LD5050
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 182
Registered: 16-1-2017
Member Is Offline
Mood: No Mood
|
|
Dimethylamine identification help
I made dimethylamine using this procedure I found on a quick search through google:
To 75 g (1.03 mol) of dimethylformamide in a 500 ml roundbottom flask was slowly added, portionwise, 160 g 6N aqueous hydrochloric acid. Caution, this
was a very exothermic process! The flask was fit with a condensor and the mixture was refluxed for 7 hours. Dimethylformamide hydrolyses to
dimethylamine and formic acid, so the fumes were led outside in case some carbon monoxide formed due to decomposition of HCOOH.
The mixture was vacuum distilled at the fridge pump until a white mushy solid was left in the distilling flask. This was sucked as dry as possible on
a Buchner funnel and transferred to a dessicator, where it was dried over CaCl2 for a couple of days. There was obtained 59.3 grams of dimethylamine
hydrochloride as sparkling white crystals, which is a yield of 70% .
Everything went according as planned. I ended up with a white crytally powder that was VERY hygroscopic. I recrystalized from MeOH and long needle
like white transparent crystals formed. The literature claims dimethylamine HCL melting point is 168-176c. I performed a crude melting point test by
adding some crystals to a test tube throwing in a thermometer and placing on my hot plate. I got a M.P. Of around 140-150c which is quite low even for
my makeshift M.P. Apparatus.
I'm wondering if there is any other tests I can perform to positively identify that what I have is infact Dimethylamine. Searching on google I can't
find much on solubility and other properties of dimethylamine. Any help or information on this would be really appreciated thanks.
|
|
UC235
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 565
Registered: 28-12-2014
Member Is Offline
Mood: No Mood
|
|
Unless you didn't start with DMF, what you have is Dimethylamine HCl. Sounds like a combination of your terrible melting point determination and
possible water contamination, which can dramatically depress melting point of hygroscopic salts. Try using a stirred beaker of mineral oil to slowly
heat the thermometer and sample side by side.
|
|
alking
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 252
Registered: 11-3-2016
Member Is Offline
Mood: No Mood
|
|
What he said. 150C is pretty close imo under the circumstances, it's highly unlikely you have anything else just based on the fact that you yielded a
crystaline product at all. Combine that with the description and seeming uniformity of the crystals, their hygroscopic nature, and the mp I'd say it's
all but confirmed.
|
|
Melgar
Anti-Spam Agent
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
Also, you don't have to worry about formic acid producing carbon monoxide unless you're adding it to a very strong dehydrating agent. The only ones I
know for sure will do it are P2O5 and H2SO4. The more energetically favorable decomposition is to CO2 and H2, which palladium catalyzes, for example.
And of course, any oxidizers will yield either performic acid or carbonic acid (and then probably rearrange to H2O and CO2).
The first step in the process of learning something is admitting that you don't know it already.
I'm givin' the spam shields max power at full warp, but they just dinna have the power! We're gonna have to evacuate to new forum software!
|
|
AvBaeyer
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 647
Registered: 25-2-2014
Location: CA
Member Is Offline
Mood: No Mood
|
|
I have made dimethylamine hydrochloride by the OP route many times. The crystalline product is extremely difficult to dry completely. Calcium chloride
is not good enough. I dried my product in a dessicator using both NaOH and H2SO4 (separate containers, of course!) as drying agents. This works quite
well but the time it takes depends on how much water is in the initial product.
AvB
|
|
LD5050
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 182
Registered: 16-1-2017
Member Is Offline
Mood: No Mood
|
|
Ya I can't believe how much this stuff likes to suck up water from the air, I mean it's almost instantaneous. I dried mine pretty well by just puting
it in a glass bowl with an air tight lid with a little cup full of silica beads inside.
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7998
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
I have dimethylformamide. I read about synthesis of dimethylamine with that, using HCl and heating for several hours, to get a solution of
dimethylammonioum chloride. This seems to be very hard to purify and dry. This thread also demonstrates that.
Why not add an excess amount of a concentrated solution of KOH or NaOH to the DMF and heat this? I tried this on a small scale and it seems to me that
this works very easily. The solution quickly starts bubbling and a lot of gas is produced. From 2 ml of dimethylformamide, I could maintain a flame
for several minutes, using this method. I did not collect the gas in water for this test, I just wanted to see whether it produces dimethylamine
easily in a steady flow of gas. The gas has a strong ammonia-like smell, albeit a little less pungent, and at lower concentration it has an added
smell of stale piss as well. I burned the gas at the end of a glass pasteur pipette, just to avoid having the smell of the gas all around the house.
This almost certainly must be dimethylamine.
Why is this method not used? It looks much simpler to me than the hassle with the extremely hygroscopic dimethylammoium chloride. Simply lead the gas
through a large column of ice cold water to get it dissolved. Does this reaction with NaOH or KOH produce a lot of side-products, which also escape as
gas and make the product impure?
I also can obtain N-methylformamide (this has only one methyl group) for a fairly low price. Can this equally easily be used to make monomethylamine
gas with NaOH or KOH?
[Edited on 10-1-22 by woelen]
|
|
karlos³
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1520
Registered: 10-1-2011
Location: yes!
Member Is Offline
Mood: oxazolidinic 8)
|
|
I made dimethylamine both with acidic and basic hydrolysis, I preferred the basic one after a while.
The acidic actually can produce an almost dry salt if you quickly store it away, in fact I was surprised I had a few years old slightly mushy bottle
of dimethylamine HCl made that way.
Carbon monoxide gets produced though.
The yields are fine for both methods, more or less in the same range of around 70%, but one involes hours of heating and the other an hour or two of
closely monitored, well focused on, gassing.
Depends on personal preferences, I guess.
I actually did it in three single gassing episodes when I made a half mol of dimethylamine in ethanol, because it was so annoyingly slow and I really
did not wanted to ruin it or gass everything except the solvent with the amine.
It does not smell much at all, though, that was great.
But I used ice cold solvent directly from the freezer, standing in an ice bath.
woelen, yes, N-methylformamide can be used for the production of methylamine and in fact I believe that OP already did this a year or two after
starting this thead.
By the way, I wonder if dimethylamine oxalate would be a nicely isolateable salt is, dry and not hygroscopic...?
verrückt und wissenschaftlich
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7998
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
I think, I prefer the basic route. The material does have a smell for me, but I do not perceive it as that bad as some people make you believe it is.
Quite smelly, but I know more nausiating smells.
I wonder, why the yield only is 70%, especially in the basic route. If excess NaOH is used, don't you simply drive off all dimethylamine and keep
formiate ions in solution? Or is there some side-reaction, in which 30% goes, forming non-gaseous products, which remain in solution?
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7998
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
I now also have N-methylformamide and compared that to N,N-dimethylformamide.
N-methylformamide has a faint sweet smell, N,N-dimethylformamide has no smell at all (maybe a slight pissy smell, due to impurity of dimethylamine).
I mixed both chemicals with a concentrated solution of NaOH (appr. 2 ml of liquid, mixed with 3 ml of concentred lye).
- N,N-dimethylformamide requires gentle heating to produce gaseous dimethylamine. The reaction is quite smooth.
- N-methylformamide decomposes even without heating. Small bubbles of methylamine are produced. Gently heating makes the reaction faster and quite a
strong flow of methylamine can be produced with just gentle heating.
So, now I can make both methylamine and dimethylamine easily. The only thing I still do not know is why the yield would only be 70% for this type of
reaction, as mentioned in previous posts. Is this really true? I would expect the reaction to have a yield of nearly 100%, albeit that at the end the
reaction probably slows down.
I also noticed that dimethylamine and methylamine have very similar smells at higher concentrations. These gases are not as pungent as ammonia, but
still quite irritating at higher concentrations and having an ammonia-like smell. At low concentrations, I perceive a difference in smell.
Dimethylamine smells like stale piss, while methylamine has a more fishy smell. I do not perceive the smell of these gases as really nauseating, but
having these smells around your house is not what you want. So, making larger quantities of the gases and dissolving it in water requires some care,
to avoid having the neighbourhood smell of piss or decaying fish.
[Edited on 24-3-22 by woelen]
|
|