| Pages:
1
2 |
SuperOxide
Hazard to Others
Posts: 487
Registered: 24-7-2019
Location: Devils Anus
Member Is Offline
|
|
Attaching 24/40 glassware joints to non-jointed flasks
My largest jointed flask is a 24/40 2L erlenmeyer flask, and I love this thing. I like using it for any reactions that have large reaction mixtures
yet low returns (aniline, toluidine, benzyl chloride, etc). I don't have anything larger than 2L, but if I wanted to get something larger, I might
have to settle for something without a ground glass joint (since I'm mostly looking for stuff from domestic ebay sellers).
Most of the erlenmeyer flasks can use #10 rubber bungs which I could drill a hole in or even buy them pre-drilled (like this one). But usually the holes are only wide enough to accept a thin tube or something, not quite wide enough for a 24/40 or even just 14/20
joint.
I was curious if anyone here has a solution that might be a little more sturdy? I can't help but think that attaching a 24/40 condenser via a rubber
bung might be a little sketchy. But I could be wrong.
If anyone has done this and has pics, please share :-D
|
|
|
Belowzero
Hazard to Others
Posts: 173
Registered: 6-5-2020
Location: Member Is Offline
Member Is Offline
|
|
In this case I use large rubber stoppers, brewery supply stores sell these, at least around here.
The stoppers have a slight angle which allows them to fit various sized flasks.
They stoppers come with or without holes.
A regular wood drill is quite effective for drilling those.
I have a couple lying around which have a glass tube fixed in the hole which has the correct diameter for fitting rubber hoses.
The disposable glass pipets I have are the perfect diameter and are quite capable of handling heat.
Easy and cheap solution.
Another solution would be to drill a large hole and fit a ground glass adapter in the stopper and work from there.
[Edited on 26-11-2021 by Belowzero]
|
|
|
Sulaiman
International Hazard
Posts: 3722
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
A direct glass-to-metal joint is difficult due to differences in thermal expansion rates,
So some type of rubber or plastic is required,
rubbers and plastics are often incompatible with various chemicals and/or high temperatures.
So it depends upon what you intend to do.
Various members have at various times offered to make and sell ptfe bulkhead-to-ground glass joint adapters,
but I've not seen any finished products.
One option is to fit a metal tube to the metal vessel
and a gas adapter to the glassware,
with suitable tubing between the two (pvc, silicone, ptfe etc.)
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
macckone
Dispenser of practical lab wisdom
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
There are rubber and silicone vacuum filtration adapters.
Rubber:
https://www.amazon.com/Filter-Adapter-Buchner-Funnel-Tapered...
Silicone:
https://www.amazon.com/Rainbowrock-Adapter-Cone-Silicone-Sto...
You can also buy various polymer kits to make your own.
And of course you can use teflon tape either by itself or to wrap rubber, cork or silicone with.
And last you can use kapton film, also sold as roasting bags for turkeys.
|
|
|
macckone
Dispenser of practical lab wisdom
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
A side note, this depends on how air tight you need it to be.
I have a high heat fused quartz rig that I interface with a regular condenser but
I use fiberglass rope for the seal. I use it for distilling H2SO4.
The fiberglass rope isn't 'air tight' but it does keep the H2SO4 on the inside.
Note this is a transition from an air condenser to a water condenser so there isn't a lot of vapor.
For the OP use I would say something made of or covered in teflon is going to work better.
If using metal containers and needing an air tight seal, I use exhaust system sealing putty.
It will eventually crack but it is cheap enough for single use applications.
The wrap it with teflon tape trick is useful at temperatures below 200C.
You can wrap a rubber stopper in teflon tape and it effectively becomes a teflon stopper.
|
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Quote: Originally posted by Sulaiman  | A
Various members have at various times offered to make and sell ptfe bulkhead-to-ground glass joint adapters,
but I've not seen any finished products.
|
That's bcoz of the Teflon porn curse. Anyone advertising Teflon adaptors
and posting pictures disappears never to be heard from again.
[Edited on 27-11-2021 by draculic acid69]
|
|
|
Sulaiman
International Hazard
Posts: 3722
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Just remembered :
I have two sizes of ptfe adapter for overhead stirring, a 24/29 for my diy overhead stirrer,
and my 19/23 was advertised as a thermometer holder - which is actually what I use it for.
Either can grip 7mm od borosilicate tubing, and seal into round holes.
|
|
|
SuperOxide
Hazard to Others
Posts: 487
Registered: 24-7-2019
Location: Devils Anus
Member Is Offline
|
|
So I actually forgot I had those, and I use them for vacuum filtrations, and they work well (I've only ever had like 2 in use at a time, max). But
this is more for things like refluxing, not even distillations.
| Quote: Originally posted by macckone | A side note, this depends on how air tight you need it to be.
I have a high heat fused quartz rig that I interface with a regular condenser but
I use fiberglass rope for the seal. I use it for distilling H2SO4.
The fiberglass rope isn't 'air tight' but it does keep the H2SO4 on the inside.
Note this is a transition from an air condenser to a water condenser so there isn't a lot of vapor.
For the OP use I would say something made of or covered in teflon is going to work better.
If using metal containers and needing an air tight seal, I use exhaust system sealing putty.
It will eventually crack but it is cheap enough for single use applications.
The wrap it with teflon tape trick is useful at temperatures below 200C.
You can wrap a rubber stopper in teflon tape and it effectively becomes a teflon stopper.
|
The only time I plan on using this is for reactions that have a large volume but a relatively small return (think aniline, toluidine, benzyl chloride,
etc). So I would use this for the reflux part, then I could separate off the desired layer, and bring that to a much smaller flask (probably 1L).
| Quote: Originally posted by Sulaiman | Just remembered :
I have two sizes of ptfe adapter for overhead stirring, a 24/29 for my diy overhead stirrer,
and my 19/23 was advertised as a thermometer holder - which is actually what I use it for.
Either can grip 7mm od borosilicate tubing, and seal into round holes. |
Interesting. I know I could get a female 24/40 for the male end of the condenser, and bring that down to a small diameter that would fit in a rubber
bung with a small hole in it, but I wasn't sure how well refluxing such a large volume through a small hole.
Do you have pics?
|
|
|
SWIM
National Hazard
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
Just for context, how big a flask are we talking about here?
Refluxing several liters of something through a little tube may lead to solvent 'spitting' out the top of your condenser, or possibly the 24/40
condenser just filling up with solvent and overflowing.
As Belowzero said, those rubber stoppers are easy to drill out.
And, somewhat ironically, below zero is a good temperature to have your stopper at when you drill it. Leave it in the freezer overnight.
I'd try drilling one out to 7/8 inch. That ought to fit okay for a 24/40 joint. You can taper the top of the hole a bit by wrapping sandpaper around
the 24/40 male joint and sticking it in there and working it around if you need to.
Start with a single hole stopper and you've got a pilot hole that'll help ensure a straight, true and centered hole.
[Edited on 28-11-2021 by SWIM]
|
|
|
Organikum
resurrected
Posts: 2339
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: frustrated
|
|
Drilling holes into rubber stoppers was always a major pain in the ass and I never achieved the results I hoped for. But I found happiness with good
ol' cork which is easy to work with and I found out that when I wrap the cork stopper through the hole with the better quality PTFE tape (12 mm wide
and thicker and denser then the usual one) then I end up with a durable reusable connector which is IMHO far superior to rubber or silicone. After
several uses it will have some discoloration and I just wrapped another layer on top and in the longer run I had some cork filled PTFE stoppers with
holes for grounded joints. Neat! The PTFE compresses und by pressure und heat it gets kind of sintered (PTFEs usually bad habit of giving in to "cold
flow" comes out as a bonus here).
I also like the lower weight of those stoppers compared to Rubber or solid PTFE. It would be something worth to commercialize - There is a market if
the price is reasonable, I am sure.
I tried a lot, this was the best.
/ORG
|
|
|
SuperOxide
Hazard to Others
Posts: 487
Registered: 24-7-2019
Location: Devils Anus
Member Is Offline
|
|
Well, I just ordered a 4L Pyrex flask,
supposedly new, from ebay (for $65 shipped! I have my suspicions - But even if its fake, it may still be useful). But in a 4L flask, I will probably
never fill it past 2 or 2.5L. It accepts a #10 stopper.
| Quote: Originally posted by SWIM | | Refluxing several liters of something through a little tube may lead to solvent 'spitting' out the top of your condenser, or possibly the 24/40
condenser just filling up with solvent and overflowing. |
That's exactly what I was worried about. I don't think it makes sense to even try, lol.
| Quote: Originally posted by SWIM | As Belowzero said, those rubber stoppers are easy to drill out.
And, somewhat ironically, below zero is a good temperature to have your stopper at when you drill it. Leave it in the freezer overnight.
|
That's some great advice.
| Quote: Originally posted by SWIM | I'd try drilling one out to 7/8 inch. That ought to fit okay for a 24/40 joint. You can taper the top of the hole a bit by wrapping sandpaper around
the 24/40 male joint and sticking it in there and working it around if you need to.
Start with a single hole stopper and you've got a pilot hole that'll help ensure a straight, true and centered hole. |
The sandpaper around the joint is a great idea as well. I will definitely give that a shot. I just ordered these, and I may try drilling it out wider then sanding it to see if I can directly place a 24/40 in there, if not, maybe I can squeeze in a 14/20
adapter.
[Edited on 28-11-2021 by SuperOxide]
|
|
|
SuperOxide
Hazard to Others
Posts: 487
Registered: 24-7-2019
Location: Devils Anus
Member Is Offline
|
|
So I got the Erlenmeyer flask in today, and the tapered collar set I already have actually works great. I didn't think it would because it just seems
like it would leak. I usually use it for vacuum filtrations and the vacuum pressure makes it seal well, but it worked well here too.
 
I tested it with boiling 2L of water, and while that's not a big deal, I did crank the hotplate up to 300 °C right off the bat, and it held up to the
immediate temperature change very well. This was a fricken steal for $65 bucks (off ebay). I recommend it to anyone that thinks they will ever need a flask this big.
|
|
|
macckone
Dispenser of practical lab wisdom
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
That is a good deal on the flask.
|
|
|
SuperOxide
Hazard to Others
Posts: 487
Registered: 24-7-2019
Location: Devils Anus
Member Is Offline
|
|
Hell yeah it is. I was hesitant to link to it because it would feel like I was pushing it or like I was paid to say it, lol. But I think if anyone
needs one, these deals would be very useful.
Im honestly kinda tempted to get a 2nd one. Not because I need it, but in case I break this one. I don't think ill ever find a deal this decent again.
[Edited on 4-12-2021 by SuperOxide]
|
|
|
brubei
Hazard to Others
Posts: 188
Registered: 8-3-2015
Location: France
Member Is Offline
Mood: No Mood
|
|
I use champagne corks. Their conical or round shape makes them easy to insert or remove on a neck. You can easily make clean holes inside with a
drill.
I'm French so excuse my language
|
|
|
SuperOxide
Hazard to Others
Posts: 487
Registered: 24-7-2019
Location: Devils Anus
Member Is Offline
|
|
| Quote: Originally posted by brubei | | I use champagne corks. Their conical or round shape makes them easy to insert or remove on a neck. You can easily make clean holes inside with a
drill. |
Do they have champagne corks this large? That would be one hell of a champagne bottle, lol.
But I think the typical cork material (made from bark I believe) isn't inert enough for some things I use in the lab.
|
|
|
macckone
Dispenser of practical lab wisdom
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
Superoxide,
You can buy corks pretty big and you can get cork blocks.
See the comments on covering the stopper with teflon plumbers tape.
The tape will melt at around 320C forming a solid layer, using a heat gun will prevent the cork from decomposing.
|
|
|
SuperOxide
Hazard to Others
Posts: 487
Registered: 24-7-2019
Location: Devils Anus
Member Is Offline
|
|
| Quote: Originally posted by macckone | Superoxide,
You can buy corks pretty big and you can get cork blocks.
See the comments on covering the stopper with teflon plumbers tape.
The tape will melt at around 320C forming a solid layer, using a heat gun will prevent the cork from decomposing. |
That's pretty interesting.
However, I think I might have found an even better solution. It occurred to me that I have a 24/40 to 45/55 adapter for my soxhlet extractor, and that
#10 neck looked like it would be a close fit for it...
And, well... ill be damned. It fits pretty damn well.
Honestly, it makes a decent seal even without any grease or teflon tape, but just in case, a quick wrap or two of teflon tape and it makes a perfect
seal.
It's actually very surprising how perfectly that fits, lol.
|
|
|
crow6283
Hazard to Self
Posts: 60
Registered: 14-1-2018
Member Is Offline
Mood: No Mood
|
|
Do a quick search for a “cork borer”, this is a common tool you would see in a brick and mortar lab supply store, but if left to your own devices
online maybe wouldn’t even know it exists! The common ones sold only go up to maybe 12 or 16 mm in diameter, but once you’ve got a hole that big
you can use a Dremel to grind it bigger to the size you need. Alternatively, you can make your own larger sized cork borer if you have say a bit of
appropriately diametered copper tube and a grinder to grind a bit of an edge on it, or you can simply heat the end up with a torch and it will melt
through the rubber! I have used connections made like this (from a male ground joint, wrapped in small amount of rubber stopper stopper, to a female
heavy walled flask) even for vacuum distillations (not high vacuum, just with an aspirator) in a pinch and it worked just fine, although it of course
is not recommended.
-edit- should also be noted that not all rubber stoppers are created equally. The white ones used for fermenting I would not recommend for heating
anything, and I’m also not sure how they would react to various organic compounds. The stoppers sold for lab use come in different colors. The
green I believe are more resistant to acids and bases. Best to prepare a few for what you are doing and toss them after a while, after repeated use
and exposure they have a tendency to harden and crack.
[Edited on 7-12-2021 by crow6283]
|
|
|
macckone
Dispenser of practical lab wisdom
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
Given that it is tapered and the neck is not, as long as the big end is bigger and the small end is smaller on the tapered piece, it should fit pretty
well if the neck is round. If it isn't round just add more teflon tape on that side.
|
|
|
SuperOxide
Hazard to Others
Posts: 487
Registered: 24-7-2019
Location: Devils Anus
Member Is Offline
|
|
| Quote: Originally posted by macckone | | Given that it is tapered and the neck is not, as long as the big end is bigger and the small end is smaller on the tapered piece, it should fit pretty
well if the neck is round. If it isn't round just add more teflon tape on that side. |
It does fit, almost like it was meant to fit there. Damn near perfect, lol. I recon I could even get it to form a seal with just some grease, but I'll
use a layer (or two) of teflon tape instead, just to be safe.
|
|
|
violet sin
International Hazard
Posts: 1482
Registered: 2-9-2012
Location: Daydreaming of uraninite...
Member Is Offline
Mood: Good
|
|
@ crow6283
I agree. You can certainly sharpen the OD of a piece of copper tube by relieving it of the ID edge with a file. It can then be stuck in a drill
press or hand drill to make holes in thing that don't like to cut nicely.
I've used it on cork and solid silicone caulk. If you've ever had a tube that was found to be old and solid... Free the slug of solid material, cut
to length and bore out.
It doesn't do much at first but the friction builds and it will suddenly sink in the surface and then slowly progress further. I've not made them
bigger than half inch, but larger pipe could be used on a smaller shaft to fit the motored device what ever it be.
You don't have to run out any buy everything if you've some tools and an hour or so free time. I'm good at building things so that helps. Only way
to get better is keep building, so level up.
Edit: I butchered your screen name, then fixed it, sorry.
[Edited on 11-12-2021 by violet sin]
|
|
|
SWIM
National Hazard
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
That does look like a good fit.
Good thing you bought a Quality flask.
Some cheap modern Erlenmeyers can be lumpy or out of round at the top, but major manufacturers usually have nice even beads on their flasks.
Given the option I'll go for used equipment from a major manufacturer before new stuff from somebody I've never heard of for just this reason.
[Edited on 11-12-2021 by SWIM]
|
|
|
SuperOxide
Hazard to Others
Posts: 487
Registered: 24-7-2019
Location: Devils Anus
Member Is Offline
|
|
| Quote: Originally posted by SWIM | | Given the option I'll go for used equipment from a major manufacturer before new stuff from somebody I've never heard of for just this reason.
|
I couldn't agree more. All my favorite glassware is the used stuff from Ebay (Mostly from BiotectCT or BiotectCA, amazing prices). I get all the best
brands for very affordable prices.
I wish I realized this earlier, lol. I have so many crappy pieces of glassware that I don't use because of how bad quality they are (eg: super thin
walls or bad fitting joints).
|
|
|
Fyndium
International Hazard
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
I have a couple of ground joints that are slightly asymmetric and leak under vacuum. A noticeable bubble trail can be observed when applying. I
decommissioned these joints, one which was thermowell, not only because they leaked, although a powerful pump could overrun the leak easily, but
because they can cause uneven stress distribution to glass, which can be catastrophic danger in vacuum work.
|
|
|
| Pages:
1
2 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
