Pages:
1
2 |
FranzAnton
Harmless
Posts: 45
Registered: 31-3-2020
Location: Austria
Member Is Offline
|
|
Sorry my stupid question, but if you only want to do the preparation of that ester (for historical interest) you can use H2SO4 in excess so you will
get it anyway in smaller amounts but it's possible. So if the glycerol is at leat 80% you will make it without pump and equipment.
|
|
TLutman
Harmless
Posts: 26
Registered: 13-10-2019
Member Is Offline
|
|
As a beginner into organic chemistry, I'm just trying to weigh the pro's/cons of different methods. My first few things to synthesize were things
experienced chemists would just go buy, and I might get there one day myself.
I decided to make some HNO3, which is what sparked my curiosity to begin with (thanks Nurdrage), but wanted to avoid any NO gas. I just used a $16
12V vac pump from Adafruit (electronics site), which pulled almost 30inHg IIRC. Yep, the BP was lowered. Nope, no NO. But also I could drop the vapor
column back into the boiling flask and immediately stop the boiling by breaking the vacuum at the vac adapter.
I figure the cheap pump would last a little while, and is cheap enough to just replace when it goes belly up. I might get a pump down the road that
isn't so annoying, but for now, it will do.
|
|
FranzAnton
Harmless
Posts: 45
Registered: 31-3-2020
Location: Austria
Member Is Offline
|
|
If you want to concentrate the HNO3 only by destillation (vacuum or not) you will not get much higher than approx. 68-70% because the aceotropic
concentration do not differ significantly with pressure.
So you need somethin in addition to remove water. Mg(NO3)2 or H2SO4 can help. A destillation under reduced pressure helps only to recuce decomposing
during destillation. (Intense Light speeds up the decomposing)
The higher the concentration of HNO3 the faster it will decompose. So for long therm storage a 68% solution is much more stable under the same storage
conditions that a 98%.
By the way in this forum library there is a book which will help you to get a detailed view of nitric acid (Mellor_ACTITC_v08_1931) It's old, but
really packed of information.
[Edited on 15-5-2020 by FranzAnton]
|
|
Mateo_swe
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 526
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
Thanks for that Nitric acid reading tip, i will read it.
Im just a beginner when it comes to chemistry but i will eventually try make some nitric acid and try to get as good % i can get.
I thought aspirators was the only way to do a vacuum destillation of nitric acid as it ruins any diafragm pump very quickly.
Thats what i have read at least.
Im not even considering cold trap pumps due to cost.
I have looked into making some nitric using NaHSO4 + KNO3.
What will the strength of the nitric be using this method?
I know the temps are little to high using this procedure resulting in some nasty fumes that requires it to be done outside.
I do have a DIY fumehood but this one i will be doing outside anyway.
Can aspirator vacuum be applied in this procedure to try lower the temps and reduce the decomposition of the nitric acid?
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
My pump is getting alarmingly low on oil. I looked for vacuum pump oil everywhere but can't find other but one supplier that sells €50 per liter +
20€ shipping. I tried to look for alternatives and the composition of vacuum pump oil is a close resemblance of liquid paraffin oil, which is
essentially a mineral oil. It has similar density, vapor pressure and cst value and both share the fact that they lack any additives.
To be real, what would happen if I were to just load the pump with liquid paraffin oil? I happen to have a bottle on my hand. The pump wasn't very
expensive and worst that could happen is maybe an oil mist, so would I be stupid to try it out?
I'm speaking of the european type paraffin oil that is viscous as normal lubricating oil and is used for all kinds of things, from treating woods to
skin, never as a fuel.
[Edited on 26-7-2020 by Fyndium]
|
|
monolithic
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Fyndium ![](images/xpblue/lastpost.gif) | My pump is getting alarmingly low on oil. I looked for vacuum pump oil everywhere but can't find other but one supplier that sells €50 per liter +
20€ shipping. I tried to look for alternatives and the composition of vacuum pump oil is a close resemblance of liquid paraffin oil, which is
essentially a mineral oil. It has similar density, vapor pressure and cst value and both share the fact that they lack any additives.
To be real, what would happen if I were to just load the pump with liquid paraffin oil? I happen to have a bottle on my hand. The pump wasn't very
expensive and worst that could happen is maybe an oil mist, so would I be stupid to try it out?
I'm speaking of the european type paraffin oil that is viscous as normal lubricating oil and is used for all kinds of things, from treating woods to
skin, never as a fuel.
[Edited on 26-7-2020 by Fyndium] |
I think it would work just fine. Most "purpose made" vacuum pump oils are just mineral oils which are fractionated and maybe mixed with a rust
inhibitor. This webpage explains it in a little detail: http://www.hyvac.com/Products/Oil/vac_oils.htm (They're a good source for materials on vacuum pump maintenance, too.)
Try it, I don't think it poses any risk to your pump.
[Edited on 7-26-2020 by monolithic]
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
For the record, I successfully used paraffin oil. I've also used it as joint grease.
How to cool vacuum pump?
Mine gets very hot, above 90C when running for a longer period and too hot to touch. It would be trivial to cool down with water, but that'd be more
difficult to carry out. One crazy idea that came in mind is to put the pump in a thick plastic bag and immerse it in water bath so the pump exhaust
and other necessary accessories are not blocked.
|
|
wg48temp9
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 772
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline
|
|
Quote: Originally posted by Fyndium ![](images/xpblue/lastpost.gif) | F
How to cool vacuum pump?
Mine gets very hot, above 90C when running for a longer period and too hot to touch. It would be trivial to cool down with water, but that'd be more
difficult to carry out. One crazy idea that came in mind is to put the pump in a thick plastic bag and immerse it in water bath so the pump exhaust
and other necessary accessories are not blocked. |
Thats a terrible idea. Most pump motors are cooled by a fan at one end so they should be operated with access to air. If you still want to cool the
pump body (not the motor) down attach a 6in fan to it to blow air over it.
I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
|
|
Fery
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1003
Registered: 27-8-2019
Location: Czechoslovakia
Member Is Offline
|
|
Fyndium:
My 2-stages vacuum pump is allowed to run 20 minutes without extra cooling, but for every run longer than 20 minutes it requires to add an extra fan
to blow air to its side(s). This is written exactly in its manual and also its seller told me the same. According the oil (few months old question) -
my bottle with oil (which I got together with my pump from the seller to replace the pump oil) states it is hydraulic oil, such oils are used in cars,
machinery etc.
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
This is 1-phase pump.
My logic was that cold water, even through plastic membrane, is many times better conductor of heat than air.
Only good thing about running the pump hot yesterday was that the slight water emulsion contamination cleared up due to water just simply evaporating
away.
|
|
Pages:
1
2 |