garphield
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 58
Registered: 9-12-2019
Member Is Offline
|
|
Aluminium metal + base as a dehydrating agent?
Wiki says reaction is NaOH + Al + 3 H2O -> NaAl(OH)4 + 3/2 H2. As this converts water into hydroxide + hydrogen, there is no way for the
equilibrium to go backwards, so any water should be permanently eliminated. Obviously wont work for acids but for alcohols, amines, ect it might be
good. Might try this with some ethanol or ethylene glycol tomorrow.
One thing I am worried about is if it might react with alcohols in the same way as it would with water. I don't think it would be able to dehydrate
them to ethers or alkenes because that requires an acid catalyst iirc but I don't know for sure. If it just converts it into an alkoxide that should
be fine because it will be easy to hydrolyze. Don't think reductions would be an issue with most things because if that worked people would just use
this instead of aluminium amalgam.
|
|
Maurice VD 37
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 66
Registered: 31-12-2018
Member Is Offline
|
|
The trouble is that NaOH reacts with aluminum even without water. The equation is : 6 NaOH + 2 Al --> 2 Na3AlO3 + 3 H2
|
|
YoctoByte
Harmless
Posts: 8
Registered: 8-9-2017
Member Is Offline
Mood: No Mood
|
|
But wouldn't Na3AlO3 irreversibly react with water to form NaAl(OH)4 and NaOH? Because then it would still work.
If your solvent can withstand strong bases you could also use calcium oxide which might work even better.
|
|
h0lx
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 69
Registered: 31-12-2005
Member Is Offline
|
|
You could just make an aluminium amalgam, that reacts with water without a base
|
|
TriiodideFrog
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 108
Registered: 27-9-2020
Member Is Offline
|
|
Why don't you try adding HCl to Zinc? This reaction produces zinc chloride, a hygroscopic compound and hydrogen gas.
|
|
njl
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 609
Registered: 26-11-2019
Location: under the sycamore tree
Member Is Offline
Mood: ambivalent
|
|
Lots of things CAN be used as dehydrating agents, but its just not worth it most of the time. You can store 7 moles of water per mol of anhydrous
magnesium sulfate (which is cheap and everywhere), so why bother?
|
|
TriiodideFrog
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 108
Registered: 27-9-2020
Member Is Offline
|
|
True. If you want an interesting way to get magnesium sulfate, you can use heat Epsom salt ( Magnesium sulfate heptahydrate )
to remove the water. Surprisingly, Epsom salt is about 53% water! After the water is removed, you will get magnesium sulfate. Be warned, the flask you
use for the removal of water will probably crack.
|
|
YoctoByte
Harmless
Posts: 8
Registered: 8-9-2017
Member Is Offline
Mood: No Mood
|
|
If you don't want to waste a good flask you can also dry the salt in a glass oven dish. Since MgSO4 is non-toxic you can do this in your oven. Slowly
increase the temperature and don't make the layer too thick (1 cm max) because otherwise you end up with a solid mass which is hard to break up.
|
|
TriiodideFrog
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 108
Registered: 27-9-2020
Member Is Offline
|
|
Ok. I will try the experiment again with your suggestion. Thank you!
|
|
Tsjerk
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3026
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Throw the Epsom salt in a microwave resistant container of sorts, as long as the opening is not smaller than the container itself, and cover it with
something like a plate.
Put in a microwave at high for 5 minutes. You will be left with a bone dry brick of MgSO4. As soon as the water is gone the salt doesn't absorb
microwaves anymore, so you don't have to worry about overheating.
I use these ceramic cups you serve dessert in and put a plate normally used for sandwiches on top.
Just don't use a flask, that is just dumb.
|
|
Pumukli
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 693
Registered: 2-3-2014
Location: EU
Member Is Offline
Mood: No Mood
|
|
Perhaps the magnetron of the microwave oven requires a minimum load (say 50 ml water at least) in the cavity (the oven) to work properly. Running the
oven without this minimum load stresses the magnetron (wave relfections) and may be lead to its untimely death. If it was a real concern or not I
don't know.
|
|
symboom
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1143
Registered: 11-11-2010
Location: Wrongplanet
Member Is Offline
Mood: Doing science while it is still legal since 2010
|
|
Magnesium sulfate heptahydrate has a lot of water contained in it here is nilered extracting the water from it.
https://m.youtube.com/watch?v=8GVSuKkuLzY
|
|
garphield
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 58
Registered: 9-12-2019
Member Is Offline
|
|
the reason i asked is because i am working on a synthesis of ethylenediamine from cheap materials and en forms an azeotrope and is basically
impossible to get completely anhydrous - only thing i could find online is distilling over sodium metal. i thought this might work and if it does it
would be much better than an alkali metal because its much cheaper. if dehydrating agents that didnt chemically destroy the water worked i think those
people would have used them instead, and you can't use sulfur chloride, P2O5, thionyl chloride ect because those produce acids which immediately form
salts with en. although maybe en might be a strong enough base to react with Al and water on its own, en aluminate might be an interesting compound
but you would still probably use NaOH so you don't lose en as salts. a post with the details of the synth and yields will probably be up tomorrow or
sunday if you are interested, although after that i will probably do some more stuff to see if the yield can be improved and if it can be used to make
ethanolamine, 1,2-aminopropane, 1,2,3-aminopropane, ect.
|
|