wg48temp9
National Hazard
Posts: 786
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline
|
|
Flux for soft soldering stainless steel
From patent US3660127A a few examples of flux for soldering stainless steel, most examples use OTC materials. I have not tried any of them yet.
and just incase your google is broken the patent is at: https://patents.google.com/patent/US3660127A/en
I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
|
|
|
zed
International Hazard
Posts: 2284
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Ummm. Anodize the stainless in a copper sulfate solution, when the stainless turns black, reverse the polarity and plate out copper on the stainless
steel. Rinse, dry, flux and solder. Should be no problem.
Strength of bond? I don't know.
|
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Strength of bond is probably not going to be very strong. For structural integrity I'd guess no good, for electrical connection yeah it might hold.
just get it welded.
|
|
|
wg48temp9
National Hazard
Posts: 786
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline
|
|
Quote: Originally posted by zed  | Ummm. Anodize the stainless in a copper sulfate solution, when the stainless turns black, reverse the polarity and plate out copper on the stainless
steel. Rinse, dry, flux and solder. Should be no problem.
Strength of bond? I don't know. |
Generally in electroplating practice they go to a lot of trouble to clean the part and in particular to remove surface oxide. So anodising the SS
first seems like a terrible idea to me.
I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
|
|
|
wg48temp9
National Hazard
Posts: 786
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline
|
|
| Quote: Originally posted by draculic acid69 | | Strength of bond is probably not going to be very strong. For structural integrity I'd guess no good, for electrical connection yeah it might hold.
just get it welded. |
Yes TIG welding is the way to go if the distortion is not significant. but my TIG welding skill is terrible. But it is getting better but slowly.
After getting zinc fume fever a few times from practicing with zinc plated steel I have not had much practice. I need a fume extraction welding
table. in effect an upside down fume hood LOL
I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
|
|
|
johnsonnamedborris99
Harmless
Posts: 3
Registered: 11-12-2018
Location: over here
Member Is Offline
|
|
thats what tig welding is for
just another politically incorrect canceled culture
|
|
|
Fulmen
International Hazard
Posts: 1725
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
Nah, all you need is clean steel. Zinc will f*ck up both you and your weld.
We're not banging rocks together here. We know how to put a man back together.
|
|
|
wg48temp9
National Hazard
Posts: 786
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline
|
|
Having been, as you put it f*cked up, (flue like symptoms) by inhaling an estimated few mg of zinc oxide dust a few times, I am going to take the
advice of many including mine and take precautions to avoid inhaling any welding fumes.
Ideally I want a positive pressure welding helmet. I do have an auto darkening mask (best thing since sliced bread LOL) Since being given a battery
powered vacuum cleaner, I have considered using its blower to supply clean air to a hood I will have to attach to my mask.
I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
|
|
|
Fulmen
International Hazard
Posts: 1725
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
Honestly, it's not that hard. None of your suggestions are bad, far from it, but they aren't necessary as long as you stay away from plated metal. You
can't weld through it, and grinding the metal clean presents another source of exposure.
I've been TIG-welding a fair bit of stainless the last few months, most of the time I don't even bother turning on the extraction fan (I do for
cutting and grinding).
Now if you're also using MIG or stick some smoke control is required so why not do it right from the start. Just saying you can do TIG
without it.
We're not banging rocks together here. We know how to put a man back together.
|
|
|
markx
National Hazard
Posts: 646
Registered: 7-8-2003
Location: Northern kingdom
Member Is Offline
Mood: Very Jolly
|
|
Hydrochloric acid and zinc chloride in combination with a silver bearing solder work pretty good on soldering stainless. Surfaces must be cleaned
abrasively beforehand to remove most of the oxide coating. I have not had much of a success with phosphoric acid based concoctions.
Electrolytically etched surfaces can sometimes be notoriously difficult to solder, so I would stay away from that path.
Of course nothing beats TIG welding....it is a wonderful method for joining basically all known alloys. Nowadays machines are very compact and have a
plethora or modes to perform quite the magic on precision melting of metals.
[Edited on 29-7-2021 by markx]
Exact science is a figment of imagination.......
|
|
|
Panache
International Hazard
Posts: 1290
Registered: 18-10-2007
Member Is Offline
Mood: Instead of being my deliverance, she had a resemblance to a Kat named Frankenstein
|
|
Stick or arc welding with stainless rods is a no brainer and ensures adequate 'penno' on the weld (thats penetration for all you welding jargon
ignooramiuses!).
Problem is doing any fine work, fuck no.
|
|
|
wg48temp9
National Hazard
Posts: 786
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline
|
|
| Quote: Originally posted by Panache | Stick or arc welding with stainless rods is a no brainer and ensures adequate 'penno' on the weld (thats penetration for all you welding jargon
ignooramiuses!).
Problem is doing any fine work, fuck no. |
Unfortunately its mostly fine work joining SS vacuum flanges to SS tubes with wall thicknesses from about 0.5mm to 2mm with diameters of 25mm to
100mm. With my skill level it will not be possible with stick welding, a bit like trying to weld a car body with a stick welder. It has to be MIG or
TIG.
I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
|
|
|
Panache
International Hazard
Posts: 1290
Registered: 18-10-2007
Member Is Offline
Mood: Instead of being my deliverance, she had a resemblance to a Kat named Frankenstein
|
|
| Quote: Originally posted by wg48temp9 | | Quote: Originally posted by Panache | Stick or arc welding with stainless rods is a no brainer and ensures adequate 'penno' on the weld (thats penetration for all you welding jargon
ignooramiuses!).
Problem is doing any fine work, fuck no. |
Unfortunately its mostly fine work joining SS vacuum flanges to SS tubes with wall thicknesses from about 0.5mm to 2mm with diameters of 25mm to
100mm. With my skill level it will not be possible with stick welding, a bit like trying to weld a car body with a stick welder. It has to be MIG or
TIG. |
Oh ive got a box of new stainless vacuum flanges and other associated high vacuum miscellleana, if you want them you csnhave them, let me know and
I will post photos, theres a bunch of various parani gauges. (Sorry not gauges just the detectors) some flanged through electrical shit etc.
It was all new parts gotten from the thermo fischer waste bin...they love buying companies, closing them down and throwing all the parts!
|
|
|
Panache
International Hazard
Posts: 1290
Registered: 18-10-2007
Member Is Offline
Mood: Instead of being my deliverance, she had a resemblance to a Kat named Frankenstein
|
|
And here’s a group shot omitting the 576478548(it’s probably not that many),annealled, individually packaged, copper seal rings in the various
sizes.
I’m in Melbourne Australia though....there’s also all those piraña ( detectors if you want some ...the thread is in the materials section, it
bugged out initially so the photo isn’t till the end of the thread.
|
|
|
stamasd
Hazard to Others
Posts: 137
Registered: 24-5-2018
Location: in the crosshairs
Member Is Offline
Mood: moody
|
|
Soldering stainless steel is going to be a futile endeavor. And if TIG welding is not an option, I suggest a 3rd option: brazing. One uses silver
solder and specific fluxes for that. It can be done with a propane torch, and requires less skill than TIG. It should be good enough for low vacuum -
wouldn't guarantee for high vacuum though.
(edit) there are instructional videos for brazing stainless steel all over youtube.
[Edited on 22-9-2021 by stamasd]
All your acids are belong to us.
|
|
|
markx
National Hazard
Posts: 646
Registered: 7-8-2003
Location: Northern kingdom
Member Is Offline
Mood: Very Jolly
|
|
| Quote: Originally posted by stamasd | Soldering stainless steel is going to be a futile endeavor. And if TIG welding is not an option, I suggest a 3rd option: brazing. One uses silver
solder and specific fluxes for that. It can be done with a propane torch, and requires less skill than TIG. It should be good enough for low vacuum -
wouldn't guarantee for high vacuum though.
(edit) there are instructional videos for brazing stainless steel all over youtube.
[Edited on 22-9-2021 by stamasd] |
I would not say that soldering stainless steel is a futile attempt. I've been successful on many attempts with silver bearing solder and hydrochloric
acid based flux. Soldering thermometer ports into reflux column e.g. Soldering copper pipes to thin stainless mounting plate in a heat exchanger. So
it can be done and has a purpose in lack of other options. The joints lack the strength of a weld or braze, but for small parts that do not have to
endure a lot of stress it makes sense. Soldering is also desirable if distortion of the parts is to be avoided. Brazing and especially welding of
stainless shall induce a lot of stress distortion even when done skillfully and with undue involvement of extra heat. I guess it all depends what
kind of conditions the joint has to survive....if they are decently mild, then a soldered connection may do quite ok as far as practical purposes are
considered.
Exact science is a figment of imagination.......
|
|
|
wg48temp9
National Hazard
Posts: 786
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline
|
|
| Quote: Originally posted by stamasd | Soldering stainless steel is going to be a futile endeavor. And if TIG welding is not an option, I suggest a 3rd option: brazing. One uses silver
solder and specific fluxes for that. It can be done with a propane torch, and requires less skill than TIG. It should be good enough for low vacuum -
wouldn't guarantee for high vacuum though.
(edit) there are instructional videos for brazing stainless steel all over youtube.
[Edited on 22-9-2021 by stamasd] |
Thanks for the suggestion. I did consider that but I thought the distortion and oxidation would damage the vacuum flanges.
I checked out the video (the link below) of a guy silver soldering a SS coupling to a SS pot using a small propane torch. It did easily melt the
silver solder though I don't know what type of silver solder it was. The oxidation did not look significant so I will try it after I order the lowest
melting temperature silver solder I can buy.
https://www.youtube.com/watch?v=OpMFQFi6Hh4
I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
|
|
|
wg48temp9
National Hazard
Posts: 786
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline
|
|
| Quote: Originally posted by Panache | And here’s a group shot omitting the 576478548(it’s probably not that many),annealled, individually packaged, copper seal rings in the various
sizes.
I’m in Melbourne Australia though....there’s also all those piraña ( detectors if you want some ...the thread is in the materials section, it
bugged out initially so the photo isn’t till the end of the thread.
|
Thanks for the offer. I guess the cost of posting almost anything bigger than a letter from Australia to the UK will be expensive. Sorry for the delay
in replying to you.
I have some noisey vacuum gauges and I eventually splashed out (~£40) on a used full range gauge believed to be good. I tested it on one of my well
used and noisy vacuum pumps filled with filtered oil. It went down to about 30 microns but the reading was fluctuating +/-30 microns. Possibly caused
by the pulsing from the pump. When I turned off the pump the oil was sucked up in to the gauge is less than minute while the oil level in the sight
glass dropped about about 15mm. Ouch! I guess the gauge is out of calibration now.
[Edited on 9/23/2021 by wg48temp9]
I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
|
|
|
stamasd
Hazard to Others
Posts: 137
Registered: 24-5-2018
Location: in the crosshairs
Member Is Offline
Mood: moody
|
|
| Quote: Originally posted by wg48temp9 |
Thanks for the suggestion. I did consider that but I thought the distortion and oxidation would damage the vacuum flanges.
I checked out the video (the link below) of a guy silver soldering a SS coupling to a SS pot using a small propane torch. It did easily melt the
silver solder though I don't know what type of silver solder it was. The oxidation did not look significant so I will try it after I order the lowest
melting temperature silver solder I can buy.
https://www.youtube.com/watch?v=OpMFQFi6Hh4 |
For stainless steel to be used for vacuum, I recommend using a "hard" silver solder, i.e. a solder with a high % of silver. That does not mean that it
will have a higher melting point though: compare the 35% silver and the 56% silver solders below
https://www.harrisproductsgroup.com/en/Products/Alloys/Brazi...
https://www.harrisproductsgroup.com/en/Products/Alloys/Brazi...
the 56% silver solder actually melts at a lower temperature than the 35% one. It's still above 600C though. I'd recommend the 56% one.
(edit) and even though the filler material is called "solder", the procedure is still brazing not soldering.
(edit2) and if you're looking for the best way to make non-permanent unions of vacuum parts, i.e. gaskets, the best material for vacuum gaskets in my
experience is pure indium. It's very soft, does not leak, and it's completely recyclable. You can reuse it indefinitely to make custom gaskets as it
melts at low temperature. I use custom molds made from silicone rubber for that. The major downside of indium is the cost. It's expensive. But a
little goes a long way. For instance, you need less than 3g to make a gasket for a KF50 joint.
[Edited on 23-9-2021 by stamasd]
All your acids are belong to us.
|
|
|
wg48temp9
National Hazard
Posts: 786
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline
|
|
Apparently most silver solders contain zinc in addition to silver and copper. Zinc is not recommended for high vacuum use because of its high vapor
pressure.
So I thought I should check what its vapour pressure is near room temperature. It appears to be less than 10^-10 bar at 400K so it is probably not
significant for anything I want to do.
I found the following graphs plotting the vapour pressure vs temperature. of the common elements. They may be useful to others.
Sorry I directly loaded the second graph from the original paper (https://www.powerstream.com/vapor-pressure.htm. ) its full size so its huge.
[Edited on 9/29/2021 by wg48temp9]
I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
