ChemichaelRXN
Hazard to Others
Posts: 103
Registered: 7-10-2010
Member Is Offline
Mood: Universal Eye
|
|
Thermobaric Composition
I am an innovator and part of my product idea uses the thermite I am going to speak about, but have you ever added wax pellets? I dont make anything
explosive or I definitely wouldn’t post this, but I know a little about this thermobaric material.
Apparently the mixture of Copper Oxide and German black aluminum (you need the carbon for quicker ignition) with wax pellets or other combustible
dense pellets (maybe plastic) is what makes up thermobaric explosives. I thought I’d share because I found it interesting. Copper oxide blasts with
a lot of heat quickly so I can see how adding something combustible adds a wave of dense heat.
Thermite reaction:
3 CuO + 2 Al —-> 3 Cu + 1 Al2O3
When this mixture explodes does it have an even higher m/s blast because of the wax added? Maybe someone that knows about this mixture can provide
more info.
Thanks!
|
|
|
Tsjerk
International Hazard
Posts: 3032
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Do you have a source for German black aluminium containing carbon? I can only find people on pyro forums claiming it does. I was under the impression
CuO/Al is fuse sensitive because of the particle size.
Did you compare the thermite with and without wax? In this mixture CuO is the oxidizer, I don't see CuO/wax being a very energetic mix. Why do you
think it would perform better with wax added?
I wouldn't be surprised if the wax it only there as a binder.
|
|
|
Herr Haber
International Hazard
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
I highly doubt it'll have any practical effect in that regard.
Cu thermite is "explosive" partly because of the BP of copper / partly because of all the air between the particles that gets superheated.
Air is replaced by wax, air is not heated, wax MELTS, takes away heat and burns though certainly not hot enough to keep the reaction going and you're
done.
Might be wrong but this is what I imagine would happen.
The spirit of adventure was upon me. Having nitric acid and copper, I had only to learn what the words 'act upon' meant. - Ira Remsen
|
|
|
ChemichaelRXN
Hazard to Others
Posts: 103
Registered: 7-10-2010
Member Is Offline
Mood: Universal Eye
|
|
I haven’t tried it with wax or plastic beads (just the thermite alone in the past), but I was thinking that the copper oxide thermite would explode
and then the wax pellets would burn and have a heat wave clap to it. (Thermobaric) The wax isnt part of the single displacement reaction.
|
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Very little.
It's not thermobaric.
Even wiki would tell you that "A thermobaric weapon, aerosol bomb, or vacuum bomb is a type of explosive that uses oxygen from the surrounding air to
generate a high-temperature explosion."
|
|
|
ChemichaelRXN
Hazard to Others
Posts: 103
Registered: 7-10-2010
Member Is Offline
Mood: Universal Eye
|
|
Anyway, I do know very little, I dont make anything explosive, just thought I’d share an interesting topic. I did research in the past which I cant
find any longer online that said they used copper oxide thermite with plastic pellets. It was a chart/list... That is what may have been used in the
FOAB. (There was a list of weapons with compositions and I could have sworn I seen copper oxide thermite listed as part of the composition)
|
|
|
ChemichaelRXN
Hazard to Others
Posts: 103
Registered: 7-10-2010
Member Is Offline
Mood: Universal Eye
|
|
It also does use oxygen from outside of the quick single displacement reaction to burn the wax/plastic pellets.
Pellets of tungsten oxide thermite added would be interesting to see as well as it has the highest melting point out of all elements. Copper’s
melting point is 1085C and tungsten is 3422C.
Anyway, I find it interesting to talk about and that is how far it goes. I feel it would work.
|
|
|
Fantasma4500
International Hazard
Posts: 1681
Registered: 12-12-2012
Location: Dysrope (aka europe)
Member Is Offline
Mood: dangerously practical
|
|
true thermobaric is where you have an explosive fuel-air mixture which then is initiated by a shockwave, one guy on youtube pulled it off first
setting off a charge dispersing gasoline, and then 3 metres away iirc with maybe 100ms delay a second charge went off, the idea is that the shockwave
causes the gas air mix to detonate at close to same speed as the shockwave hitting it, while gas air explosions are typically much slower
thermobaric is term sometimes used just to explain explosion with excessive fuel, i believe this is what chemichael is trying to accomplish, i see the
light in this idea, maybe you could get more knock out of it if you used magnalium or magnesium instead of aluminium, you can also get hydrogenated
castor oil, something is telling me that stuff would be better choice for this effect
|
|
|
ChemichaelRXN
Hazard to Others
Posts: 103
Registered: 7-10-2010
Member Is Offline
Mood: Universal Eye
|
|
Thanks for the great information to provide better clarity. (I wont try it out due to legal reasons, but I made thermite before, so I was wondering)
You are the same perception looking out, from the same elements around the universe.
You are everything to be anything to begin with.
Https://you-are.space
Https://syntharise.com
|
|
|
foreign maple
Harmless
Posts: 26
Registered: 14-12-2017
Location: Somewhere up north
Member Is Offline
Mood: I'm fine
|
|
wax is commonly added to energetic materials to increase the stability and density of the composition.
The majority Phlegmatized compositions contain ≈ 5% paraffin wax but in some instances this may differ. paraffin wax is not the only agent that is
used but it is quite common, it is used in RDX, Octyl and Pentolite. I would recommend using a smaller amount if you are planning to make a
thermobaric comp though.
|
|
|
Fyndium
International Hazard
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
Quote: Originally posted by Tsjerk  | | Do you have a source for German black aluminium containing carbon? I can only find people on pyro forums claiming it does. I was under the impression
CuO/Al is fuse sensitive because of the particle size. |
Only source that I have seen is that carbon/graphite powder is used in milling to prevent oxidation of aluminum powder.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
