP torch to soften and fuse borosilicate successfully.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
|
Gargamel
Hazard to Others
Posts: 166
Registered: 9-3-2013
Member Is Offline
Mood: No Mood
|
|
Thank you for the input 
Glassrod it shall be.... Lets see what I can shop...
|
|
|
Oxy
Hazard to Others
Posts: 140
Registered: 1-12-2020
Member Is Offline
|
|
I am using a sealed glass Pasteur pipette. It's torched on one side, on the bottom I put a tiny amount of silicon oil (for better heat transfer).
On the other side it's protected by electrical tape. This is very easy to setup with any lab burner and Pasteur pipette fits the thermometer adapter.
|
|
|
CharlieA
National Hazard
Posts: 646
Registered: 11-8-2015
Location: Missouri, USA
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Oxy  | I am using a sealed glass Pasteur pipette. It's torched on one side, on the bottom I put a tiny amount of silicon oil (for better heat transfer).
On the other side it's protected by electrical tape. This is very easy to setup with any lab burner and Pasteur pipette fits the thermometer adapter.
|
Shade tree engineering in the chemistry lab! I love it!
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
