Newton2.0
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 63
Registered: 12-8-2019
Member Is Offline
|
|
Various chlorotoluenes produced during Toluene+TCCA+uv synthesis
I have variety of fractions obtained from the chlorination of toluene using TCCA and I'm trying to figure out how to classify them.
My pitiful brute force search comparisons of chlorinated toluenes against their boiling points between 150-205C have only yielded:
ortho/meta/para-chlorotoluenes 159-162C
benzyl chloride 179C
benzal chloride 205C
Di-/tri-substituted chlorides are too-high boiling to fall in this range. And I'm not really interested in polymerized chlorotoluenes or the
miscellaneous organic nonsense that's going to be present. Chemistry is messy.
Shall I assume the these values are, in practice, "blurred" due to my use of only a 300mm vigreaux column and imprecise temp monitoring. As in, the bp
of a relatively pure fraction of benzyl chloride might really end up falling in a range from 177C-182C?
Let me know what your thoughts are, please!
|
|
RustyShackleford
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 198
Registered: 10-12-2020
Location: Northern Europe
Member Is Offline
|
|
My experience w that reaction was that it almost only formed benzyl chloride, did you add something like FeCl3 to form the ring substituted toluenes?
|
|
Metacelsus
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2537
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
Reaction with Cl2 will mostly form benzyl chloride, by radical halogenation. I'm not sure about TCCA though, since it probably doesn't form radicals
as easily as Cl2 does.
Can you provide more info about your reaction conditions?
|
|
Newton2.0
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 63
Registered: 12-8-2019
Member Is Offline
|
|
200g TCCA is added over a period of three days to a 3-neck 1L RBF containing 425mL toluene. Then a UV-C light intended for hand sanitization is
applied to the side of the RBF and a halogen lamp (no specs) is used on the opposite side.
At some point there was a runaway thermal issue which caused a portion of the solid to polymerize and tar. The reaction was left to run for a total of
six days and filtered on a Büchner funnel.
Then I set up for fractional distillation with a 300mm vigreaux column. I obtained a huge amount of liquid between 150 and 200C which leads me to
wonder if I made additional products. Radical mechanisms might have created something different.
However, if I made almost exclusively BzCl, that would be fantastic!
|
|
Newton2.0
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 63
Registered: 12-8-2019
Member Is Offline
|
|
I recognize now that the way I would get ring-substituted chlorine is with the addition of FeCl3 and then separating later. Thanks!
What I have is most likely BzCl and toluene and miscellaneous junk from the TCCA breakdown products. I kept everything that came over between 175-185C
and redistilled to about approximately 62mL of relatively clean BzCl. It has been stored in amber bottles, however, I expect the shelf life is
terrible.
|
|
egret
Harmless
Posts: 20
Registered: 22-2-2018
Member Is Offline
Mood: No Mood
|
|
Benzyl chloride can be stabilised by aqueous sodium carbonate. I tried it and it works. The benzylchloride is siting on the shelve 9 months without
visible degradation. I thing it was discussed here in the forum but I can´t find it.
Google patent
https://patents.google.com/patent/US2542216A/en
"Benzyl chloride is presently stabilized with a 10% aqueous sodium carbonate solution. Benzyl chloride thus stabilized may be safely shipped in black
iron drums without danger of decomposition in the event of accidental contamination with iron, rust or iron salts. For example, 450 pounds of benzyl
chloride mixed with 23 pounds of a 10% aqueous sodium carbonate solution may be safely shipped in a gallon black iron drum. This wet stabilized
material is a milky-white emulsion, from which a water layer may separate upon standing. However, before use, the benzyl chloride must be recovered
from the stabilized solution, as anhydrous liquid benzyl chloride is preferred and necessary for most operations."
|
|
Newton2.0
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 63
Registered: 12-8-2019
Member Is Offline
|
|
Excellent! This is a great find! I appreciate this very much. I will make sure to add the appropriate amount to stabilize and then reclaim the BzCl
when it's needed.
|
|
zed
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2281
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Might be easier to make it from Benzyl Alcohol.
Of note, the reaction produces several products. Benzyl Chloride, Benzyl Dichloride, Benzyl Trichloride.
On hydrolysis those products produce respectively: Benzyl Alcohol, Benzaldehyde, and Benzoic Acid.
Nasty stuff, Benzyl Chloride. Serious Lacrimator.
I can buy Benzyl Alcohol by the gallon, cheap. Same goes for Benzoic Acid. Benzaldehyde, not so much. Hard to acquire, in a lot of jurisdictions.
If you have a hankering for Acid Chlorides, like Acetyl Chloride Etc... Benzaldehyde can take you there. It can react with Cl2 to form Benzoyl
Chloride, by which other Acid Chlorides may be synthesized.
[Edited on 16-4-2021 by zed]
[Edited on 16-4-2021 by zed]
[Edited on 16-4-2021 by zed]
|
|
Newton2.0
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 63
Registered: 12-8-2019
Member Is Offline
|
|
As a matter of fact, I do have my eyes set on a few acid chlorides, namely propionyl chloride and butyryl chloride. I was just going to go the PCl5
route. But benzyl alcohol is way cheaper.
|
|