insutama
Harmless
Posts: 33
Registered: 31-3-2015
Member Is Offline
Mood: No Mood
|
|
ETN first attempt
I am about to attempt my first ETN synth I was just wondering if i could use the same mix of acids i used when i made PETN
34 ml of 67% HNO3
24.8 ml of 98% H2SO4
and i was gonna use 10 grans Erythritol
any suggestions ?
|
|
XeonTheMGPony
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
Search the forum, do the math?
|
|
insutama
Harmless
Posts: 33
Registered: 31-3-2015
Member Is Offline
Mood: No Mood
|
|
Okay I did some calculations and what I have come up with is
24mg HNO3 67%
36mg H2SO4 98%
6 grams Erythritol
I put this here incase anyone else was looking for this info Ill let you know how it turns out
|
|
Laboratory of Liptakov
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-9-2014
Location: Technion Haifa
Member Is Offline
Mood: old jew
|
|
You mean sure mililiters not miligrams I estimate. You need 24 ml x 1.4 = 33,6 g HNO3 + 36 x 1,85 = 66,6g H2SO4.
+ 6g Erythritol........
Development of primarily - secondary substances CHP (2015) Lithex (2022) Brightelite (2023) Nitrocelite and KC primer (2024)
|
|
insutama
Harmless
Posts: 33
Registered: 31-3-2015
Member Is Offline
Mood: No Mood
|
|
lol ya i meant ml my bad i just made it and everything went smooth its drying now ill have to test it tomorrow
|
|
XeonTheMGPony
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
Hope fully you read all the big threads to save time and help ensure a good clean pure product!
|
|
insutama
Harmless
Posts: 33
Registered: 31-3-2015
Member Is Offline
Mood: No Mood
|
|
Seemed to work out good i did a half batch to test it so only used 3 grams of erythritol its still drying ill post the weight when its fully dried
came out a nice white powder no discoloration ill do a acetone recrystallization once its dried
|
|
Jebby
Harmless
Posts: 15
Registered: 25-7-2019
Member Is Offline
|
|
I used Roto Professional liquid drain cleaner and spectracide stump remover In a failed attempt to synthesize ETN and when I mixed the 100g of drain
cleaner and 40g of stump remover it turned from a slight yellow color to a almost red color the consistency was that of pudding and apple sauce
(viscous and very slightly gritty or chunky). I was wondering if anyone knows what caused this and how I can prevent it.
|
|
B(a)P
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1139
Registered: 29-9-2019
Member Is Offline
Mood: Festive
|
|
The solid was likely potassium sulphate. Was the mixture letting off a gas? The red colour may have been dissolved NO2.
Did you cool the acid before adding the KNO3. The reaction is very exothermic and additions need to be done in portions with cooling.
|
|
Jebby
Harmless
Posts: 15
Registered: 25-7-2019
Member Is Offline
|
|
The acid was cooled to around 0°C. It was letting of a white vapor. Do you think that the potassium sulphate would hinder the nitration of the
Erythritol?
|
|
B(a)P
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1139
Registered: 29-9-2019
Member Is Offline
Mood: Festive
|
|
Quote: Originally posted by Jebby ![](images/xpblue/lastpost.gif) | The acid was cooled to around 0°C. It was letting of a white vapor. Do you think that the potassium sulphate would hinder the nitration of the
Erythritol? |
Potassium sulfate will not hinder the nitration of erythritol. There are many threads on this forum discussing the nitration of erythritol, have you
tried working your way through those? If so can you give a bit more detail on what you did following the the addition of KNO3 to
H2SO4.If you are nitrating erythritol with H2SO4 and a nitrate salt you will always end up with a
nitration mixture of the consistency you described.
|
|
Jebby
Harmless
Posts: 15
Registered: 25-7-2019
Member Is Offline
|
|
I have tried to work through a synthesis that I found on bitchute the only real big problem was the solubility, I have been told to add more SA to
dissolve it completely. I will have to try the synthesis again today.
|
|
B(a)P
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1139
Registered: 29-9-2019
Member Is Offline
Mood: Festive
|
|
Quote: Originally posted by Jebby ![](images/xpblue/lastpost.gif) | I have tried to work through a synthesis that I found on bitchute the only real big problem was the solubility, I have been told to add more SA to
dissolve it completely. I will have to try the synthesis again today. |
The trouble with copying what you see on a video is that you will often miss important details that the producer glosses over or omits all together.
This is particularly true when you are using technical grade reagents. Did the producer of the video also use technical grade reagents, were they the
same concentration or brand as you are using, are you sure any additives in your reagents won't hinder the reaction? If you work your way through
other peoples mistakes you are much more likely to succeed. Also it is a good idea to find credible published procedures to have as a reference. When
you are working with toxic or energetic reactants or products it is advisable to be very certain of the required reaction conditions be aware what
could go wrong and have measures in place to mitigate against a worst case scenario. Know that although ETN is classified as a secondary explosive it
is, compared to many other secondaries, very sensitive to thermal shock and in its liquid state it behaves more or less as a primary.
It is important to write out the reaction formula and work your way through the stoichometry to make sure you are convinced that you are using the
correct mass of reactants. This will allow you to modify your approach if you are using reagents of a different concentration to the video you are
basing your synthesis on. It will also allow you to test your yield to see how successful the synthesis was and help make improvements in the future.
Out of curiosity what video are you following? What made you think the consistency of your mixed acids caused your reaction to fail?
|
|
DBX Labs
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 57
Registered: 24-12-2020
Member Is Offline
|
|
Quote: Originally posted by B(a)P ![](images/xpblue/lastpost.gif) | Quote: Originally posted by Jebby ![](images/xpblue/lastpost.gif) | I have tried to work through a synthesis that I found on bitchute the only real big problem was the solubility, I have been told to add more SA to
dissolve it completely. I will have to try the synthesis again today. |
The trouble with copying what you see on a video is that you will often miss important details that the producer glosses over or omits all together.
This is particularly true when you are using technical grade reagents. Did the producer of the video also use technical grade reagents, were they the
same concentration or brand as you are using, are you sure any additives in your reagents won't hinder the reaction? If you work your way through
other peoples mistakes you are much more likely to succeed. Also it is a good idea to find credible published procedures to have as a reference. When
you are working with toxic or energetic reactants or products it is advisable to be very certain of the required reaction conditions be aware what
could go wrong and have measures in place to mitigate against a worst case scenario. Know that although ETN is classified as a secondary explosive it
is, compared to many other secondaries, very sensitive to thermal shock and in its liquid state it behaves more or less as a primary.
It is important to write out the reaction formula and work your way through the stoichometry to make sure you are convinced that you are using the
correct mass of reactants. This will allow you to modify your approach if you are using reagents of a different concentration to the video you are
basing your synthesis on. It will also allow you to test your yield to see how successful the synthesis was and help make improvements in the future.
Out of curiosity what video are you following? What made you think the consistency of your mixed acids caused your reaction to fail?
|
I believe that Jebby is referring to this video.
https://www.bitchute.com/video/XrjpCnYs7fVL/
From my recollection, the solution of 40 grams AN in only 100 grams SA is quite difficult to produce with impure AN. As mentioned in the video,
recrystallization is necessary.
I just realized that KNO3 was mentioned as the source of nitrate. If that's still the case, this video is not relevant.
[Edited on 23-2-2021 by DBX Labs]
|
|
Pyro_cat
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 243
Registered: 30-4-2018
Member Is Offline
Mood: No Mood
|
|
I got it to work first try with the three off the shelf reagents.
You need a thick sloppy mix of KNO3, Sulfuric and add in one quarter the amount of E you have to KNO3 stir temps time
Thick sloppy mix means your ratio is right.
My first nitration experiments were with cotton and I learned from that mixing up that goop.
[Edited on 24-2-2021 by Pyro_cat]
|
|
Jebby
Harmless
Posts: 15
Registered: 25-7-2019
Member Is Offline
|
|
The link that DBX posted was the video I was talking about. The reason I thought the consistency of the mixed acids caused a failure is because I
didn’t think that the nitration would occur because of how hard it would be to mix. B(a)P I’d like to thank you for the help as I am relatively
new to all this, and your advice is very helpful.
|
|
DBX Labs
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 57
Registered: 24-12-2020
Member Is Offline
|
|
Yeah, AN/SA nitrating mixtures are thin and clear when pure even down to 0C. On the other hand, KNO3/SA mixtures are rarely anything but thick and
gooey. That’s why I prefer AN over KNO3 for most all nitrations, nitrocellulose included.
|
|
B(a)P
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1139
Registered: 29-9-2019
Member Is Offline
Mood: Festive
|
|
I have tried with technical grade (from the hardware store) KNO3 and H2SO4 and never achieved better than 60% yield.
With this reaction it is a thick paste and it needs continual stirring with a glass rod. The erythritol needs to be added in small portions with lots
of stirring in between to mitigate localised hotspots due to the consistency of the reaction mixture.
With laboratory reagent grade azeotropic mixed acids I have achieved 95% yield.
If you are new to this and you are basing your reaction on that video only you are missing an important step, you need to do more research.
Read through the following threads.
https://www.sciencemadness.org/whisper/viewthread.php?tid=24875#pid290333
https://www.sciencemadness.org/whisper/viewthread.php?tid=7209#pid82290
I have added some additional resources that may be helpful.
Keep your quantities small at first to conserve reagents while you are working out your procedure, but most of all for safety. Best of luck.
Attachment: Erythritol Tetranitrate as a Sensitizer in Ammonium Nitrate Based Explosives.pdf (213kB) This file has been downloaded 373 times
Attachment: Characterization and Analysis of Tetranitrate Esters.pdf (806kB) This file has been downloaded 341 times
|
|
Jebby
Harmless
Posts: 15
Registered: 25-7-2019
Member Is Offline
|
|
I can’t thank you enough B(a)P. Your help has been much appreciated.
|
|
Industrial Adhesive
Harmless
Posts: 15
Registered: 30-11-2018
Location: to be honest, I lost track
Member Is Offline
|
|
Quote: Originally posted by Jebby ![](images/xpblue/lastpost.gif) | I used Roto Professional liquid drain cleaner and spectracide stump remover In a failed attempt to synthesize ETN and when I mixed the 100g of drain
cleaner and 40g of stump remover it turned from a slight yellow color to a almost red color the consistency was that of pudding and apple sauce
(viscous and very slightly gritty or chunky). I was wondering if anyone knows what caused this and how I can prevent it. | its from potassium sulfate.
|
|
Industrial Adhesive
Harmless
Posts: 15
Registered: 30-11-2018
Location: to be honest, I lost track
Member Is Offline
|
|
Quote: Originally posted by Jebby ![](images/xpblue/lastpost.gif) | I used Roto Professional liquid drain cleaner and spectracide stump remover In a failed attempt to synthesize ETN and when I mixed the 100g of drain
cleaner and 40g of stump remover it turned from a slight yellow color to a almost red color the consistency was that of pudding and apple sauce
(viscous and very slightly gritty or chunky). I was wondering if anyone knows what caused this and how I can prevent it. | its from potassium sulfate.
|
|