Fulmen
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1702
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
Identification of ac motor
![_20201225_185425.JPG - 1.3MB](https://www.sciencemadness.org/whisper/files.php?pid=651992&aid=85583)
Can anybody help me with wiring this motor? It came out of an old IKA hotplate/stirrer.
It has 3 wires with very different readings:
AC inductance (120hz) and DC resistance:
1/2: 4.1H / 1.5k
2/3: 1.5H / 0.4k
3/1: 5.5H / 1.9k
[Edited on 25-12-20 by Fulmen]
We're not banging rocks together here. We know how to put a man back together.
|
|
itsallgoodjames
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 276
Registered: 31-8-2020
Location: America Lite
Member Is Offline
|
|
The motor in the picture is an induction motor, obviously intended to be used with single phase AC. As you can see, it's rated for two hundred and
twenty volts at fifty hertz. The 1 microfarad capacitor listed is the value for the capacitor in the provided diagram. In the diagram, a is wire 2,
b is either 1 or 3, and c is the opposite of b. if you wire it up according to the diagram with the appropriate capacitor, it should be fairly easy
to drive.
Nuclear physics is neat. It's a shame it's so regulated...
Now that I think about it, that's probably a good thing. Still annoying though.
|
|
Fulmen
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1702
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
Ok, so I'm making some headway. Stay with me here...
First I looked up the serial (ebm m4e060-ca01-08) which gave me a dead match from www.ebay-kleinanzeigen.de. Luckily the preview listed the following excerpt:
"Ich biete hier 4x 220V Außenläufermotoren an. Typ: ebm m4e060-ca01-08 Die dazu gehörigen". Now that has to be the same motor, right? What are the
odds?
So I look up "außenläufermotor", which gives me the translation "Permanent magnet Synchronous motor (PMSM)". Now we're getting somewhere, eh?
We're not banging rocks together here. We know how to put a man back together.
|
|
Fulmen
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1702
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
Thanks, itsallgoodjames. I forgot to mention that it's an "outrunner", don't know if that matters.
But I guess it's just a plain synchronous motor, first time I've had to deal with them so take it slow. I'm more of a mechanics guy. The plan is to
rewire the hotplate using an arduino controller. Shouldn't be harder than an optoisolator and a suitable triac for the AC. Temp sensor will be a
ready-made k-element shield, the motor has a slotted ring yjat can be read with an optical reader.
We're not banging rocks together here. We know how to put a man back together.
|
|
Fulmen
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1702
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
All good. The motor runs fine with a 0.9uF cap, guess I have to shop some components to finish the job. Thanks for the help, james.
We're not banging rocks together here. We know how to put a man back together.
|
|
Fulmen
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1702
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
This is the power board, housing the 5V PSU for the arduino and the triacs. The arduino and K-element shields will go on a separate board.
![Power1.png - 12kB](https://www.sciencemadness.org/whisper/files.php?pid=652071&aid=85625)
And yes, I see the mistakes :-)
[Edited on 27-12-20 by Fulmen]
We're not banging rocks together here. We know how to put a man back together.
|
|