RustyShackleford
Hazard to Others
Posts: 200
Registered: 10-12-2020
Location: Northern Europe
Member Is Offline
|
|
Setups for burning liquid form aromatic waste
Im looking for a nice way of burning small to medium amounts of aromatic waste, 10-100ml type amounts. My usual go to method is to use a normal oil
candle type setup, but the problem with this is obviously that it creates a large amount of soot unless the wick is set absolutely perfectly, and even
then its stinky and produces soot.
Does anyone know of or has built a device that is able to burn solvents such as toluene and xylene without creating much soot or unoxidized
hydrocarbons?
The idea i got was to pass the soot and candle flame vapors through a hot (500C+?) metal tube along with more air.
Another idea i got was to slowly, with a needle valve, meter the liquid waste into the core of a torch flame, but this wouldnt be suitable for much of
my waste thats too thick or contains particles of crud.
|
|
|
karlos³
International Hazard
Posts: 1520
Registered: 10-1-2011
Location: yes!
Member Is Offline
Mood: oxazolidinic 8)
|
|
Shulgin had a walled pit in his garden, I don't think that would be legal here, or in these days.
For your quantities, well, I assume there is other stuff in there too?
Because soot is rather coming from what else was in the solvents.
Instead of burning, if you drive a diesel, you can just redistill and collect the toluene, and when clean, pour it in your cars tank.... I think
toluene has an octane number of 125 or the like! 
For comparison, nitromethane has "just" an octane number of 110!
Your car is definitely the best device to burn such solvents sootfree.
PS: syn wrote me because of our not so ideal encounter in the morning, no worries, its all fine 
verrückt und wissenschaftlich
|
|
|
Tsjerk
International Hazard
Posts: 3032
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Can't you evaporate? Quantities < 100 ml would be gone relatively quickly, and are small enough not to hurt the environment significantly. If you
have a garden or so you could place a container in a far end, maybe change it now and then when it gets very dirty.
|
|
|
BromicAcid
International Hazard
Posts: 3253
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
I used to chew up my organics with some Fenton's reagent. It will also eat aromatics converting them to benzoic acids first. On the plus side it's
affordable and the reagents are somewhat available. On the minus side it can take awhile with immiscible phases and I have had concentrated Fenton's
reagent go out of control and heat up enough to start boiling.
|
|
|
Amos
International Hazard
Posts: 1406
Registered: 25-3-2014
Location: Yes
Member Is Offline
Mood: No
|
|
Quote: Originally posted by BromicAcid  | | I used to chew up my organics with some Fenton's reagent. It will also eat aromatics converting them to benzoic acids first. On the plus side it's
affordable and the reagents are somewhat available. On the minus side it can take awhile with immiscible phases and I have had concentrated Fenton's
reagent go out of control and heat up enough to start boiling. |
Did/can you make Fenton's reagent with 3% hydrogen peroxide or will a solution that dilute not have sharp enough teeth?
[Edited on 9-4-2021 by Amos]
|
|
|
RustyShackleford
Hazard to Others
Posts: 200
Registered: 10-12-2020
Location: Northern Europe
Member Is Offline
|
|
| Quote: Originally posted by Tsjerk | | Can't you evaporate? Quantities < 100 ml would be gone relatively quickly, and are small enough not to hurt the environment significantly. If you
have a garden or so you could place a container in a far end, maybe change it now and then when it gets very dirty. |
ofc i could, but it would be more responsible to burn
i really do quite like the idea of sticking it in an engine like karlos proposed, not in car engine but ill try it with mower and trimmer. If it works
that will be a really easy solution
|
|
|
andy1988
Hazard to Others
Posts: 135
Registered: 11-2-2018
Location: NW Americus ([i]in re[/i] Amerigo Vespucci)
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by RustyShackleford |
i really do quite like the idea of sticking it in an engine like karlos proposed, not in car engine but ill try it with mower and trimmer. If it works
that will be a really easy solution |
Garden equipment might not be the best. From my understanding those inefficient 2-stroke engines may release a substantial amount of their fuel into
the air uncombusted.
EDIT: After re-reading the thread I guess that would be fine. But I do recall seeing a dissolving/fragmenting gasket on a YouTube
show, with a claim that an user-added additive with solvent action was a likely cause of the wear.
[Edited on 6-9-2021 by andy1988]
|
|
|
macckone
Dispenser of practical lab wisdom
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
A waste oil burning furnace for melting metal are in common use.
The waste oil burners may not be ideal but they will definitely burn aromatics.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
