Cou
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 958
Registered: 16-5-2013
Member Is Offline
Mood: Mad Scientist
|
|
Question about storage of recycled solvents
when you recycle solvents by simple distillation, do you pour the recycled solvent back into the original container with unused solvent, or do you set
aside a 2nd storage bottle for the recycled solvent until you use up the entire original bottle?
it's less convenient to have 2 sets of storage for every solvent. one bottle from the manufacturer and a 2nd bottle for recycled solvent.
[Edited on 4-12-2021 by Cou]
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2690
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
I often reuse colvent from simple things, sometimes I reuse the original container, but always mark it as "recovered" over the original label, this is
most common with 4L bottles. For most solvents, I will store them in a glass 1L bottle and label it as recylced or recovered or for acetone, often
"rinse" or :bath" acetone. 95-99% pure acetone is good enough to prerinse glassware, make dry ice bathes or soak small items in. Hexane and ethyl
acetate can often be recovered from columns, and DCM and ether can easily be recycled by rotovaping the solvent under very gentle vacuum and low temp,
which will mostly pull them away from other solvents.
|
|
Cou
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 958
Registered: 16-5-2013
Member Is Offline
Mood: Mad Scientist
|
|
at home I recycle ether by simple distillation with a graham condenser with ice cold water and receiving flask in ice cold water.
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
I dump them back in the original containers.
If I need extra high purity, I will get a new bottle or fractionally distill and perform extra steps for it. For general use, refining stuff takes way
too much time.
|
|
FrenchChemist
Harmless
Posts: 43
Registered: 25-1-2021
Member Is Offline
|
|
I do exactly the same as others, simple distillation is not a problem and allows you to get very good purity.
If I need a dry one, I add 3A molecular sieves or silica gel depending on the substance, of course.
In the case of solvents such as DCM, chloroform ether, dichloroethane, for obvious reasons, only glass bottles.
|
|
njl
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 609
Registered: 26-11-2019
Location: under the sycamore tree
Member Is Offline
Mood: ambivalent
|
|
I have a big jug of solvent and a smaller 1 liter bottle which is empty, I fill the 1 liter bottle for use and redistilled solvents go back into that.
So I have a clean enough liter on hand for use and more pure solvent left in the jug.
Reflux condenser?? I barely know her!
|
|