OctanitroC
Harmless
Posts: 21
Registered: 20-4-2012
Location: Near the nadir of a triangular state
Member Is Offline
Mood: Reduced
|
|
Properties of diphenhydramine base?
Hello everybody, I was wondering if you could help me out with something. I'm performing an extraction of diphenhydramine from generic allergy pills;
I crushed 76 pills, containing 1.9 g diphenhydramine HCl, and mixed the resulting powder with 200 mL of water to dissolve the hydrochloride. I then
filtered off the supernatant to obtain 200 mL of a very faintly pink (from the pill coating), clear solution. I mixed this solution with an excess of
NaOH solution, which caused the solution to immediately become cloudy. After this, I let the solution stand, but no separation occurred, so I added 20
g of NaCl to try to salt out the diphenhydramine base. This cleared the solution significantly and caused an oily liquid to come out of suspension and
float on top of the solution. I'm not sure what this would be other than product, but I'm confused as to it being an oil. The (admittedly spotty)
references I found all seemed to point to both the base and hydrochloride of diphenhydramine being solid at room temperature. Does anybody have a
reference for the melting point of diphenhydramine in the base form, rather than the hydrochloride? I'd appreciate any help. Thanks!
And then I discovered this charming young man had stolen my kidney!
|
|
|
Burner
Hazard to Others
Posts: 100
Registered: 28-3-2014
Member Is Offline
Mood: No Mood
|
|
The melting point of the base (CAS# 58-73-1) is reported as 167C-172C (http://www.chemnet.com/cas/en/58-73-1/diphenhydramine.html).
[Edited on 9-7-2014 by Burner]
“There is a cult of ignorance in the United States, and there has always been. The strain of anti-intellectualism has been a constant thread winding
its way through our political and cultural life, nurtured by the false notion that democracy means that 'my ignorance is just as good as your
knowledge.”
- Isaac Asimov
|
|
|
AvBaeyer
National Hazard
Posts: 651
Registered: 25-2-2014
Location: CA
Member Is Offline
Mood: No Mood
|
|
Diphenylhydramine (CAS 58-73-1) is a liquid (bp 150-165 @ 2mm): See Merck Index 14th edition, 3309. Diphenylhydramine hydrochloride (CAS 147-24-0) has
mp 166-170. So the oil you have is in all likelihood the desired freebase which you will need to isolate by extraction with a suitable solvent
followed by an appropriate workup.
AvB
|
|
|
Nicodem
|
Thread Moved
9-7-2014 at 08:33 |
OctanitroC
Harmless
Posts: 21
Registered: 20-4-2012
Location: Near the nadir of a triangular state
Member Is Offline
Mood: Reduced
|
|
Alright, thanks! I lost quite a bit of the oil trying to pipette it out, so I'm re-running the extraction with 2.5 g of the hydrochloride. Will add
the crude wet product to toluene and dry the toluene solution over anhydrous MgSO4, decant, then let the toluene evaporate off; that should eliminate
water and water-soluble salts, etc. from the product.
And then I discovered this charming young man had stolen my kidney!
|
|
|
AvBaeyer
National Hazard
Posts: 651
Registered: 25-2-2014
Location: CA
Member Is Offline
Mood: No Mood
|
|
You need to be careful about evaporating your solvent in air as diphenylhydramine, being an amine, will absorb CO2 giving you a relatively useless
solid. Do you have the means to gently distill off the toluene? Magnesium sulfate will not remove all the water whereas gentle distillation will via
the azeotrope. A better drying agent would be solid sodium hydroxide followed by gentle distillation. A mild vacuum would be very useful for this. Do
you have a more volatile solvent like methylene chloride rather than toluene?
AvB
|
|
|
Nicodem
Super Moderator
Posts: 4230
Registered: 28-12-2004
Member Is Offline
Mood: No Mood
|
|
Toluene is not a good choice for the final extractions as it is terribly difficult to remove. I suggest you to rather form a stable salt
(hydrochloride, oxalate, etc.). If you insist on isolating the free base, then first rotavap off the toluene (or whatever device you have to remove
solvents), then add a more volatile solvent (methanol, MTBE, etc.) and evaporate under reduced pressure again, repeat one or two more times (this
usually efficiently removes the toluene even from liquid products or amorphous solids).
The general indications for choosing an appropriate extraction solvent based on the properties of the compound can be found in this thread.
Quote: Originally posted by AvBaeyer  | | You need to be careful about evaporating your solvent in air as diphenylhydramine, being an amine, will absorb CO2 giving you a relatively useless
solid. |
As far as I know, that does not occur with tertiary amines, since they cannot form the corresponding ammonium carbamates like the primary and
secondary amines do.
…there is a human touch of the cultist “believer” in every theorist that he must struggle against as being
unworthy of the scientist. Some of the greatest men of science have publicly repudiated a theory which earlier they hotly defended. In this lies their
scientific temper, not in the scientific defense of the theory. - Weston La Barre (Ghost Dance, 1972)
Read the The ScienceMadness Guidelines!
|
|
|
Rich_Insane
Hazard to Others
Posts: 371
Registered: 24-4-2009
Location: Portland, Oregon
Member Is Offline
Mood: alive
|
|
Use DCM to isolate the base and then wash the organic layer with water. Remove the DCM under reduced pressure or try to evaporate/boil it away. That
would be the best course of action. Salts are a lot easier to work with than freebase amines.
|
|
|
SuperOxide
Hazard to Others
Posts: 487
Registered: 24-7-2019
Location: Devils Anus
Member Is Offline
|
|
@OctanitroC - Did this ever work out? Curious what your results were, or if you chose a different procedure. You're right about the
details on the properties of diphenhydramine being a little spotty on the internet. The sources I was able to find didn't have too much on
its chemical properties or solubility in different solvents (other than water), and they seemed to be contradicting other sources.
P.S. - I apologize for reviving an old thread. I was just looking into some diphenhydramine extraction as well and found this thread. Thought it was
better to revive an old relevant thread than to post a duplicate.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
