CycloRook
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 89
Registered: 2-4-2018
Member Is Offline
Mood: No Mood
|
|
Vacuum pump for distillation etc.
I have a rotary vane pump that is used for refrigerant replacement.
This is a basic pump and pulls a 50 micron vacuum.
I have an issue with it. The suction is great it's just that the exhaust end has an oil and noise dampener but absolutely no way of channeling the
exhaust. This is almost useless for anything other than water distillation as I would be essentially pumping whatever is in my glassware to my
workspace. I don't have a fumehood.
A solution would be to get an inline blower and position it next to the exhaust port.
Ideally I would like to just take 3/4 tubing and rout it out the window.
If you need more pictures just let me know.
Thanks
|
|
arkoma
Redneck Overlord
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1761
Registered: 3-2-2014
Location: On a Big Blue Marble hurtling through space
Member Is Offline
Mood: украї́нська
|
|
I'm not home so can't take a pic, but my Robin air exhausted through the carrying handle. I unscrewed it, screwed in a barbed hose adapter, clobbered
up an oil trap and then continued on with an exhaust house ran through the wall to the outside. Presto.
"We believe the knowledge and cultural heritage of mankind should be accessible to all people around the world, regardless of their wealth, social
status, nationality, citizenship, etc" z-lib
|
|
CycloRook
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 89
Registered: 2-4-2018
Member Is Offline
Mood: No Mood
|
|
I'm thinking to do the same thing. When I take this cap of the pump is very loud. I'm thinking to find some kind of barbed adapter but trying to match
threads sounds hard.
|
|
BromicAcid
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3237
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
You could also make sure you put good traps inline before the pump and then locate it remotely outside your work area.
|
|
zerodan
Harmless
Posts: 27
Registered: 4-4-2019
Member Is Offline
|
|
Quote: Originally posted by cycloknight19 ![](images/xpblue/lastpost.gif) | I have a rotary vane pump that is used for refrigerant replacement.
This is a basic pump and pulls a 50 micron vacuum.
I have an issue with it. The suction is great it's just that the exhaust end has an oil and noise dampener but absolutely no way of channeling the
exhaust. This is almost useless for anything other than water distillation as I would be essentially pumping whatever is in my glassware to my
workspace. I don't have a fumehood.
A solution would be to get an inline blower and position it next to the exhaust port.
Ideally I would like to just take 3/4 tubing and rout it out the window.
If you need more pictures just let me know.
Thanks |
Looks like the standard model. How much did you pay for it?
I have a similar pump and mine exhausts through the oil refiling cap.
Does your pump also produce a white mist when running?
I tried to remedy that by 3D printing the oil cap with a plastic mesh in the middle where I could place cotton to filter the exhaust. Third time was
the charm and the threads were a good enough fit, so if you have a 3D printer you can try printing a hose adapter for the exhaust.
|
|
CycloRook
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 89
Registered: 2-4-2018
Member Is Offline
Mood: No Mood
|
|
No white mist. It's completely clean. Maybe if I sit in the plumbing department I'll find something
|
|
arkoma
Redneck Overlord
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1761
Registered: 3-2-2014
Location: On a Big Blue Marble hurtling through space
Member Is Offline
Mood: украї́нська
|
|
the carrying handle on my Robinair was standard US NPT 1/2" i believe. take the cap with you to the plumbing department with you, and find out what it
screws into and you have the thread size figured out.
Again, not home so no pics, but i was gifted an old hospital vacuum receiver jar (guess that what you'd call it) that i have in the suction line
before the pump. Its size of a gallon pickle jar with a metal screw lid. the line coming IN to the jar I extended to bottom of jar with tubing and I
keep a pretty good layer of dry epsom in the bottom; best i can do at the moment for a moisture trap. I usually change the oil about every use too,
and cheat and use power steering fluid. Also, in the interest of safety, the jar is in a deep metal drawer of my desk/lab bench that I keep closed as
far as I canto contain flying shards of glass in case of an implosion. Pulled 28 inches on it many an occasion.
"We believe the knowledge and cultural heritage of mankind should be accessible to all people around the world, regardless of their wealth, social
status, nationality, citizenship, etc" z-lib
|
|
CycloRook
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 89
Registered: 2-4-2018
Member Is Offline
Mood: No Mood
|
|
Ok. I might as well document my findings as it may help others.
Tomorrow I'll go to the hardware store.
|
|
CycloRook
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 89
Registered: 2-4-2018
Member Is Offline
Mood: No Mood
|
|
Well the hardware store doesn't have the size I need. The size of the hole is 3/4 but the threads are finer than regular pipe threads
|
|
CycloRook
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 89
Registered: 2-4-2018
Member Is Offline
Mood: No Mood
|
|
Would anyone happen to know what thread size is finer than NPT ?
|
|
macckone
Dispenser of practical lab wisdom
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
There are imperial fine threads which aren't normally used on pipe fittings and metric which is generally a finer thread than NPT.
You may want to pick up a thread guage.
|
|
arkoma
Redneck Overlord
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1761
Registered: 3-2-2014
Location: On a Big Blue Marble hurtling through space
Member Is Offline
Mood: украї́нська
|
|
Are they tapered? I also didn'y look, but if the pump is European, most likely metric. If you live in a big enough city, there will be people that
sell just bolts.
*Brain Storm*--in the spec sheet for the product should be listed. Probably looking for something in neighborhood of M14 X 1.0 Diameter in mm, and
pitch in thread per mm. Also, a machine shop should be able to identify the thread quickly
"We believe the knowledge and cultural heritage of mankind should be accessible to all people around the world, regardless of their wealth, social
status, nationality, citizenship, etc" z-lib
|
|
chemrox
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
Quote: Originally posted by BromicAcid ![](images/xpblue/lastpost.gif) | You could also make sure you put good traps inline before the pump and then locate it remotely outside your work area. |
Yes! I don't know what you need to trap but use a trap for two reasons; avoiding vapor in your space and keeping your oil clean. I used acetone and
dry ice for my traps. Also, since ventilation seems to be an issue make sure you don't get CO2 narcosis (hypercapnia). Another thing to consider is an
aspirator pump. You would get a better result than using a simple aspirator. I used one with my rotary evaporators and it worked well for most
solvents. Sometimes the addition of ice to the bath helped and although I kept a fresh water flow going through it the water use was much lower than
a conventional aspirator. In fact my set up was running the water from the condenser through the pump reservoir
"When you let the dumbasses vote you end up with populism followed by autocracy and getting back is a bitch." Plato (sort of)
|
|
Ubya
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
What kind of pump oil are you using?
Usually vacuum pump oils are sensitive to moisture, so even normal water distillations can harm them and the pump.
I ended up making a closed loop water aspirator for this reason, so i can use my crappy rotary vane pump for less destructive projects
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|