mackolol
Hazard to Others
Posts: 459
Registered: 26-10-2017
Member Is Offline
Mood: Funky
|
|
very viscous styrene
Hi,
Recently I have purchased some styrene. It smells just like I would imagine: styrofoam after heating, it reacts with chlorine and bromine foming
solid...
What boggles me though is its enormously high viscosity. I expected mobile liquid (I'm even pretty sure styrene is a mobile liquid) and instead got
super thicc, syrupy liquid.
I would compare it to anhydrous glycerol!
Also, it's completely colorless, even after a month of storage after being opened.
Can it be polymerisation? Rather unlikely, because it's still completely colorless. Maybe it's stabilised with something that makes it this way?
Can anyone give me some hint?
|
|
|
numos
Hazard to Others
Posts: 269
Registered: 22-2-2014
Location: Pasadena
Member Is Offline
Mood: No Mood
|
|
This sounds like polymerization to me.
Styrene doesn't keep long, a few years at -20 C, less than a year at room temperature if not stabilized. Polymerization to polystyrene wouldn't impart
any color so the fact that it's colorless might not mean much. Styrene is one of those chemicals that you kind of need to distill directly before use
anyways, so I suggest to distill a small amount and see if you can get anything less viscous out of it.
Just to note, pure styrene is viscous too, not like glycerol, but still viscous. Stabilizers are most likely small amounts of radical traps and would
not affect viscosity.
|
|
|
UC235
National Hazard
Posts: 565
Registered: 28-12-2014
Member Is Offline
Mood: No Mood
|
|
Pure styrene is actually less viscous than water. Fortunately, styrene can be partly recovered by distillation. Very polymerized material could be
destructively distilled followed by fractionation of the initial distillate which contains a fair amount of oligomeric material. The same process can
be used to make styrene from solid polystyrene plastic
|
|
|
mackolol
Hazard to Others
Posts: 459
Registered: 26-10-2017
Member Is Offline
Mood: Funky
|
|
That's what I wanted to avoid :/ . There's going to be a lot of crap, carcinogenic and hard to remove...
|
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Styrene is carcinogenic (though not strongly so).
Most of the material should distil . What will be left is essentially polystyrene (which is practically non- toxic) and a bit of "charred" stuff.
There are plenty of solvents that will remove the polymer- I guess ethyl acetate is probably the least toxic.
You will probably end up scrubbing the char out mechanically unless you are prepared to use something like hot sulphuric acid.
|
|
|
Keras
National Hazard
Posts: 929
Registered: 20-8-2018
Location: (48, 2)
Member Is Offline
|
|
You can stabilise styrene using hydroquinone or BHT
|
|
|
karlos³
International Hazard
Posts: 1520
Registered: 10-1-2011
Location: yes!
Member Is Offline
Mood: oxazolidinic 8)
|
|
Stabilised monostyrene keeps quite well, bought mine 4-5 years ago and its still waterlike from the viscosity.
The key for me(at least thats what I want to believe  ) is, directly after
receiving the stuff in a can, to bottle it up and to put it in several bottles, a small one for "regular" use, and larger ones for storage.... I
actually have opened the large bottles only 5 times over all the years since I bottled it up.
What speaks for the still surpreme quality, the styrene could be as it is, undistilled even directly from the bottle, be turned via bromohydrin(NBS),
base to the epoxide, followed by ammonolysis with 2-amino-2-methylpropanol/isobutanolamine, be turned into crude base with 49,xx% and after oxalate
salt formation, still after some losses, over 41,xx% yield, and that is based on the raw, undistilled alkene!
When I tried the same with methylamine, it did not work that well(in yield) or clean(unlike the same product made from acetophenone) yet, and the
ethylamine trial I still need to work up.
The styrene is still quite good though, after all these years, water like from its viscousity.
Although I did notice some needle like crystals when pouring some styrene into a beaker, and adding solvent to wash it out, at that point suddenly
some large needles will become visible(and audible, making *pling* sounds due to the size ).
Seems like they had a few years to grow in there 
Its not much though, but it is noticeable, I haven't weighed them, but it was like ~500mg's at most the last time I measured 24g of styrene out.
verrückt und wissenschaftlich
|
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
"Although I did notice some needle like crystals "
Any idea what they were?
|
|
|
mackolol
Hazard to Others
Posts: 459
Registered: 26-10-2017
Member Is Offline
Mood: Funky
|
|
They were probably polymerised stuff. I notice similar behavior in my styrene. Especially when I chlorinate it. Then on addition of acetone or
methanol, there comes out white plasticky goo that sticks to everything and reminds me of nylon from NileRed's videos...
Anyways, what I have done was distillation of my styrene and as you all might expect that was enough. I was left with transparent goo in my flask,
which was removed by refluxing few times with toluene (resulting in similar solution I started with, but this time instead of styrene, toluene was the
solvent).
Didn't bother to destructively distill that using burner, only tried to with my 500C cheap hotplate and although I've read that polystyrene decomposes
at 350C with base catalyst, the decomposition rate with potassium carbonate was negligible in that temp (the stuff got slightly brown).
Well that's interesting what you tell me Karlos , I must have gotten some really old or unproperly handled shit...
|
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Polystyrene dissolves in styrene, so it can't be the crystals.
|
|
|
mackolol
Hazard to Others
Posts: 459
Registered: 26-10-2017
Member Is Offline
Mood: Funky
|
|
Quote: Originally posted by karlos³  |
Although I did notice some needle like crystals when pouring some styrene into a beaker, and adding solvent to wash it out, at that
point suddenly some large needles will become visible(and audible, making *pling* sounds due to the size ).
|
Probably some polar one for example the ones I have mentioned.
|
|
|
karlos³
International Hazard
Posts: 1520
Registered: 10-1-2011
Location: yes!
Member Is Offline
Mood: oxazolidinic 8)
|
|
Does DMSO dissolve polystyrene too, though?
Because they only precipitated on addition of DMSO from the styrene.
Or was it after I washed the beaker with water?
Hmm.
I'll pay attention next time.
E: oh! My notes do say it was DMSO containing around ~10% of H2O which I used to rinse the beaker!
Because that was alsoo the reaction solvent used there.
That would explain the precipitated crystals much more than plain DMSO would have.
@mackolol soon going to check back in home... course of the next week at last, I have so, so many interesting things to report about 
[Edited on 3-4-2022 by karlos³]
verrückt und wissenschaftlich
|
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
I have never seen crystalline polystyrene, so I'm still puzzled.
|
|
|
Triflic Acid
Hazard to Others
Posts: 486
Registered: 27-9-2020
Member Is Offline
Mood: Slowly Oxidizing into Oblivion
|
|
Polymerized styrene can form hard clear chunks that might look like crystals, sending photos would help tell the difference.
There wasn't a fire, we just had an uncontrolled rapid oxidation event at the power plant.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
